No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - VPN

S1720, S2700, S5700, and S6720 V200R010C00

This document describes the VPN configuration procedures and provides configuration examples.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Licensing Requirements and Limitations for VPLS

Licensing Requirements and Limitations for VPLS

Involved Network Elements

Other network elements are not required.

License Requirements

VPLS is a basic feature of a switch and is not under license control.

Version Requirements

Table 7-9  Products and versions supporting VPLS

Product

Product Model

Software Version

S1700

S1720GFR

Not supported

S1720GW, S1720GWR

Not supported

S1720GW-E, S1720GWR-E

Not supported

S1720X, S1720X-E

Not supported

Other S1700 models

Models that cannot be configured using commands. For details about features and versions, see S1700 Documentation Bookshelf.

S2700

S2700SI

Not supported

S2700EI

Not supported

S2710SI

Not supported

S2720EI

Not supported

S2750EI

Not supported

S3700

S3700SI, S3700EI

Not supported

S3700HI

Not supported

S5700

S5700LI

Not supported

S5700S-LI

Not supported

S5710-C-LI

Not supported

S5710-X-LI

Not supported

S5700SI

Not supported

S5700EI

Not supported

S5710EI

V200R002C00, V200R003C00, V200R005(C00&C02)

S5720EI

V200R009C00, V200R010C00, V200R011C00, V200R011C10

S5720LI, S5720S-LI

Not supported

S5720SI, S5720S-SI

Not supported

S5730SI

Not supported

S5730S-EI

Not supported

S5700HI

V200R002C00, V200R003C00, V200R005(C00SPC500&C01&C02)

S5710HI

V200R003C00, V200R005(C00&C02&C03)

S5720HI

V200R007C10, V200R009C00, V200R010C00, V200R011C00, V200R011C10

S6700

S6700EI

V200R005(C00&C01&C02)

S6720EI

V200R008C00, V200R009C00, V200R010C00, V200R011C00, V200R011C10

S6720S-EI

V200R009C00, V200R010C00, V200R011C00, V200R011C10

S6720SI, S6720S-SI

Not supported

S6720LI, S6720S-LI

Not supported

NOTE:
To know details about software mappings, see Hardware Query Tool.

Feature Limitations

  • Do not add the PW to VLAN 1. If the PW is added to VLAN 1, the AC joins VLAN 1 in untagged mode and VLAN tags of packets are removed.

  • If an interface is used as a VPLS AC-side interface and a multicast inbound interface at the same time, multicast data cannot be forwarded normally on this interface. (S5720HI does not have this restriction.)
  • After receiving Layer 2 protocol packets such as STP, VBST, SMLK, LBT/LBDT, LACP, 3AH, 1AG, Y.1731, HGMP, LLDP, DLDP, GVRP, HVRP, DAD, LNP, VCMP, and BFD packets from an AC interface, a PE device determines whether it needs to process the packets. If not (for example, Layer 2 protocols are disabled), the PE device transparently transmits the Layer 2 protocol packets through the VPLS.
  • If L2VPN is configured on the device, the AC-side outbound interface does not support IP address-based load balancing when the interface is an Eth-Trunk interface.
  • If the PW-side interface is a Layer 3 interface switched by the undo portswitch command, the AC-side interface cannot be a Layer 3 interface or subinterface belonging to a Layer 3 interface; otherwise, traffic forwarding is abnormal. This rule applies to S5720EI, S6720EI, and S6720S-EI.

Translation
Download
Updated: 2019-08-21

Document ID: EDOC1000141944

Views: 109968

Downloads: 588

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next