No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search


To have a better experience, please upgrade your IE browser.


S12700 V200R010C00 Configuration Guide - Ethernet Switching

This document describes the configuration of Ethernet services, including configuring link aggregation, VLANs, Voice VLAN, VLAN mapping, QinQ, GVRP, MAC table, STP/RSTP/MSTP, SEP, and so on.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Licensing Requirements and Limitations for Voice VLAN

Licensing Requirements and Limitations for Voice VLAN

Involved Network Elements

Other network elements are not required.

Licensing Requirements

The voice VLAN is a basic feature of a switch and is not under license control.

Version Requirements

Table 9-1  Products and versions supporting the voice VLAN


Product Model

Software Version


S12708, S12712

V200R005C00, V200R006C00, V200R007C00, V200R007C20, V200R008C00, V200R009C00, V200R010C00, V200R011C10


V200R010C00, V200R011C10


V200R008C00, V200R009C00, V200R010C00, V200R011C10

To know details about software mappings, see Hardware Query Tool.

Feature Limitations

  • The switch XGE interface connected to ET1D2IPS0S00, ET1D2FW00S00, ET1D2FW00S01, ET1D2FW00S02, or ACU2 does not support voice VLAN.

  • VLAN 1 cannot be configured as a voice VLAN.

  • To transmit different services, ensure that the voice VLAN and default VLAN on an interface are different VLANs.

  • Only one VLAN on an interface can be configured as a voice VLAN at a time.

  • After a voice VLAN is configured on an interface, VLAN mapping, VLAN stacking, or traffic policies cannot be configured on the interface.

  • Do not set the VLAN ID to 0 on an IP phone.
  • X series cards on modular switches does not support the automatic mode.
  • In auto mode, access, negotiation-auto, or negotiation-desirable interfaces cannot be added to a voice VLAN. To add the interface to the voice VLAN, run the port link-type command to change the link type of the interface to trunk or hybrid.
  • When an IP phone is connected to a switch through the OUI-based voice VLAN, disable LLDP on the interface. If LLDP is enabled on the interface, the switch will allocate a voice VLAN ID to the IP phone. The IP phone sends tagged packets to the switch, whereas the switch sends untagged packets to the IP phone. As a result, the IP phone cannot go online.
  • The automatic mode takes effect only when the voice-vlan remark-mode mac-address command is configured to increase the priority of voice packets based on MAC addresses and the voice-vlan enable command without include-untagged specified is configured to enable voice VLAN on the interface.
  • When the remark (user group view) and voice-vlan remark commands are used together to modify the user packet priority, if the services conflict:

    • For X series cards, the priority configured using the remark (user group view) command takes effect.
    • For the non-X series cards, the priority configured using the voice-vlan remark command takes effect.
Updated: 2019-08-21

Document ID: EDOC1000142081

Views: 270182

Downloads: 420

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Previous Next