No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Alarm Handling

S9300, S9300E, and S9300X V200R010C00

This document provides the explanations, causes, and recommended actions of alarms on the product.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
BASETRAP_1.3.6.1.4.1.2011.5.25.129.2.2.21 hwPowerInsufficiencyAlarm

BASETRAP_1.3.6.1.4.1.2011.5.25.129.2.2.21 hwPowerInsufficiencyAlarm

Description

BASETRAP/2/POWERLACK: OID [oid] The available power of device is not enough for the board. (Index=[INTEGER], Severity=[INTEGER], ProbableCause=[INTEGER], EventType=[INTEGER], PhysicalContainedIn=[INTEGER], PhysicalName="[OCTET]", EntityRatedPower=[INTEGER], DevAvailablePower=[INTEGER], DeviceTotalPower=[INTEGER])

When a board is installed, the system allocates the rated power of the board to the board. This alarm is generated when the available power of the system is smaller than the rated power of the board.

Attribute

Alarm ID Alarm Severity Alarm Type
1.3.6.1.4.1.2011.5.25.129.2.2.21 Major environmentalAlarm(6)

Parameters

Name Meaning
[oid] Indicates the ID of the MIB object.
Index Indicates the index of the entity. The entity in an alarm on power is a board.
Severity Indicates the severity level of the alarm.
ProbableCause Indicates the possible causes of the alarm. The codes of the possible causes are as follows:

533: IANAITUPROBABLECAUSE_POWERPROBLEMS indicates that the power module is faulty.

EventType Indicates the alarm type:
  • communicationsAlarm (2)
  • qualityOfServiceAlarm (3)
  • processingErrorAlarm (4)
  • equipmentAlarm (5)
  • environmentalAlarm (6)

This alarm is an alarm of the equipmentAlarm type.

PhysicalName Indicates the physical name of the entity.
PhysicalContainedIn Indicates the index of the parent entity of the alarm entity. In the alarm, this parameter indicates the index of the slot where the power module is located.
EntityRatedPower Indicates the rated power of the board.
DevAvailablePower Indicates the available power of the system.
DeviceTotalPower Indicates the total power of the system.

Impact on the System

The board to be installed cannot be switched on.

Possible Causes

The available power of the system is less than the rated power of the board.

Procedure

  1. Run the display power system command to check the total power and available power of the system and the rated power of each board that is switched on.
  2. Check whether this board needs to be installed.

    • If so, go to step 3.
    • If not, remove this board. The alarm handling ends.

  3. Check whether other unnecessary boards can be removed.

    • If so, go to step 4.
    • If not, this board cannot be installed. The alarm handling ends.

  4. Remove unnecessary boards, and then run the display power system command to check whether the remaining power is sufficient for the newly installed board.

    • If so, the alarm handling ends.
    • If not, go to step 3.

Translation
Download
Updated: 2019-08-21

Document ID: EDOC1000142054

Views: 189193

Downloads: 44

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next