No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S12700 V200R010C00 Configuration Guide - WLAN-AC

This document describes native AC (hereinafter referred to as WLAN AC) configuration procedures and provides configuration examples.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring a Mesh Profile

Configuring a Mesh Profile

Context

On a vehicle-ground fast link handover network shown in Figure 16-9, Mesh roles of the vehicle-mounted AP and trackside AP are MP and MPP respectively.

Figure 16-9  Networking diagram of vehicle-ground fast link handovers

NOTE:

After Mesh is enabled on a vehicle-mounted AP, the Mesh role of the AP is fixed as mesh-node (MP).

Procedure

  1. Run:

    system-view

    The system view is displayed.

  2. Run:

    wlan

    The WLAN view is displayed.

  3. Run:

    mesh-profile name profile-name

    A Mesh profile is created, and the Mesh profile view is displayed.

    By default, the system provides the Mesh profile default.

  4. Run:

    mesh-id name

    A Mesh ID is configured. Mesh nodes use a Mesh ID to identify connections between them.

    By default, the Mesh ID of a Mesh profile is HUAWEI-WLAN-MESH.

  5. Run:

    security-profile profile-name

    A security profile is bound to the Mesh profile.

    By default, the security profile default-mesh is bound to a Mesh profile.

    NOTE:

    By default, the system provides the Mesh profile default. Both the default Mesh profile default and a self-defined Mesh profile have the security profile default-mesh referenced by default. In the security profile default-mesh, the security policy is set to WPA2+PSK+AES and the security key to huawei_secmesh. If the default security profile default-mesh is used, you are advised to change the security key of the profile to ensure security.

  6. Run:

    mesh-handover-profile profile-name

    A Mesh handover profile is bound to the Mesh profile.

    By default, no Mesh handover profile is bound to a Mesh profile.

  7. (Optional) Improve channel usage efficiency.

    1. Run the beacon-2g-rate beacon-2g-rate command to set the transmit rate of 2.4 GHz Beacon frames.

      By default, the transmit rate of 2.4 GHz Beacon frames is 1 Mbit/s.

    2. Run the beacon-5g-rate beacon-5g-rate command to set the transmit rate of 5 GHz Beacon frames.

      By default, the transmit rate of 5 GHz Beacon frames is 6 Mbit/s.

  8. (Optional) Run:

    max-link-number link-num

    The maximum number of Mesh links allowed on an AP is configured.

    By default, a maximum of eight mesh links can be established between APs.

  9. (Optional) Run:

    link-rssi-threshold threshold-value

    The RSSI threshold of a Mesh link is configured. When the minimum RSSI of all Mesh links on the optimal route to the current MPP is lower than the RSSI threshold of a Mesh link, the MP reselects Mesh links.

    By default, the RSSI threshold of a mesh link is -75 dBm. After the FWA mode is enabled in a Mesh profile, the RSSI threshold of a Mesh link is fixed as -90 dBm.

  10. (Optional) Run:

    link-report-interval report-interval

    The interval at which an MP reports Mesh link information to an AC is specified.

    By default, an MP reports Mesh link information to the AC at an interval of 30 seconds.

  11. (Optional) Run:

    dhcp trust port

    A DHCP trusted port is enabled in the Mesh profile.

    By default, a DHCP trusted port is enabled in a Mesh profile.

    NOTE:

    After a DHCP trusted port is enabled in a Mesh profile and the Mesh profile is applied to an AP, the AP receives the DHCP OFFER, ACK, and NAK packets sent by authorized DHCP servers and forwards the packets to STAs so that the STAs can obtain valid IP addresses and go online.

  12. Run:

    quit

    Return to the WLAN view.

  13. Run:

    quit

    Return to the system view.

  14. Run:

    interface wlan-radio wlan-radio-number

    The radio interface view is displayed.

  15. Run:

    mesh-profile profile-name

    The Mesh profile is bound to the AP radio.

    By default, no Mesh profile is bound to an AP radio.

Translation
Download
Updated: 2019-08-21

Document ID: EDOC1000142094

Views: 149262

Downloads: 128

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next