No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search


To have a better experience, please upgrade your IE browser.


S5720HI V200R010C00 Configuration Guide - WLAN-AC

This document describes native AC (hereinafter referred to as WLAN AC) configuration procedures and provides configuration examples.

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Radio Calibration

Radio Calibration


On a WLAN, the operating status of APs is affected by the radio environment. For example, adjacent APs using the same working channel interfere with each other, and a large-power AP can interfere with adjacent APs if they work on overlapping channels. Radio calibration can dynamically adjust channels and power of APs managed by the same AC to ensure that the APs work in a way that optimizes performance.

  • Channel adjustment

    On a WLAN, adjacent APs must work on non-overlapping channels to avoid radio interference. For example, the 2.4 GHz frequency band is divided into 14 overlapping 20 MHz channels, as shown in Figure 6-1.

    For channels supported in different countries, see the Country Code & Channel Compliance Table. You can obtain this table at Huawei technical support website.
    Figure 6-1  Channels on the 2.4 GHz frequency band

    The 5 GHz frequency band has richer spectrum resources. In addition to 20 MHz channels, APs working on the 5 GHz frequency band support 40 MHz, 80 MHz, and larger-bandwidth channels, as shown in Figure 6-2.

    Figure 6-2  Channels

    • Two neighboring 20 MHz channels are bonded into a 40 MHz channel. One of the two 20 MHz channels is the primary channel, and the other the auxiliary channel.
    • Two neighboring 40 MHz channels are bonded into an 80 MHz channel. In an 80 MHz channel, one 20 MHz channel is selected as the primary channel. The other 20 MHz channel making up the 40 MHz channel with the primary channel is called the auxiliary 20 MHz channel. The 40 MHz channel not containing the primary channel is called the auxiliary 40 MHz channel.
    • Two neighboring 80 MHz channels are bonded into a 160 MHz channel. In a 160 MHz channel, one 20 MHz channel is selected as the primary channel. The other 20 MHz channels making up the 80 MHz channel with the primary channel are called the auxiliary 20 MHz channels. The 40 MHz channels not containing the primary channel are called the auxiliary 40 MHz channels. The 80 MHz channel not containing the primary channel is called the auxiliary 80 MHz channel. At most two 160 MHz channels are supported on the 5 GHz frequency band.
    • Two non-neighboring 80 MHz channels are bonded into an 80+80 MHz channel. The division of primary and auxiliary channels is similar to that for a 160 MHz channel. Compared to the 160 MHz channel, the 80+80 MHz channel allows for more than three non-overlapping channels on the 5 GHz frequency band, which can be used for cellular channel planning and meet wireless network deployment requirements.

    Figure 6-3 shows the channel bonding.

    Figure 6-3  Channel bonding example


    The primary channel is used for transmission of the management and control packets. A channel is idle only when its primary channel is idle.

    Figure 6-4 shows an example of channel distribution before and after channel adjustment. Before channel adjustment, both AP2 and AP4 use channel 6. After channel adjustment, AP4 uses channel 11 so that it does not interfere with AP2.

    After channel adjustment, each AP is allocated an optimal channel to minimize or avoid adjacent-channel or co-channel interference, ensuring reliable data transmission on the network.

    Figure 6-4  Channel adjustment

    In addition to optimizing radio performance, channel adjustment can also be used for dynamic frequency selection (DFS). In some regions, radar systems work in the 5 GHz frequency band, which can interfere with radio signals of APs working in the 5 GHz frequency band. The DFS function enables APs to automatically switch to other channels when they detect interference on their current working channels.

    During the DFS process, radar signals may be incorrectly determined. If radar signals are detected occasionally on a single AP, it may be a mistake. If radar signals are detected for multiple times on an AP or simultaneously on multiple APs, the radar signals may be determined. Then the APs can process the signals accordingly. To minimize misdetections, all Huawei AP models are optimized for DFS misdetections to distinguish radar signals and non-radar signals more accurately.
  • Power adjustment

    An AP's transmit power determines its radio coverage area. APs with higher power have larger coverage areas. A traditional method to control the radio power is to set the transmit power to the maximum value to maximize the radio coverage area. However, a high transmit power may cause interference with other wireless devices. Therefore, an optimal power is required to balance the coverage area and signal quality.

    The power adjustment function helps dynamically allocate proper power to APs according to the real-time radio environment. Power adjustment works according to the following:
    • When an AP is added to the network, the transmit power of neighboring APs decreases, as shown in Figure 6-5. The area of the circle around an AP represents the AP's coverage area after transmit power adjustment. When AP4 is added to the network, the transmit power of each AP decreases automatically.
    Figure 6-5  Transmit power of APs decreases

    • When an AP goes offline or fails, power of neighboring APs increases, as shown in Figure 6-6.
    Figure 6-6  Transmit power of APs increases


Radio calibration requires the following components for implementation:
  • AP: actively or passively collects radio environment information and sends the information to the AC. The AC then delivers the calibration results.
  • AC: maintains the AP neighbor topology based on radio environment information received from the AP, uses calibration algorithms to allocate AP channels and transmit power, sends calibration results to APs.

ACs support global radio calibration and partial radio calibration:

  • Global radio calibration:

    Global radio calibration takes effect on all APs managed by an AC. The AC controls channels and transmit power of all APs in the region to achieve best radio performance. Generally, this calibration mode is used on a newly deployed WLAN or a WLAN with a few services.

    The Figure 6-7 shows the global radio calibration process.
    Figure 6-7  Implementation of global radio calibration
    The global radio calibration process is as follows:
    1. After global radio calibration is enabled, the AC sends a notification to each AP, requesting the AP to start neighbor probing.
    2. The APs periodically implement neighbor probing and report neighbor information to the AC.
    3. After the AC receives probe results from all of the APs, it uses the global radio calibration algorithm to allocate channels and power to the APs.

      The global radio calibration algorithm includes the Dynamic Channel Allocation (DCA) algorithm and Transmit Power Control (TPC) algorithm.

    4. The AC delivers calibration results to the APs. After the AC implements global radio calibration for the first time, the AC starts the next global radio calibration until it receives neighboring information of all APs. The AC continuously implements global radio calibration in order to obtain the optimal and accurate calibration results.

    Neighbor probe

    Two neighbor probe modes are available.
    • Active probe: The AP actively sends Probe Request frames to notify surrounding APs of its existence. Active probe is used to establish neighbor relationships and obtain the maximum interference signal strength.

      The active probe process is as follows:
      1. An AP periodically sends Probe Request frames destined for a specified multicast address on different channels.
      2. After receiving the frames, surrounding APs learn that the AP is a neighbor and collects information about the AP, in which the Received Signal Strength Indicator (RSSI) is the key factor.
    • Passive probe: The AP receives neighbor information to detect neighboring APs. The passive probe is used to collect interference information from neighboring APs and rogue APs.

    Global calibration algorithm

    The global calibration algorithm achieves global optimization through partial optimizations. Global calibration is implemented through AP channel and power adjustment. Instead of being coupled to each other, the algorithms for channel adjustment (DCA) and power adjustment (TPC) are independent of each other.

    • DCA algorithm: Global calibration divides all APs into several calibration groups based on the relationships between the APs and allocates channels to each group. In each radio calibration group, simple exhaustion and iteration algorithms are used to list all possible AP-Channel combinations and choose the optimal combination.
    • TPC algorithm: The TPC algorithm aims to choose the proper transmit power which can meet coverage requirements, without causing large interference to neighboring APs. The TPC algorithm works in the following ways:
      1. The algorithm estimates the deployment density of APs based on the number of AP neighbors, and determines the initial transmit power, lower and upper interference thresholds.

        The level of interference specified by the lower interference threshold is low, and within the allowed range. In this case, two neighboring APs cannot detect interference from each other and can send packets simultaneously.

        The level of interference specified by the upper interference threshold is large. In this case, two neighboring APs can easily detect the interference and must compete to send packets through CSMA.

      2. The algorithm re-detects RSSIs of neighbors. If the interference caused by the neighbor is smaller than the lower interference threshold, the algorithm determines whether to raise transmit power according to their difference. If the interference caused by the neighbor is greater than the upper interference threshold, the algorithm determines whether to reduce transmit power according to their difference.
  • Partial radio calibration

    Partial radio calibration aims to adjust working channels and power of some APs to optimize the radio environment if it deteriorates in only some areas. Similar to the global radio calibration, the partial radio calibration uses DCA and TPC algorithms. Partial radio calibration is triggered in the following scenarios:

    • An AP goes online: When detecting that an AP goes online, the AC allocates a working channel and power to the new AP. To achieve the optimal performance, the AC may re-allocate the working channels and transmit power of neighboring APs. For example, to prevent interference between the new AP and its neighbors, the AC will reduce the transmit power of the AP neighbors.
    • An AP goes offline: When detecting that an AP goes offline, the AC executes the calibration algorithm to increase the transmit power of neighboring APs to eliminate coverage holes. An AP may be restarted unexpectedly or manually restarted for temporary maintenance. In this situation, the AC does not start the calibration algorithm immediately. Instead, the AC starts radio calibration only after the neighbor information is updated.
    • Interference from a rogue AP is detected: If a rogue AP is identified through neighbor probes, interference information is collected and used for radio calibration. If the interference value exceeds the threshold (-65 dBm by default), the interference is considered serious, and partial radio calibration is triggered. The device adjusts working channels of neighboring APs to avoid interference from the rogue AP.
    • The radio environment deteriorates: Radio environment deteriorates due to an increase in lost packets and error codes caused by interference or weak signals. In scenario, partial radio calibration may be triggered if it can improve the radio environment.
    • Interference from non-Wi-Fi devices is detected: Non-Wi-Fi devices, including microwave ovens and cordless phones, work on the same frequency as the APs, and may cause interference. If the spectrum analysis module identifies interference from non-Wi-Fi devices. If the interference is serious or large interference occurs multiple times in a specified period, the module triggers partial radio calibration and adjusts AP channels and power to avoid interference.
Updated: 2019-12-28

Document ID: EDOC1000141952

Views: 201114

Downloads: 522

Average rating:
This Document Applies to these Products

Related Version

Related Documents

Previous Next