No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S12700 V200R010C00 Configuration Guide - Ethernet Switching

This document describes the configuration of Ethernet services, including configuring link aggregation, VLANs, Voice VLAN, VLAN mapping, QinQ, GVRP, MAC table, STP/RSTP/MSTP, SEP, and so on.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Reporting Topology Changes in a Lower-Layer Network - SEP Topology Change Notification

Reporting Topology Changes in a Lower-Layer Network - SEP Topology Change Notification

Context

SEP runs on devices at the access layer. The topology change notification function enables devices to detect topology changes on the upper and lower-layer networks.

If the upper-layer network fails to be notified of the topology change in a SEP segment, the MAC address entries remain unchanged on the upper layer network and user traffic may be interrupted. To ensure uninterrupted traffic forwarding, configure devices on the lower-layer network to report topology changes to the upper-layer network and specify the devices on the upper-layer network that will be notified of topology changes.

NOTE:

Currently, topology changes in a SEP segment can be reported to other SEP segments, STP networks, RRPP networks, VPLS networks, and SmartLink networks.

Switch XGE interfaces connected to the ACU2, ET1D2IPS0S00, ET1D2FW00S00, ET1D2FW00S01 or ET1D2FW00S02 card do not support SEP topology change notification on the VPLS network.

After receiving a topology change notification from a lower-layer network, a device on the upper-layer network sends TC packets to instruct other devices on the upper-layer network to clear original MAC addresses and learn new MAC addresses after the topology of the lower-layer network changes. This ensures uninterrupted traffic forwarding.

Procedure

  1. Run:

    system-view

    The system view is displayed.

  2. Run:

    sep segment segment-id

    A SEP segment is created and the view of the SEP segment is displayed.

  3. Run:

    tc-notify { segment { segment-id1 [ to segment-id2 ] } &<1-10> | stp | rrpp | smart-link send-packet vlan vlan-id | vpls }

    The topology change of the specified SEP segment is reported to another SEP segment or a network running other ring protocols such as STP or RRPP.

    By default, the topology change of a SEP segment is not reported.

Follow-up Procedure

In the networking scenario where three or more SEP ring networks exist, when a topology change notification is sent through multiple links, the upper-layer network will receive it multiple times. This reduces packet processing efficiency on the upper-layer network. Therefore, topology change notifications need to be suppressed. Suppressing topology change notifications frees the upper-layer network from processing multiple duplicate packets and protects the devices in the SEP segment against topology change notification attacks.

Run the tc-protection interval interval-value command in the SEP segment view to set the interval for suppressing topology change notifications.

By default, the interval for suppressing topology change notifications is 2s, and three topology change notifications with different source addresses are processed within 2s.

NOTE:
  • In the networking scenario where three or more SEP ring networks exist, the tc-protection interval interval-value command must be run. If this command is not run, the default interval for suppressing topology change notifications is used.

  • A longer interval ensures stable SEP operation but reduces convergence performance.

Translation
Download
Updated: 2019-08-21

Document ID: EDOC1000142081

Views: 269122

Downloads: 416

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next