No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Alarm Handling

S9300, S9300E, and S9300X V200R010C00

This document provides the explanations, causes, and recommended actions of alarms on the product.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
L2IFPPI_1.3.6.1.4.1.2011.5.25.160.3.1 hwMflpIfBlock

L2IFPPI_1.3.6.1.4.1.2011.5.25.160.3.1 hwMflpIfBlock

Description

L2IFPPI/4/MFLPIFBLOCK:OID [oid] Loop exists in VLAN [INTEGER], Interface [OCTET1] blocked, block-time is [GAUGE] for [OCTET2], Mac Address is [OCTET3].

MAC address flapping occurred and the interface was blocked.

Attribute

Alarm ID Alarm Severity Alarm Type
1.3.6.1.4.1.2011.5.25.160.3.1 Warning equipmentAlarm(5)

Parameters

Name Meaning
oid Indicates the ID of the MIB object.
INTEGER Indicates the VLAN ID.
OCTET1 Indicates the blocked interface name.
GAUGE Indicates the time when the interface was blocked.
OCTET3 Indicates the flapped MAC address.
OCTET2 Indicates the cause why the interface was blocked.

Impact on the System

Traffic cannot be received normally.

Possible Causes

Cause 1:

The interfaces where loops occurred were added to the same VLAN.

Cause 2:

Cables were connected incorrectly.

Cause 3:

STP was enabled to remove loops on the network.

Procedure

  1. Connect cables on the interfaces correctly and check whether the alarm persists.

    • If so, go to step 2.
    • If not, no further action is required.

  2. Check whether the two interfaces that learn the same MAC address can be added to different VLANs according to the networking.

    • If so, go to step 3.
    • If not, go to step 4.

  3. Add the two interfaces that learn the same MAC address to different VLANs. Then check whether the alarm persists.

    • If so, go to step 4.
    • If not, no further action is required.

  4. Check whether the ring network meets requirements.

    • If so, go to step 7.
    • If not, go to step 5.

  5. Perform the following operations to remove loops:

    (1) Run the display loop-detect eth-loop [ vlan vlan-id ] command to view the blocked interface.

    (2) Run the display mac-address vlan vlan-id command to search an interface that learns the MAC address.

    (3) Shut down one interface according to the networking.

    (4) Run the reset loop-detect eth-loop vlan vlan-id { all | interface interface-type interface-number | mac-address mac-address } command to delete the blocked interface.

  6. Check whether the alarm recovery message is received.

    • If so, no further action is required.
    • If not, go to step 7.

  7. Enable STP. Then check whether the alarm persists.

    • If so, contact technical support personnel.
    • If not, no further action is required.

Translation
Download
Updated: 2019-08-21

Document ID: EDOC1000142054

Views: 180738

Downloads: 44

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next