No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S12700 V200R010C00 Configuration Guide - Device Management

This document describes the principles and configurations of the Device Management features, and provides configuration examples of these features.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Setting Up an SVF System (AP Access)

Setting Up an SVF System (AP Access)

Context

In an SVF system shown in Figure 9-7, APs can be connected to the parent, level-1 ASs directly and indirectly, and level-2 ASs.

Figure 9-7  AP access

NOTE:
  • If APs need to be connected to the SVF system and managed by the parent, the parent must be the S12700/S9700/S7700/S5720HI and the S12700/S9700/S7700 must have X series cards installed.

  • When APs are connected to a non-X series card, you must add the non-X series card and X series card of the parent to the same WLAN work group. By default, all interface cards automatically join the default WLAN work group named default. For details, see Connecting an AP to a Non-X series Interface Card.

  • When an AS connects to APs, all member ports of the Eth-Trunk bound to the fabric port that connects the parent to the AS must be ports on X series cards or ports on non-X series cards. Otherwise, APs cannot go online.

  • If an AP has been connected to the parent before the SVF function is enabled, the parent cannot collect topology information about the AP after the uni-mng command is used to enable the SVF function. You need to run the commit { all | ap ap-id } command in the WLAN view to commit the AP configuration. Subsequently, the parent can collect topology information about the AP.

Procedure

  • Connect an AP to the parent.

    When an AP is connected to the parent, the access configuration performed on the parent is the same as that on an AC. For details about connecting an AP to an AC, see the S12700 V200R010C00 Configuration Guide - WLAN-AC.

  • Connect an AP to an AS.
    1. Run:

      system-view

      The system view is displayed.

    2. Run:

      uni-mng

      The uni-mng view is displayed.

    3. Run:

      port-group connect-ap name group-name

      An AP port group is created and the AP port group view is displayed.

      You can create only one AP port group.

    4. Add the ports that connect ASs to APs to the AP port group.

      • Run:
        as name as-name interface {
        { interface-type interface-number1 [ to interface-number2 ] } &<1-10> | all }

        Ports of the AS with a specified name are added to the AP port group.

      • Run:

        as name-include string interface all

        Ports of ASs of which the name contains a specified string are added to the AP port group.

    5. Run:

      quit

      Exit from the AP port group view.

    6. Run:

      commit as { name as-name | all }

      The configuration is committed.

    7. Other AP connection configurations or service configurations, for example, the AP authentication mode and AP profiles, are the same as those performed when an AP is connected to an AC. For details, see S12700 V200R010C00 Configuration Guide - WLAN-AC.
Translation
Download
Updated: 2019-08-21

Document ID: EDOC1000142080

Views: 115236

Downloads: 149

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next