No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S12700 V200R010C00 Configuration Guide - Device Management

This document describes the principles and configurations of the Device Management features, and provides configuration examples of these features.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Displaying Power Supply and Power Information

Displaying Power Supply and Power Information

Context

When a power supply fault occurs on a device, you can run the following display commands to view power supply and power information.

Procedure

  • Run the display power command to view power supply information.
  • Run the display power system command to view system power information.

FAQ

How Can I Determine Whether the Power Supply Status Is Abnormal?

The power supply status is abnormal if either of the following situations occurs:
  1. Run the display power command to view the power supply status. If the State field displays NotSupply, the power module is not supplying power. Check whether the power module is installed properly and whether the power switch is turned on.
    <HUAWEI> display power
    --------------------------------------------------------------------------
     PowerID  Online  Mode   State      Current(A)   Voltage(V)   RealPwr(W)
    --------------------------------------------------------------------------
     PWR1     Present AC     NotSupply  -            -            -
     PWR2     Present AC     Supply     0.82         53.40        43.79
     PWR3     Present AC     Supply     0.97         53.51        51.90
     PWR4     Present AC     Supply     0.95         53.51        50.83
     PWR5     Absent  -      -          -            -            -
     PWR6     Absent  -      -          -            -            -           
  2. Run the display device command to view the power supply status. If the State field displays Unregistered or Abnormal, the power supply status is abnormal. You can run the display alarm all command to check whether there are any power supply alarms.

    <HUAWEI> display alarm all
    ----------------------------------------------------------------------------
    Level          Date        Time                Info
    
    Warning      2014-07-28  15:19:02        Fan is invalid for some reason.(Phys
                                         icalName=[FAN2], EntityTrapFaultID=139266
                                         )
    Emergency    2014-07-28  15:19:00        Power is invalid for not support DC1
                                         600 and DC2400.(PhysicalName=[PWR2])
    Emergency    2014-07-28  15:18:59        Power is invalid for not support DC1
                                         600 and DC2400.(PhysicalName=[PWR1])
    ----------------------------------------------------------------------------  
    Common power supply alarm information is as follows:
    • When the alarm information contains Power is invalid for not support, an incompatible power module is installed in the device.
    • When PWR_LACK and SWITCH_STAT sensor alarms are generated on the same power module, the power module is installed but is not connected to any power cable or the power switch is not turned on.
    • If only the PWR_FAULT alarm is generated, the power module is experiencing a fan failure, output overvoltage, external short circuit, output failure, or input failure.

For details about how to troubleshoot the abnormal power supply status, see "A Power Module Does Not Work Normally" in the Troubleshooting - Hardware Troubleshooting.

How Can I Determine a DC or AC Power Module?

Run the display power command to view power supply information. If the Mode field displays AC, the power module is an AC power module. If the Mode field displays DC, the power module is a DC power module.
<HUAWEI> display power
--------------------------------------------------------------------------
 PowerID  Online  Mode   State      Current(A)   Voltage(V)   RealPwr(W)
--------------------------------------------------------------------------
 PWR1     Present AC     NotSupply  -            -            -
 PWR2     Present AC     Supply     1.45         53.40        77.43
 PWR3     Present AC     Supply     1.47         53.51        78.66
 PWR4     Present AC     Supply     1.45         53.51        77.59
 PWR5     Absent  -      -          -            -            -
 PWR6     Absent  -      -          -            -            -

How Can I View the Power of Power Modules?

Run the display power system command to view power information, including the total system power, reserved system power, and card rated power. Card rated power information displays the rated power of power modules.
<HUAWEI> display power system
 The total power supplied   : 1600.00(W)
 Number of backup power supplies: 0
 The maximum power needed   : 1295.40(W)  (Include the remain reserved power)
 The remain reserved power  : 101.00(W)
 The remain power           : 304.60(W)
 The system rated power detail information :
-------------------------------------------------
 Slot      BoardName      State        Power(W)
-------------------------------------------------
 1         LPU board      On           131.00
 2         LPU board      On           339.00
 3         LPU board      On           130.00
 4         LPU board      On           178.40
 6         MPU board      On           100.00
 8         SFU board      On           83.00
 CMU1      CMU board      On           1.00
 FAN1      FAN board      On           116.00
 FAN2      FAN board      On           116.00
 PWR1      PWR board      On           800.00
 PWR2      PWR board      On           800.00

What Are the MIB OIDs of System Power Information?

The following table describes the MIB OIDs of system power information.

Object Name

OID

Syntax

Description

Max Access

hwSystemPowerDeviceID

1.3.6.1.4.1.2011.5.25.31.1.1.14.1.1

Integer32

This object indicates the device ID.

read-only

hwSystemPowerTotalPower

1.3.6.1.4.1.2011.5.25.31.1.1.14.1.2

Integer32

This object indicates the total system power.

read-only

hwSystemPowerUsedPower

1.3.6.1.4.1.2011.5.25.31.1.1.14.1.3

Integer32

This object indicates the used system power.

read-only

hwSystemPowerRemainPower

1.3.6.1.4.1.2011.5.25.31.1.1.14.1.4

Integer32

This object indicates the remaining system power.

read-only

Translation
Download
Updated: 2019-08-21

Document ID: EDOC1000142080

Views: 109585

Downloads: 144

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next