No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S12700 V200R010C00 Configuration Guide - WLAN-AC

This document describes native AC (hereinafter referred to as WLAN AC) configuration procedures and provides configuration examples.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring Bluetooth Terminal Location

Configuring Bluetooth Terminal Location

Pre-configuration Tasks

Before configuring Bluetooth Terminal location, perform the tasks listed in the following table.

Table 19-3  Pre-configuration tasks

Task

Description

Create an AP group

Each AP will be added and can be added to only one AP group. An AP group is usually used to provide the same configurations for multiple APs. By default, the system has an AP group default. To create an AP group, execute this task. For details, see Creating an AP Group.

Configure an AP to go online

Configure a DHCP server

To go online normally, APs and STAs must obtain IP addresses. You can configure an AC as a DHCP server or use an independent DHCP server to allocate IP addresses to APs and STAs. For details, see Configuring a DHCP Server.

Configure network interconnections

To enable APs and STAs to obtain IP addresses, APs to discover the AC and go online on the AC, and STAs to access the network, configure interconnections between network devices. For details, see Configuring Network Interconnections.

Configure country codes

Correct country code configuration ensures that radio attributes of APs comply with laws and regulations of countries and regions to which the APs are delivered. For details, see Configuring Country Codes.

Configure a source interface

Before an AP establishes a CAPWAP tunnel with an AC, a source interface or source address must be specified for the AC. For details, see Configuring a Source Interface.

Add APs

You can add APs in any of the following modes:
  • Importing APs offline.
  • Configuring AC to automatically discover an AP.
  • Manually confirming APs added to the list of unauthorized APs.
Adding an AP offline is recommended when the MAC address or SN of the AP is already learned. For details, see Adding APs.

Procedure

  1. Run:

    system-view

    The system view is displayed.

  2. Run:

    wlan

    The WLAN view is displayed.

  3. Run:

    ble-profile name profile-name

    A BLE profile is created.

    By default, no BLE profile is created.

  4. Run:

    sniffer enable 

    The Bluetooth monitoring function of an AP's built-in Bluetooth module is enabled.

    By default, the Bluetooth monitoring function of an AP's built-in Bluetooth module is disabled.

  5. Configure the Bluetooth broadcast function for an AP's built-in Bluetooth module.

    NOTE:
    • If an independent Bluetooth device is deployed on a WLAN, this step is optional. If no independent Bluetooth device is deployed on a WLAN, this step is mandatory.
    • Only the AP4050DN-E supports the Bluetooth broadcast function.

    1. Run:

      broadcaster enable

      The Bluetooth broadcast function of an AP's built-in Bluetooth module is enabled.

      By default, the Bluetooth broadcast function of an AP's built-in Bluetooth module is disabled.

    2. Run:

      tx-power tx-power-value

      The transmit power is set for the built-in Bluetooth module of an AP.

      By default, the transmit power of an AP's built-in Bluetooth module is 0 dBm.

    3. Run:

      broadcasting-content { uuid { uuid-character-string uuid-value | uuid-hex uuid-value } | major { major-character-string major-value | major-hex major-value | major-decimal major-value } | minor { minor-character-string minor-value | minor-hex minor-value | minor-decimal minor-value } | reference-rssi reference-rssi-value }*

      The content of BLE broadcast frames sent by an AP's built-in Bluetooth module is configured.

      By default, the UUID, Major, and Minor fields in a BLE broadcast frame sent by an AP's built-in Bluetooth module are null, and the RSSI calibration value is -65 dBm.

      The RSSI calibration value in a BLE broadcast frame is set based on the actual measurement result.

    4. Run:

      broadcasting-interval broadcasting-interval-value

      The interval for an AP's built-in Bluetooth module to send BLE broadcast frames is set.

      By default, the built-in Bluetooth module of an AP sends BLE broadcast frames at an interval of 500 ms.

  6. Run:

    quit

    Return to the WLAN view.

  7. Enter the AP view or AP group view.

    • Run the ap-group name group-name command to enter the AP group view.
    • Run the ap-id ap-id, ap-mac ap-mac, or ap-name ap-name command to enter the AP view.

  8. (Optional) Run:

    ble-profile profile-name

    A BLE profile is applied to an AP or AP group.

    By default, no BLE profile is bound to an AP group or AP.

  9. Run:

    quit

    Return to the WLAN view.

  10. (Optional) Run:

    ble low-power-threshold low-power-threshold

    The low power alarm threshold for BLE devices is set.

    By default, the low power alarm threshold of BLE devices is 20%.

  11. (Optional) Run:

    ble monitoring-list mac mac-address1 [ to mac-address2 ]

    A specified Bluetooth device is added to the monitoring list on the built-in Bluetooth module of an AP

    By default, no Bluetooth devices are added to the monitoring list.

    When a Bluetooth device in the monitoring list is offline or has insufficient battery power, an alarm is triggered on the AC accordingly. If a Bluetooth device is not in the monitoring list, no such alarm will be triggered on the AC.

  12. Run:

    commit { all | ap-name ap-name | ap-id { ap-id1 [ to ap-id2 ] } &<1-10> }

    Configurations are delivered to APs.

Verifying the Configuration

  • Run the display ble-profile { all | name profile-name } command to check configuration and reference information about a BLE profile.

  • Run the display references ble-profile name profile-name command to check reference information about a BLE profile.

Follow-up Procedure

After configuring Bluetooth location, you need to perform the following operations to check location results on a location server.
  • Configure Bluetooth location parameters on the location server.
  • Configure the location server to communicate with the app server.
  • Install a Bluetooth location app (usually provided by a location server vendor) on a Bluetooth terminal (such as a mobile phone). Enable Bluetooth, and enable Wi-Fi or mobile cellular networks, to ensure that the Bluetooth terminal can access a network and send information about scanned BLE devices to the location server.
Translation
Download
Updated: 2019-08-21

Document ID: EDOC1000142094

Views: 138953

Downloads: 126

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next