No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S12700 V200R010C00 Configuration Guide - Ethernet Switching

This document describes the configuration of Ethernet services, including configuring link aggregation, VLANs, Voice VLAN, VLAN mapping, QinQ, GVRP, MAC table, STP/RSTP/MSTP, SEP, and so on.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Licensing Requirements and Limitations for LDT and LBDT

Licensing Requirements and Limitations for LDT and LBDT

Involved Network Elements

Other network elements are not required.

Licensing Requirements

LDT and LBDT are basic features of a switch and are not under license control.

Version Requirements

Table 20-4  Products and versions supporting LDT and LBDT

Product

Product Model

Software Version

S12700

S12708, S12712

V200R005C00, V200R006C00, V200R007C00, V200R007C20, V200R008C00, V200R009C00, V200R010C00, V200R011C10

S12710

V200R010C00, V200R011C10

S12704

V200R008C00, V200R009C00, V200R010C00, V200R011C10

NOTE:
To know details about software mappings, see Hardware Query Tool.

Feature Limitations of LDT

  • In V200R008C00 and earlier versions, LDT does not take effect in dynamic VLANs. In V200R008C00 and later versions, the LDT-enabled switch can detect loops in dynamic VLANs, but the Quitvlan action is invalid for dynamic VLANs.

  • LDT and LBDT cannot be configured simultaneously.

  • The switch enabled with LDT needs to send a large number of detection packets to detect loops, occupying system resources. Disable LDT if loops do not need to be detected.

  • LDT performance is lowered when loops occur on multiple interfaces in multiple VLANs. This is due to the limitations of security policies and processing capability of the CPU. The more VLANs and interfaces involved, the lower the performance is, especially the performance of the standby chassis in the cluster. In this case, you need to eliminate the loops manually.

  • LDT cannot be used with ring network technologies including ERPS, RRPP, SEP, Smart Link, STP, RSTP, MSTP, and VBST. Do not configure ring network technologies on an interface of the LDT-enabled VLAN. If LDT has been enabled globally and a ring network technology needs to be configured on an interface, disable LDT on that interface first.

  • The blocked ports of LDT cannot block GVRP packets. To ensure that GVRP runs normally and prevent GVRP loops, do not enable GVRP on the blocked port of LDT.

Feature Limitations of LBDT

  • In V200R008C00 and earlier versions, LBDT does not take effect in dynamic VLANs. In V200R008C00 and later versions, the LBDT-enabled switch can detect loops in dynamic VLANs, but the Quitvlan action is invalid for dynamic VLANs.

  • LBDT and LDT cannot be configured simultaneously.

  • LBDT requires that the device should send a large number of detection packets to detect loops, occupying system resources. Therefore, disable LBDT if loops do not need to be detected.

  • LBDT cannot be configured on an Eth-Trunk or its member interfaces.

  • The blocked ports of LBDT cannot block GVRP packets. To ensure that GVRP runs normally and prevent GVRP loops, do not enable GVRP on the blocked port of LBDT.
Translation
Download
Updated: 2019-08-21

Document ID: EDOC1000142081

Views: 275150

Downloads: 421

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next