No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Alarm Handling

S9300, S9300E, and S9300X V200R010C00

This document provides the explanations, causes, and recommended actions of alarms on the product.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
IFNET_1.3.6.1.4.1.2011.5.25.41.3.5 hwIfFlowDown

IFNET_1.3.6.1.4.1.2011.5.25.41.3.5 hwIfFlowDown

Description

IFNET/4/IF_FLOWDOWN:OID [OID] The state of interface turned to DOWN because of FLOW DOWN. (Interface=[INTEGER], InterfaceIndex=[INTEGER], SysUpTime=[TIMETICK], FlowStatus=[INTEGER], InterfaceName=[STRING])

The trap was generated when the traffic on a particular interface was interrupted and then the interface became Down. The time and cause for the status change was recorded.

Attribute

Alarm ID Alarm Severity Alarm Type
1.3.6.1.4.1.2011.5.25.41.3.5 Warning processingErrorAlarm(4)

Parameters

Name Meaning

OID

Indicates the MIB object ID of the alarm.

Interface

Indicates the unfixed index of an interface.

InterfaceIndex

Indicates the fixed index of an interface.

SysUpTime

Indicates the time for system startup.

FlowStatus

Indicates the traffic status on an interface.

InterfaceName

Indicates the name of interface.

Impact on the System

Traffic will be interrupted.

Possible Causes

  • The mVRRP backup group changed to the non-Master state.

  • When the mVRRP backup group was in the Master state or the interface was bound to the PW, the shutdown command was run on the interface or the link was faulty.

  • The PW configuration was deleted.

Procedure

  1. Check whether the interface type is Virtual-Ethernet.

    • If so, go to Step 2.
    • If not, go to Step 7.

  2. Run the display l2vpn ccc-interface vc-type all command, to check whether there is the specified interface that the alarm occurs.

    • If so, go to Step 9.
    • If not, go to Step 3.

  3. Check whether a PW needs to be reconfigured.

    • If so, go to Step 4.
    • If not, go to Step 16.

  4. Reconfigure a PW. For details, see S9300, S9300E, and S9300X V200R010C00 Configuration Guide - VPN.
  5. Run the display l2vpn ccc-interface vc-type all command, to check whether there is the specified interface that the alarm occurs.

    • If so, go to Step 6.
    • If not, go to Step 15.

  6. Run the display interface command to check whether the physical status and link protocol status of the interface are Up.

    • If so, go to Step 16.
    • If not, go to Step 9.

  7. Run the display vrrp binding admin-vrrp command to check whether the interface is bound to the mVRRP backup group.

    • If so, go to Step 8.
    • If not, go to Step 15.

  8. Run the display vrrp admin-vrrp command to check whether the mVRRP backup group to which the interface is bound is in the Master state.

    • If so, go to Step 9.
    • If not, go to Step 12.

  9. Run the display this command in the interface view to check whether the shutdown command is configured on the interface.

    • If so, go to Step 10.
    • If not, go to Step 11.

  10. Run the undo shutdown command in the interface view. Then, run the display this interface command to check whether the interface status is Up.

    • If so, go to Step 16.
    • If not, go to Step 6.

  11. Check and change the physical link to ensure that the physical link works normally. Then, run the display this interface command to check whether the interface status is Up.

    • If so, go to Step 16.
    • If not, go to Step 15.

  12. Check whether the status of the mVRRP backup group needs to be switched.

    • If so, go to Step 13.
    • If not, go to Step 16.

  13. Switch the status of the mVRRP backup group. For details, see S9300, S9300E, and S9300X V200R010C00 Configuration Guide - Reliability VRRP Configuration.
  14. Run the display this interface command in the interface view to check whether the physical status and link protocol status of the interface are Up.

    • If so, go to Step 16.
    • If not, go to Step 15.

  15. Collect alarm information and configuration information, and then contact technical support personnel.
  16. End.
Translation
Download
Updated: 2019-08-21

Document ID: EDOC1000142054

Views: 180431

Downloads: 44

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next