No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - VPN

S9300, S9300E, and S9300X V200R010C00

This document describes the VPN configuration procedures and provides configuration examples.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring IGP GR on the Backbone Network

Configuring IGP GR on the Backbone Network

Context

When configuring GR on the backbone network, configure the corresponding IGP GR (IS-IS GR or OSPF GR) based on the specific IGP protocol running on the backbone network.

Procedure

  • Configure IS-IS GR on the backbone network.

    If IS-IS is running on the public network, do as follows on the related PEs and Ps on the backbone network:

    1. Run:

      system-view

      The system view is displayed.

    2. Run:

      isis process-id

      The IS-IS view is displayed.

    3. Run:

      graceful-restart

      The IS-IS GR capability is enabled.

      By default, the IS-IS GR capability is disabled.

    4. (Optional) Run:

      graceful-restart interval interval-value

      The interval for reestablishing the IS-IS GR session is configured.

      The interval for reestablishing the IS-IS GR session is set to the Hold time in the IS-IS Hello PDU. In this way, the neighbor does not terminate the peer relationship with the switch when the switch performs the AMB/SMB switchover.

      By default, the interval for reestablishing the IS-IS GR session is 300 seconds.

    5. (Optional) Run:

      graceful-restart suppress-sa

      The GR Restarter is configured to suppress the advertisement of the peer relationship when it is restarting.

      The suppress advertisement (SA) bit is used in the Hello PDUs by a restarting switch to request its neighbors to suppress advertising the adjacency to the restarting switch. The SA bit is removed once its database synchronization is over. Enabling this feature avoids the black hole effect caused by sending and receiving LSP during the restart process.

      If the administrator does not want the restarting switch to set the SA bit in its Hello PDUs, the administrator can use the undo graceful-restart suppress-sa command to disable it.

      By default, the SA bit does not take effect.

  • Configure OSPF GR on the backbone network.

    If OSPF is running on the public network, do as follows on the related PEs and Ps on the backbone network:

    1. Run:

      system-view

      The system view is displayed.

    2. Run:

      ospf process-id

      The OSPF view is displayed.

    3. Run:

      opaque-capability enable

      The opaque-lsa capability is enabled.

    4. Perform the following as needed:

      • To enable the GR capability for OSPF, run:

        graceful-restart
      • To enable the GR Help capability for OSPF at which the Restarter performs the GR, run:

        graceful-restart helper-role { { { ip-prefix ip-prefix-name | acl-number acl-number | acl-name acl-name } | ignore-external-lsa | planned-only } * | never }

      It is suggested to enable the GR capability for OSPF on all the related PEs and Ps on the backbone network.

      By default, the GR capability for OSPF and the GR Help capability for OSPF are disabled.

Translation
Download
Updated: 2019-08-21

Document ID: EDOC1000142068

Views: 114503

Downloads: 210

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next