No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Alarm Handling

S9300, S9300E, and S9300X V200R010C00

This document provides the explanations, causes, and recommended actions of alarms on the product.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
OSPFV3_1.3.6.1.4.1.2011.5.25.147.0.5 hwOspfv3VirtIfConfigError

OSPFV3_1.3.6.1.4.1.2011.5.25.147.0.5 hwOspfv3VirtIfConfigError

Description

OSPFV3/2/VIFCFGERR:OID [oid] The configuration of the virtual interface is incorrect. (AreaId=[integer], VirtualNbrRouterId=[gauge], RouterId=[gauge], VIfState=[integer], ErrorType=[integer], PacketType=[integer])

Configurations of the virtual link interface were incorrect. A possible cause is that the configurations of the parameters conflicted.

Attribute

Alarm ID Alarm Severity Alarm Type
1.3.6.1.4.1.2011.5.25.147.0.5 Major processingErrorAlarm(2)

Parameters

Name Meaning

oid

Indicates the MIB object ID of the alarm.

AreaId

Indicates the ID of the OSPFv3 area. The value is a decimal integer.

VirtualNbrRouterId

Indicates the Router ID of the virtual neighbor. The value is a decimal integer.

RouterId

Indicates the Router ID of the local switch. The value is a decimal integer.

VIfState

Indicates the state of the virtual neighbor.
  • 1: Down
  • 2: Attempt
  • 3: Init
  • 4: 2-Way
  • 5: Exstart
  • 6: Exchange
  • 7: Loading
  • 8: Full

Errortype

Indicates the type of the error.
  • 1: badVersion
  • 2: areaMismatch
  • 3: unknownNbmaNbr
  • 4: unknownVirtualNbr
  • 5: helloIntervalMismatch
  • 6: deadIntervalMismatch
  • 7: optionMismatch
  • 8: mtuMismatch
  • 9: duplicateRouterId
  • 10: noError

Packettype

Indicates the type of the packet.
  • 1: Hello
  • 2: DD(Data base Description) packet
  • 3: LS Request
  • 4: LS Update
  • 5: LS Acknowledgement
  • 6: NULL packet

Impact on the System

This trap is generated when the virtual link interface received a packet indicating parameters were incorrectly configured. Such configuration errors generally occur during the deployment test or cutover. You can modify the parameters on the two ends to be consistent to rectify the fault, and services will not be affected.

Possible Causes

The configurations of the interfaces on the two ends of the virtual link conflicted.

Procedure

  1. Run the display ospfv3 vlink and display current-configuration interface commands to check whether the configurations of the two interfaces are consistent.

    • If so, go to Step 3.

    • If not, go to Step 2.

  2. Perform the following operations according to the networking:

    • If it is allowed to modify the configurations of the two ends to be consistent, go to Step 4.

    • If it is not allowed to modify the configurations of the two ends to be consistent, go to Step 3.

  3. Collect alarm information and configuration information, and then contact technical support personnel.
  4. End.

Related Information

None

Translation
Download
Updated: 2019-08-21

Document ID: EDOC1000142054

Views: 183841

Downloads: 44

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next