No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - VPN

S1720, S2700, S5700, and S6720 V200R010C00

This document describes the VPN configuration procedures and provides configuration examples.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring the SPE

Configuring the SPE

Context

On an HVPLS network, SPEs are fully connected. You need to configure VSI peers between SPEs, and between SPEs and UPEs.

Perform the following steps on the SPE:

Procedure

  1. Run:

    system-view

    The system view is displayed.

  2. Run:

    vsi vsi-name static

    VSIs are created and the automatic member discovery mechanism is used.

  3. Run:

    pwsignal ldp

    LDP is configured as the PW signaling protocol and the VSI-LDP view is displayed.

  4. (Optional) Run:

    npe-upe mac-withdraw enable

    The SPE is enabled to forward the LDP MAC Withdraw messages that are received from another SPE to a UPE.

    By default, an SPE is not enabled to forward the LDP MAC Withdraw messages that are received from another SPE to a UPE.

    When an SPE receives an LDP MAC Withdraw message from another SPE, the SPE clears the local MAC table and learns MAC addresses. If the UPE does not clear the MAC table synchronously, communication may be interrupted. You can run this command to enable the SPE to forward the LDP MAC Withdraw message to the UPE to clear the MAC table on the UPE.

    In good network conditions, running this command speeds up network convergence. In bad network conditions, running this command generates a large amount of exchange messages, and therefore is not recommended.

  5. (Optional) Run:

    upe-upe mac-withdraw enable

    The SPE is enabled to forward the LDP MAC Withdraw messages that are received from a UPE to another UPE.

    By default, the SPE is not enabled to forward the LDP MAC Withdraw messages that are received from a UPE to another UPE.

    When an SPE receives an LDP MAC Withdraw message from a UPE, the SPE clears the local MAC table and learns MAC addresses. If another UPE does not clear the MAC table synchronously, communication may be interrupted. You can run this command to enable the SPE to forward the LDP MAC Withdraw message to another UPE to clear the MAC table on the UPE.

    In good network conditions, running this command speeds up network convergence. In bad network conditions, running this command generates a large amount of exchange messages, and therefore is not recommended.

  6. (Optional) Run:

    upe-npe mac-withdraw enable

    The SPE is enabled to forward the LDP MAC Withdraw messages that are received from a UPE to another SPE.

    By default, the SPE is not enabled to forward the LDP MAC Withdraw messages that are received from a UPE to another SPE.

    When an SPE receives an LDP MAC Withdraw message from a UPE, the SPE clears the local MAC table and learns MAC addresses. If another SPE does not clear the MAC table synchronously, communication may be interrupted. You can run this command to enable the SPE to forward the LDP MAC Withdraw message to another SPE to clear the MAC table on the SPE.

    In good network conditions, running this command speeds up network convergence. In bad network conditions, running this command generates a large amount of exchange messages, and therefore is not recommended.

  7. Run:

    vsi-id vsi-id

    The VSI ID is set.

  8. Run:

    peer peer-address [ negotiation-vc-id vc-id ] [ tnl-policy policy-name ]

    or run:

    peer peer-address [ negotiation-vc-id vc-id ] [ tnl-policy policy-name ] static-npe trans transmit-label recv receive-label

    A VSI peer is configured between SPEs.

  9. Run:

    peer peer-address [ negotiation-vc-id vc-id ] [ tnl-policy policy-name ] upe

    or run:

    peer peer-address [ negotiation-vc-id vc-id ] [ tnl-policy policy-name ] static-upe trans transmit-label recv receive-label

    A VSI peer is configured between the SPE and the UPE.

Translation
Download
Updated: 2019-08-21

Document ID: EDOC1000141944

Views: 102697

Downloads: 572

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next