No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S12700 V200R010C00 Configuration Guide - WLAN-AC

This document describes native AC (hereinafter referred to as WLAN AC) configuration procedures and provides configuration examples.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring Priority Mapping

Configuring Priority Mapping

Pre-configuration Tasks

Before configuring priority mapping, perform the task of WLAN Service Configuration.

Procedure

  1. Run:

    system-view

    The system view is displayed.

  2. Run:

    wlan

    The WLAN view is displayed.

  3. Run:

    traffic-profile name profile-name

    A traffic profile is created and the traffic profile view is displayed.

    By default, the system provides the traffic profile default.

  4. Configure priority mapping as required.

    • Configure priority mapping for packets sent to an AP from upper-layer devices.

      1. Run the priority-map downstream trust { dot1p | dscp } command to configure a trusted priority type used in mapping from 802.3 packets to 802.11 packets.

        By default, the DSCP priority is used in mapping from 802.3 packets to 802.11 packets when packets are sent to an AP from upper-layer devices.

      2. Configure priority mapping.

        • When the DSCP priority is specified as the trusted priority type, perform the following configuration:

          Run the priority-map downstream dscp { dscp-value1 [ to dscp-value2 ] } &<1-10> dot11e dot11e-value command to configure mapping from the DSCP priority of 802.3 packets to the user priority of 802.11 packets when packets are sent to an AP from upper-layer devices.

          Table 10-9 describes the default mapping from the DSCP priority of 802.3 packets to the user priority of 802.11 packets.
          Table 10-9  Default mapping from the DSCP priority of 802.3 packets to the user priority of 802.11 packets

          DSCP

          UP

          0-7

          0

          8-15

          1

          16-23

          2

          24-31

          3

          32-39

          4

          40-47

          5

          48-55

          6

          56-63

          7

        • When the 802.1p priority is specified as the trusted priority type, perform the following configuration:

          Run the priority-map downstream dot1p { dot1p-value1 [ to dot1p-value2 ] } &<1-7> dot11e dot11e-value command to configure mapping from the 802.1p priority of 802.3 packets to the user priority of 802.11 packets when packets are sent to an AP from upper-layer devices.

          By default, 802.1p priority 0 of 802.3 packets maps to user priority 0 of 802.11 packets, 802.1p priority 1 to user priority 1, and similarly, 802.1p priority 7 to user priority 7.

    • Configure tunnel priority mapping when data packets are sent from APs to an AC.

      NOTE:

      The tunnel priority mapping is applicable to scenarios where data packets are sent in tunnel forwarding mode.

      1. Run the priority-map tunnel-upstream trust { dot11e | dscp } command to configure a trusted priority type used in mapping from 802.11 packets to tunnel packets.

        By default, the 802.11e priority is used in mapping from 802.11 packets to tunnel packets when packets are sent to the AC from an AP.

      2. Configure tunnel priority mapping.

        • When the 802.11 priority is specified as the trusted priority type, perform the following configuration:

          Run the priority-map tunnel-upstream dot11e { dot11e-value1 [ to dot11e-value2 ] } &<1-7> dscp dscp-value command to configure mapping from the user priority of 802.11 packets to the DSCP priority of tunnel packets.

          Table 10-10 describes the default mapping from the user priority of 802.11 packets to the DSCP priority of tunnel packets.
          NOTE:
          The CAPWAP header refers to the tunnel header.
          Table 10-10  Default mapping from the user priority of 802.11 packets to the DSCP priority in the CAPWAP header

          User Priority of 802.11 Packets

          DSCP Priority in the CAPWAP Header

          0

          0

          1

          8

          2

          16

          3

          24

          4

          32

          5

          40

          6

          48

          7

          56

          Run the priority-map tunnel-upstream dot11e { dot11e-value1 [ to dot11e-value2 ] } &<1-7> dot1p dot1p-value command to configure mapping from the user priority of 802.11 packets to the 802.1p priority of tunnel packets when packets are sent to an AC from an AP.

          By default, user priority 0 of 802.11 packets maps to 802.1p priority 0 of tunnel packets, user priority 1 to 802.1p priority 1, and similarly, user priority 7 to 802.1p priority 7.

        • When the DSCP priority is specified as the trusted priority type, perform the following configuration:

          Run the priority-map tunnel-upstream dscp { dscp-value [ to dscp-value1 ] } &<1-10> tunnel-dscp dscp-value2 command to configure mapping from the DSCP priority of 802.11 packets to the DSCP priority of tunnel packets.

          By default, DSCP priority 1 of 802.11 packets maps DSCP priority 1 of tunnel packets, DSCP priority 2 of 802.11 packets maps DSCP priority 2 of tunnel packets, and so on. DSCP priority 63 of 802.11 packets maps DSCP priority 63 of tunnel packets.

          Run the priority-map tunnel-upstream dscp { dscp-value1 [ to dscp-value2 ] } &<1-10> dot1p dot1p-value command to configure mapping from the DSCP priority of 802.11 packets to the 802.1p priority of tunnel packets when packets are sent to an AC from an AP.

          Table 10-11 describes the default mapping from DSCP priorities of 802.11 packets to 802.1p priorities of tunnel packets.
          NOTE:
          The CAPWAP header refers to the tunnel header.
          Table 10-11  Default mapping from DSCP priorities of 802.11 packets to 802.1p priorities of in CAPWAP headers

          DSCP Priority of 802.11 Packets

          802.1p Priority in the CAPWAP Header

          0-7

          0

          8-15

          1

          16-23

          2

          24-31

          3

          32-39

          4

          40-47

          5

          48-55

          6

          56-63

          7

  5. Run:

    quit

    Return to the WLAN view.

  6. Run:

    vap-profile name profile-name

    The VAP profile view is displayed.

  7. Run:

    traffic-profile profile-name

    The traffic profile is bound to the VAP profile.

    By default, the traffic profile default is bound to a VAP profile.

  8. Run:

    quit

    Return to the WLAN view.

  9. Run:

    commit { all | ap-name ap-name | ap-id { ap-id1 [ to ap-id2 ] } &<1-10> }

    Configurations are delivered to APs.

Verifying the Configuration

  • Run the display traffic-profile { all | name profile-name } command to check the priority mapping configuration in a traffic profile.

Translation
Download
Updated: 2019-08-21

Document ID: EDOC1000142094

Views: 139750

Downloads: 126

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next