No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S12700 V200R010C00 Configuration Guide - Reliability

This document describes the configuration of BFD, DLDP, VRRP, SmartLink, CFM, EFM, Y.1731 and MAC swap loopback to ensure reliability on the device.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring Multi-Hop BFD

Configuring Multi-Hop BFD

Pre-configuration Tasks

Multi-hop BFD fast detects faults on the indirectly connected link.

Before configuring multi-hop BFD, configure a routing protocol to ensure reachability at the network layer.

Configuration Process

Figure 2-16  Multi-hop BFD configuration process

Procedure

  1. Run:

    system-view

    The system view is displayed.

  2. Run:

    bfd

    BFD is enabled globally and the BFD view is displayed.

    By default, BFD is disabled globally.

  3. (Optional) Run:

    multi-hop destination-port { 3784 | 4784 }

    The destination port number for a multi-hop BFD session is configured.

    By default, destination port 3784 is used in multi-hop BFD control packets.

  4. Run:

    quit

    Return to the system view.

  5. Run any of the following commands based on the link type.

    • IPv4 links:

      Run:

      bfd session-name bind peer-ip ip-address [ vpn-instance vpn-name ] [ source-ip ip-address ]

      The binding information of the BFD session is configured.

      By default, no BFD session is created.

      NOTE:
      • When creating the BFD session, the system checks only the format of the IP address rather than its correctness. The BFD session cannot be established if an incorrect peer IP address or source IP address is bound.

      • During BFD session creation, the value of peer-ip or source-ip cannot be the IP address of a GRE tunnel interface.

      • During BFD session creation, the outbound interface specified by peer-ip cannot be the tunnel interface.

      • If the peer IP address of a multi-hop BFD session is the same as a 32-bit destination address of an LDP LSP/static LSP, the BFD session is associated with this LSP. That is, when the BFD session detects a fault, LSP protection switchover is performed.

    • IPv6 links:

      Run:

      bfd session-name bind peer-ipv6 ipv6-address [ vpn-instance vpn-instance-name ] [ source-ipv6 ipv6-address ]

      The binding information of the BFD6 session is configured.

      • When creating a BFD6 session, bind the session to the peer IPv6 address. In addition, the configuration of the BFD6 session cannot be modified after the session is created.
      • If the specified peer IPv6 address is a local address of the IPv6 link, bind the BFD6 session to an interface. That is, you can create only a single-hop BFD6 session. Otherwise, error information is displayed.
      • When configuring the BFD6 session, the system checks only the format of the peer IPv6 address rather than its correctness. A BFD6 session cannot be established if an incorrect peer IPv6 address or source IPv6 address is bound.
      • During BFD6 session creation, the value of peer-ipv6 or source-ipv6 cannot be the IPv6 address of a GRE tunnel interface.

  6. Run:

    discriminator local discr-value

    The local discriminator is set.

  7. Run:

    discriminator remote discr-value

    The remote discriminator is set.

    NOTE:

    The local discriminator of the local system must be the same as the remote discriminator of the remote system; the remote discriminator of the local system must be the same as the local discriminator of the remote system. Otherwise, BFD sessions cannot be established. After the local discriminator and the remote discriminator are configured, you cannot modify them.

  8. Run:

    commit

    The configuration is committed.

Translation
Download
Updated: 2019-04-20

Document ID: EDOC1000142090

Views: 82729

Downloads: 104

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next