No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Enterprise
Worldwide
Huawei Global - English
Search
Support Documentation
S12700 V200R010C00 Configuration Guide - Ethernet Switching

This document describes the configuration of Ethernet services, including configuring link aggregation, VLANs, Voice VLAN, VLAN mapping, QinQ, GVRP, MAC table, STP/RSTP/MSTP, SEP, and so on.

Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Example for Configuring a Single RRPP Ring with Multiple Instances

Example for Configuring a Single RRPP Ring with Multiple Instances

Networking Requirements

As shown in Figure 18-39, on a ring network, idle links are required to forward data. In this way, data in different VLANs are forwarded along different paths, improving network efficiency and implementing load balancing.

Figure 18-39  Network of single RRPP ring with multiple instances

Data Plan

Table 18-6 shows the mapping between protected VLANs and instances in Domain 1 and Domain 2.

Table 18-6  Mapping between the protected VLAN and instance

Domain ID

Control VLAN ID

Data VLAN ID

Instance ID

Domain 1

VLANs 5 and 6

VLANs 100 to 200

Instance 1

Domain 2

VLANs 10 and 11

VLANs 201 to 300

Instance 2

Table 18-7 shows the master node on each ring and the primary and secondary interfaces on each master node.

Table 18-7  Master node and its primary and secondary interfaces

Ring ID

Master Node

Primary Port

Secondary Port

Ring 1 in Domain 1

PEAGG

GE1/0/0

GE2/0/0

Ring 1 in Domain 2

PEAGG

GE2/0/0

GE1/0/0

Configuration Roadmap

The configuration roadmap is as follows:

  1. Create different RRPP domains and control VLANs.

  2. Map the VLANs that need to pass through Ring 1 in Domain 1 to Instance 1, including data VLANs and control VLANs.

    Map the VLANs that need to pass through Ring 1 in Domain 2 to Instance 2, including data VLANs and control VLANs.

  3. Configure interfaces to be added to the RRPP domain on the devices so that data can pass through the interfaces. Disable protocols that conflict with RRPP, such as STP.

  4. Configure protected VLANs and create RRPP rings in RRPP domains.

    1. Add UPEA, UPEB, UPEC, and PEAGG to Ring 1 in Domain 1. Configure PEAGG as the master node on Ring 1 in Domain 1 and configure UPEA, UPEB, and UPEC as transit nodes.

    2. Add UPEA, UPEB, UPEC, and PEAGG to Ring 1 in Domain 2. Configure PEAGG as the master node on Ring 1 in Domain 2 and configure UPEA, UPEB, and UPEC as transit nodes.

  5. Enable the RRPP ring and RRPP protocol on devices to make RRPP take effect.

Procedure

  1. Create an RRPP domain and its control VLAN.

    # Configure UPEA. The configurations on UPEB, UPEC, and PEAGG are similar to that on UPEA and not mentioned here. For details, see the configuration files.

    <HUAWEI> system-view
[HUAWEI] sysname UPEA
[UPEA] rrpp domain 1
[UPEA-rrpp-domain-region1] control-vlan 5
[UPEA-rrpp-domain-region1] quit
[UPEA] rrpp domain 2
[UPEA-rrpp-domain-region2] control-vlan 10
[UPEA-rrpp-domain-region2] quit

  2. Configure instances, and map it to the data VLANs and control VLANs allowed by the RRPP interface.

    # Configure UPEA. The configurations on UPEB, UPEC, and PEAGG are the same as that of UPEA and not mentioned here. For details, see the configuration files.

    [UPEA] vlan batch 100 to 300
[UPEA] stp region-configuration 
[UPEA-mst-region] instance 1 vlan 5 6 100 to 200
[UPEA-mst-region] instance 2 vlan 10 11 201 to 300
[UPEA-mst-region] active region-configuration
[UPEA-mst-region] quit

  3. Configure the interfaces to be added into the RRPP rings.

    # Configure UPEA. The configurations on UPEB, UPEC, and PEAGG are the same as that of UPEA and not mentioned here. For details, see the configuration files.

    [UPEA] interface gigabitethernet 1/0/0
[UPEA-GigabitEthernet1/0/0] port link-type trunk
[UPEA-GigabitEthernet1/0/0] undo port trunk allow-pass vlan 1
[UPEA-GigabitEthernet1/0/0] port trunk allow-pass vlan 100 to 300
[UPEA-GigabitEthernet1/0/0] stp disable
[UPEA-GigabitEthernet1/0/0] quit
[UPEA] interface gigabitethernet 2/0/0
[UPEA-GigabitEthernet2/0/0] port link-type trunk
[UPEA-GigabitEthernet2/0/0] undo port trunk allow-pass vlan 1
[UPEA-GigabitEthernet2/0/0] port trunk allow-pass vlan 100 to 300
[UPEA-GigabitEthernet2/0/0] stp disable
[UPEA-GigabitEthernet2/0/0] quit

  4. Specify a protected VLAN, and create and enable an RRPP ring.

    # Configure UPEA as a transit node on Ring 1 in Domain 1 and specify primary and secondary interfaces on UPEA.

    [UPEA] rrpp domain 1
[UPEA-rrpp-domain-region1] protected-vlan reference-instance 1
[UPEA-rrpp-domain-region1] ring 1 node-mode transit primary-port gigabitethernet 1/0/0 secondary-port gigabitethernet 2/0/0 level 0
[UPEA-rrpp-domain-region1] ring 1 enable
[UPEA-rrpp-domain-region1] quit

    # Configure UPEA as a transit node on Ring 1 in Domain 2 and specify primary and secondary interfaces on UPEA.

    [UPEA] rrpp domain 2
[UPEA-rrpp-domain-region2] protected-vlan reference-instance 2
[UPEA-rrpp-domain-region2] ring 1 node-mode transit primary-port gigabitethernet 1/0/0 secondary-port gigabitethernet 2/0/0 level 0
[UPEA-rrpp-domain-region2] ring 1 enable
[UPEA-rrpp-domain-region2] quit

    # Configure UPEB as a transit node on Ring 1 in Domain 1 and specify primary and secondary interfaces on UPEB.

    [UPEB] rrpp domain 1
[UPEB-rrpp-domain-region1] protected-vlan reference-instance 1
[UPEB-rrpp-domain-region1] ring 1 node-mode transit primary-port gigabitethernet 1/0/0 secondary-port gigabitethernet 2/0/0 level 0
[UPEB-rrpp-domain-region1] ring 1 enable
[UPEB-rrpp-domain-region1] quit

    # Configure UPEB as a transit node on Ring 1 in Domain 2 and specify primary and secondary interfaces on UPEB.

    [UPEB] rrpp domain 2
[UPEB-rrpp-domain-region2] protected-vlan reference-instance 2
[UPEB-rrpp-domain-region2] ring 1 node-mode transit primary-port gigabitethernet 1/0/0 secondary-port gigabitethernet 2/0/0 level 0
[UPEB-rrpp-domain-region2] ring 1 enable
[UPEB-rrpp-domain-region2] quit

    # Configure UPEC as a transit node on Ring 1 in Domain 1 and specify primary and secondary interfaces on UPEC.

    [UPEC] rrpp domain 1
[UPEC-rrpp-domain-region1] protected-vlan reference-instance 1
[UPEC-rrpp-domain-region1] ring 1 node-mode transit primary-port gigabitethernet 1/0/0 secondary-port gigabitethernet 2/0/0 level 0
[UPEC-rrpp-domain-region1] ring 1 enable
[UPEC-rrpp-domain-region1] quit

    # Configure UPEC as a transit node on Ring 1 in Domain 2 and specify primary and secondary interfaces on UPEC.

    [UPEC] rrpp domain 2
[UPEC-rrpp-domain-region2] protected-vlan reference-instance 2
[UPEC-rrpp-domain-region2] ring 1 node-mode transit primary-port gigabitethernet 1/0/0 secondary-port gigabitethernet 2/0/0 level 0
[UPEC-rrpp-domain-region2] ring 1 enable
[UPEC-rrpp-domain-region2] quit

    # Configure PEAGG as the master node on Ring 1 in Domain 1, with GE1/0/0 as the primary interface and GE2/0/0 as the secondary interface.

    [PEAGG] rrpp domain 1
[PEAGG-rrpp-domain-region1] protected-vlan reference-instance 1
[PEAGG-rrpp-domain-region1] ring 1 node-mode master primary-port gigabitethernet 1/0/0 secondary-port gigabitethernet 2/0/0 level 0
[PEAGG-rrpp-domain-region1] ring 1 enable
[PEAGG-rrpp-domain-region1] quit

    # Configure PEAGG as the master node on Ring 1 in Domain 2, with GE2/0/0 as the primary interface and GE1/0/0 as the secondary interface.

    [PEAGG] rrpp domain 2
[PEAGG-rrpp-domain-region2] protected-vlan reference-instance 2
[PEAGG-rrpp-domain-region2] ring 1 node-mode master primary-port gigabitethernet 2/0/0 secondary-port gigabitethernet 1/0/0 level 0
[PEAGG-rrpp-domain-region2] ring 1 enable
[PEAGG-rrpp-domain-region2] quit

  5. Enable RRPP.

    # Configure UPEA. The configurations on UPEB, UPEC, and PEAGG are the same as that of UPEA and not mentioned here. For details, see the configuration files.

    [UPEA] rrpp enable

  6. Verify the configuration.

    After the preceding configurations are complete and the network becomes stable, run the following commands to verify the configuration. UPEA and PEAGG are used as examples.

    # Run the display rrpp brief command on UPEA. The command output is as follows:

    [UPEA] display rrpp brief
Abbreviations for Switch Node Mode :
M - Master , T - Transit , E - Edge , A - Assistant-Edge

RRPP Protocol Status: Enable
RRPP Working Mode: HW
RRPP Linkup Delay Timer: 0 sec (0 sec default)
Number of RRPP Domains: 2

Domain Index   : 1
Control VLAN   : major 5    sub 6
Protected VLAN : Reference Instance 1
Hello Timer    : 1 sec(default is 1 sec)  Fail Timer : 6 sec(default is 6 sec)

Ring  Ring   Node  Primary/Common           Secondary/Edge           Is
ID    Level  Mode  Port                     Port                     Enabled
----------------------------------------------------------------------------
1     0      T     GigabitEthernet1/0/0     GigabitEthernet2/0/0    Yes

Domain Index   : 2
Control VLAN   : major 10    sub 11
Protected VLAN : Reference Instance 2
Hello Timer    : 1 sec(default is 1 sec)  Fail Timer : 6 sec(default is 6 sec)

Ring  Ring   Node  Primary/Common           Secondary/Edge           Is
ID    Level  Mode  Port                     Port                     Enabled
----------------------------------------------------------------------------
1     0      T     GigabitEthernet1/0/0     GigabitEthernet2/0/0    Yes

    The command output shows that RRPP is enabled on UPEA.

    In Domain 1, the major control VLAN is VLAN 5 and the protected VLANs are VLANs mapping Instance 1. UPEA is a transit node on Ring 1. GigabitEthernet1/0/0 is the primary interface and GigabitEthernet2/0/0 is the secondary interface.

    In Domain 2, the major control VLAN is VLAN 10 and the protected VLANs are VLANs mapping Instance 2. UPEA is a transit node on Ring 1. GigabitEthernet1/0/0 is the primary interface and GigabitEthernet2/0/0 is the secondary interface.

    # Run the display rrpp brief command on PEAGG. The command output is as follows:

    [PEAGG] display rrpp brief
Abbreviations for Switch Node Mode :
M - Master , T - Transit , E - Edge , A - Assistant-Edge

RRPP Protocol Status: Enable
RRPP Working Mode: HW
RRPP Linkup Delay Timer: 0 sec (0 sec default)
Number of RRPP Domains: 2

Domain Index   : 1
Control VLAN   : major 5    sub 6
Protected VLAN : Reference Instance 1
Hello Timer    : 1 sec(default is 1 sec)  Fail Timer : 6 sec(default is 6 sec)

Ring  Ring   Node  Primary/Common           Secondary/Edge           Is
ID    Level  Mode  Port                     Port                     Enabled
----------------------------------------------------------------------------
1     0      M     GigabitEthernet1/0/0     GigabitEthernet2/0/0    Yes

Domain Index   : 2
Control VLAN   : major 10    sub 11
Protected VLAN : Reference Instance 2
Hello Timer    : 1 sec(default is 1 sec)  Fail Timer : 6 sec(default is 6 sec)

Ring  Ring   Node  Primary/Common           Secondary/Edge           Is
ID    Level  Mode  Port                     Port                     Enabled
----------------------------------------------------------------------------
1     0      M     GigabitEthernet2/0/0     GigabitEthernet1/0/0    Yes

    The command output shows that RRPP is enabled on PEAGG.

    In Domain 1, the major control VLAN is VLAN 5, the protected VLAN is the VLAN mapped to Instance 1, and the master node on Ring 1 is PEAGG. GigabitEthernet1/0/0 is the primary interface and GigabitEthernet2/0/0 is the secondary interface.

    In Domain 2, the major control VLAN is VLAN 10, the protected VLAN is the VLAN mapped to Instance 2, and the master node on Ring 1 is PEAGG. GigabitEthernet2/0/0 is the primary interface and GigabitEthernet1/0/0 is the secondary interface.

    # Check detailed information about UPEA in Domain 1. Run the display rrpp verbose domain command on UPEA. The command output is as follows:

    [UPEA] display rrpp verbose domain 1
Domain Index   : 1
Control VLAN   : major 5    sub 6
Protected VLAN : Reference Instance 1
Hello Timer    : 1 sec(default is 1 sec)  Fail Timer : 6 sec(default is 6 sec) 

RRPP Ring      : 1
Ring Level     : 0
Node Mode      : Transit
Ring State     : LinkUp
Is Enabled     : Enable                       Is Active: Yes
Primary port   : GigabitEthernet1/0/0         Port status: UP
Secondary port : GigabitEthernet2/0/0         Port status: UP

    The command output shows that the control VLAN in Domain 1 is VLAN 5, and the protected VLANs are the VLANs mapping Instance 1. UPEA is a transit node in Domain 1 and is in LinkUp state.

    # Check detailed information about UPEA in Domain 2.

    [UPEA] display rrpp verbose domain 2
Domain Index   : 2
Control VLAN   : major 10    sub 11
Protected VLAN : Reference Instance 2
Hello Timer    : 1 sec(default is 1 sec)  Fail Timer : 6 sec(default is 6 sec) 

RRPP Ring      : 1
Ring Level     : 0
Node Mode      : Transit
Ring State     : LinkUp
Is Enabled     : Enable                       Is Active: Yes
Primary port   : GigabitEthernet1/0/0         Port status: UP
Secondary port : GigabitEthernet2/0/0         Port status: UP

    The command output shows that, in Domain 2, the control VLAN is VLAN 10 and the protected VLAN is the VLAN mapped to Instance 2. UPEA is a transit node in Domain 2 and is in LinkUp state.

    Run the display rrpp verbose domain command on PEAGG. The command output is as follows:

    # Check detailed information about PEAGG in Domain 1.

    [PEAGG] display rrpp verbose domain 1
Domain Index   : 1
Control VLAN   : major 5    sub 6
Protected VLAN : Reference Instance 1
Hello Timer    : 1 sec(default is 1 sec)  Fail Timer : 6 sec(default is 6 sec) 

RRPP Ring      : 1
Ring Level     : 0
Node Mode      : Master
Ring State     : Complete
Is Enabled     : Enable                       Is Active: Yes
Primary port   : GigabitEthernet1/0/0         Port status: UP
Secondary port : GigabitEthernet2/0/0         Port status: BLOCKED

    The command output shows that the control VLAN in Domain 1 is VLAN 5, and the protected VLANs are the VLANs mapping Instance 1.

    PEAGG is the master node in Domain 1 and is in Complete state.

    The primary interface is GigabitEthernet1/0/0 and the secondary interface is GigabitEthernet2/0/0.

    # Check detailed information about PEAGG in Domain 2.

    [PEAGG] display rrpp verbose domain 2
Domain Index   : 2
Control VLAN   : major 10    sub 11
Protected VLAN : Reference Instance 2
Hello Timer    : 1 sec(default is 1 sec)  Fail Timer : 6 sec(default is 6 sec) 

RRPP Ring      : 1
Ring Level     : 0
Node Mode      : Master
Ring State     : Complete
Is Enabled     : Enable                       Is Active: Yes
Primary port   : GigabitEthernet2/0/0         Port status: UP
Secondary port : GigabitEthernet1/0/0         Port status: BLOCKED

    The command output shows that, in Domain 2, the control VLAN is VLAN 10, and the protected VLAN is the VLAN mapped to Instance 2.

    PEAGG is the master node in Domain 2 and is in Complete state.

    The primary interface is GigabitEthernet2/0/0 and the secondary interface is GigabitEthernet1/0/0.

Configuration Files

  • UPEA configuration file

    #
sysname UPEA
#
vlan batch 5 to 6 10 to 11 100 to 300
#
rrpp enable
#
stp region-configuration
 instance 1 vlan 5 to 6 100 to 200
 instance 2 vlan 10 to 11 201 to 300
 active region-configuration
#
rrpp domain 1
 control-vlan 5
 protected-vlan reference-instance 1
 ring 1 node-mode transit primary-port GigabitEthernet1/0/0 secondary-port GigabitEthernet2/0/0 level 0
 ring 1 enable
rrpp domain 2
 control-vlan 10
 protected-vlan reference-instance 2
 ring 1 node-mode transit primary-port GigabitEthernet1/0/0 secondary-port GigabitEthernet2/0/0 level 0
 ring 1 enable
#
interface GigabitEthernet1/0/0
 port link-type trunk
 undo port trunk allow-pass vlan 1
 port trunk allow-pass vlan 5 to 6 10 to 11 100 to 300
 stp disable
#
interface GigabitEthernet2/0/0
 port link-type trunk
 undo port trunk allow-pass vlan 1
 port trunk allow-pass vlan 5 to 6 10 to 11 100 to 300
 stp disable
#
return

  • UPEB configuration file

    #
sysname UPEB
#
vlan batch 5 to 6 10 to 11 100 to 300
#
rrpp enable
#
stp region-configuration
 instance 1 vlan 5 to 6 100 to 200
 instance 2 vlan 10 to 11 201 to 300
 active region-configuration
#
rrpp domain 1
 control-vlan 5
 protected-vlan reference-instance 1
 ring 1 node-mode transit primary-port GigabitEthernet1/0/0 secondary-port GigabitEthernet2/0/0 level 0
 ring 1 enable
rrpp domain 2
 control-vlan 10
 protected-vlan reference-instance 2
 ring 1 node-mode transit primary-port GigabitEthernet1/0/0 secondary-port GigabitEthernet2/0/0 level 0
 ring 1 enable
#
interface GigabitEthernet1/0/0
 port link-type trunk
 undo port trunk allow-pass vlan 1
 port trunk allow-pass vlan 5 to 6 10 to 11 100 to 300
 stp disable
#
interface GigabitEthernet2/0/0
 port link-type trunk
 undo port trunk allow-pass vlan 1
 port trunk allow-pass vlan 5 to 6 10 to 11 100 to 300
 stp disable
#
return

  • UPEC configuration file

    #
sysname UPEC
#
vlan batch 5 to 6 10 to 11 100 to 300
#
rrpp enable
#
stp region-configuration
 instance 1 vlan 5 to 6 100 to 200
 instance 2 vlan 10 to 11 201 to 300
 active region-configuration
#
rrpp domain 1
 control-vlan 5
 protected-vlan reference-instance 1
 ring 1 node-mode transit primary-port GigabitEthernet1/0/0 secondary-port GigabitEthernet2/0/0 level 0
 ring 1 enable
rrpp domain 2
 control-vlan 10
 protected-vlan reference-instance 2
 ring 1 node-mode transit primary-port GigabitEthernet1/0/0 secondary-port GigabitEthernet2/0/0 level 0
 ring 1 enable
#
interface GigabitEthernet1/0/0
 port link-type trunk
 undo port trunk allow-pass vlan 1
 port trunk allow-pass vlan 5 to 6 10 to 11 100 to 300
 stp disable
#
interface GigabitEthernet2/0/0
 port link-type trunk
 undo port trunk allow-pass vlan 1
 port trunk allow-pass vlan 5 to 6 10 to 11 100 to 300
 stp disable
#
return

  • PEAGG configuration file

    #
sysname PEAGG
#
vlan batch 5 to 6 10 to 11 100 to 300
#
rrpp enable
#
stp region-configuration
 instance 1 vlan 5 to 6 100 to 200
 instance 2 vlan 10 to 11 201 to 300
 active region-configuration
#
rrpp domain 1
 control-vlan 5
 protected-vlan reference-instance 1
 ring 1 node-mode master primary-port GigabitEthernet1/0/0 secondary-port GigabitEthernet2/0/0 level 0
 ring 1 enable
rrpp domain 2
 control-vlan 10
 protected-vlan reference-instance 2
 ring 1 node-mode master primary-port GigabitEthernet2/0/0 secondary-port GigabitEthernet1/0/0 level 0
 ring 1 enable
#
interface GigabitEthernet1/0/0
 port link-type trunk
 undo port trunk allow-pass vlan 1
 port trunk allow-pass vlan 5 to 6 10 to 11 100 to 300
 stp disable
#
interface GigabitEthernet2/0/0
 port link-type trunk
 undo port trunk allow-pass vlan 1
 port trunk allow-pass vlan 5 to 6 10 to 11 100 to 300
 stp disable
#
return

Relevant Information

Video

Configure RRPP

Translation
简体中文
Download
Updated: 2022-05-23

Document ID: EDOC1000142081

Views: 1016682

Downloads: 880

Average rating:
This Document Applies to these Products

Related Version

Related Documents

Digital Signature File

Digital Signature Authentication Mode
Share
Previous Next

Copyright © 2023 Huawei Technologies Co., Ltd. All rights reserved.

You are going to visit :