No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - VPN

S9300, S9300E, and S9300X V200R010C00

This document describes the VPN configuration procedures and provides configuration examples.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring a CCC VLL

Configuring a CCC VLL

Context

A CCC VLL does not require signaling negotiation or exchange of control packets; therefore, it requires few resources and is easy to configure. However, it requires manual configuration which makes network maintenance and expansion difficult. This mode applies to small-scale MPLS networks with simple topologies.

The CCC mode supports both local and remote connections.
  • Configure a local CCC connection when two CE devices connected to the same PE device.
  • Configure a remote CCC connection when two CE devices connected to different PE devices.

Pre-configuration Tasks

  • Before configuring a local CCC connection, enable basic MPLS capabilities on the PE and P devices of the MPLS backbone network.

  • Before configuring a remote CCC connection, complete the following tasks:
    • Configure static routes or an Interior Gateway Protocol (IGP) on the PE and P devices of the MPLS backbone network to implement IP connectivity.

    • Enable basic MPLS capabilities on the PE and P devices of the MPLS backbone network.

Procedure

  • Configure a local CCC connection.

    To create a local CCC connection, configure the inbound and outbound interfaces of the CCC connection on the PE device. Perform the following operations on the PE device:

    1. Run:

      system-view

      The system view is displayed.

    2. Run:

      mpls l2vpn

      MPLS L2VPN is enabled and the MPLS L2VPN view is displayed.

      MPLS L2VPN must be enabled on the PE device before you configure a VLL.

    3. Run:

      quit

      Return to the system view.

    4. Run:

      ccc ccc-connection-name interface interface-type1 interface-number1 [ raw | tagged ] out-interface interface-type2 interface-number2 [ raw | tagged ]

      A local CCC connection is created.

      The local CCC connection is bidirectional; therefore, only one connection is required. The device can create local CCC connections only on VLANIF interfaces and uses the raw encapsulation mode by default.

  • Configure a remote CCC connection.

    To create a remote CCC connection, configure the inbound interface, outbound interfaces, inbound label, and outbound label for the connection on the PE devices at both ends. If a P device is deployed between the two PE devices, configure a static LSP in both directions on the P device.

    The remote CCC connection is unidirectional; therefore, two connections are required.

    • Perform the following operations on the PE devices at both ends of a VC:

      1. Run:

        system-view

        The system view is displayed.

      2. Run:

        mpls l2vpn

        MPLS L2VPN is enabled and the MPLS L2VPN view is displayed.

      3. Run:

        quit

        Return to the system view.

      4. Run:

        ccc ccc-connection-name interface interface-type1 interface-number1 [ raw | tagged ] in-label in-label-value out-label out-label-value nexthop nexthop-address [ control-word | no-control-word ]

        A remote CCC connection is created.

        The device can create remote CCC connections only on VLANIF interfaces. A remote CCC connection uses the raw encapsulation mode by default.

    • Perform the following operations on the P device on the VC:

      1. Run:

        system-view

        The system view is displayed.

      2. Run:

        static-lsp transit lsp-name [ incoming-interface interface-type interface-number ] in-label in-label { nexthop nexthop-address | outgoing-interface interface-type interface-number } * out-label out-label

        The P device is configured as the transit label switching router (LSR) of the static LSP.

    When creating a remote CCC connection, map the AC interfaces on the PE devices to static LSPs and configure static LSPs in both directions on the P device to exclusively transmit CCC connection data. You do not need to enable MPLS L2VPN on the P device.

NOTE:

The incoming label of the CCC and receive label of the SVC all range from 16 to 1023. They are in the same label space with those reserved for static LSPs. However, the outgoing label of the CCC and the transmit label of the SVC range from 0 to 1048575 because they are used for interworking.

Checking the Configuration

After completing the CCC VLL configuration, run the following commands to check information about the CCC connection and interfaces used by the connection.

  • Run the display vll ccc [ ccc-name | type { local | remote } ] command to check information about the CCC connection.
  • Run the display l2vpn ccc-interface vc-type ccc [ down | up ] command to check information about interfaces used by the CCC connection.
Translation
Download
Updated: 2019-08-21

Document ID: EDOC1000142068

Views: 112288

Downloads: 208

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next