No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S12700 V200R010C00 Configuration Guide - WLAN-AC

This document describes native AC (hereinafter referred to as WLAN AC) configuration procedures and provides configuration examples.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring Parameters for an AP's Wired Interface

Configuring Parameters for an AP's Wired Interface

Context

You can configure the wired interface on an MPP to connect to the AC or configure the wired interface on an AP to deploy a Layer 2 network or directly associate with STAs.

On Mesh networks, an AP wired interface can work in the following modes:

  • root mode: The wired interface that connects the MPP to the AC must work in root mode.
  • endpoint mode: When the wired interface of an AP works in endpoint mode, the AP's wired interface can directly connect to a STA or be used to deploy Layer 2 networks.

Procedure

  1. Run:

    system-view

    The system view is displayed.

  2. Run:

    wlan

    The WLAN view is displayed.

  3. Run:

    wired-port-profile name profile-name

    An AP wired port profile is created and the AP wired port profile view is displayed.

    By default, the system provides the AP wired port profile default.

  4. Run:

    mode { root | endpoint }

    A working mode is configured for the AP's wired interface.

    By default,
    • On a common AP: Its GE interfaces work in root mode, Ethernet interfaces in endpoint mode, and Eth-Trunk interfaces in root mode.
    • On a central AP: Its uplink GE interfaces in root mode and downlink GE interfaces work in middle mode.
    • On an R230D: Its Ethernet interface works in root mode.
    • On an R240D: Its Ethernet interface works in endpoint mode and GE interface in root mode.
    • On an R250D, R250D-E, AP2050DN, and AP2050DN-E: Their uplink GE interfaces work in root mode and downlink GE interfaces in endpoint mode.
    NOTE:

    After changing the working mode of an AP's wired interface, run the ap-reset command to reset the AP for the configuration to take effect.

  5. Run:

    vlan { tagged | untagged } { vlan-id1 [ to vlan-id2 ] } &<1-10>

    The VLAN to which the AP's wired interface is added is specified.

    By default, an AP wired interface allows packets from all VLANs to pass. The wired interface is added to VLAN 1 in untagged mode and to other VLANs in tagged mode.

    When an AT connects to an MPP through a Mesh link, run the vlan { tagged | untagged } { vlan-id1 [ to vlan-id2 ] } &<1-10> command to add the AP's wired interface to the VLAN used by the AT; otherwise, the AT cannot communicate with the AP. If the service VLAN of the AP is the same as the VLAN used by the AT, you do not need to run the command because the AP's wired interface automatically joins the VLAN after the AP receives the service VLAN configuration from the AC.

    NOTE:

    An AP wired interface can be added to a maximum of 256 VLANs.

  6. Run:

    vlan pvid vlan-id

    A PVID is configured for the AP's wired interface.

    By default, no PVID is configured for an AP wired interface.

  7. Run:

    user-isolate { all | l2 }

    User isolation is enabled on the AP's wired interface.

    By default, user isolation is disabled on an AP's wired interface.

Follow-up Procedure

Run the wired-port-profile profile-name interface-type interface-number command in the AP group view or AP view to bind the specified AP wired port profile to the AP's wired interface.

Translation
Download
Updated: 2019-08-21

Document ID: EDOC1000142094

Views: 149454

Downloads: 128

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next