No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S12700 V200R010C00 Configuration Guide - WLAN-AC

This document describes native AC (hereinafter referred to as WLAN AC) configuration procedures and provides configuration examples.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring Communication Parameters Between an AP and an IoT Card

Configuring Communication Parameters Between an AP and an IoT Card

Context

An AP communicates with an IoT card through a serial port. Each IoT card interface uses independent serial communication parameters and framing parameters. The serial communication parameters and framing parameters can be set in a serial profile.

Procedure

  1. Run:

    system-view

    The system view is displayed.

  2. Run:

    wlan

    The WLAN view is displayed.

  3. Run:

    serial-profile name profile-name

    A serial profile is created and the serial profile view is displayed.

    By default, serial profile preset-enjoyor-toeap is bound to an IoT card interface.

    Self-defined serial profiles cannot start with preset-.

  4. Set serial communication parameters.
    1. Run the speed speed-value command to set the baud rate.

      By default, the baud rate is 115200 bit/s.

    2. Run the parity { none | odd | even | mark | space } command to set the parity bit.

      By default, the parity bit is none on an IoT card slot.

    3. Run the stopbits { 1 | 2 } command to set the stop bit.

      The default stop bit is 1.

  5. Set serial framing parameters.

    • Set framing parameters based on fixed frames.
      1. Run the frame-format fixed-length command to configure a fixed-length frame format.
      2. Run the frame-length frame-length-value command to set the frame length.

      By default, the frame format is frame-start-stop, the frame length is 512 bytes.

    • Set framing parameters based on start and stop flags of frames.
      1. Run the frame-format frame-start-stop command to configure start and stop flags of frames.
      2. Run the frame-length frame-length-value command to set the frame length.
        NOTE:

        The frame length must be at least 2 bytes.

      3. Run the frame-start frame-start-value command to configure the frame start flag.
      4. Run the frame-stop frame-stop-value command to configure the frame stop flag.

      By default, the frame format is frame-start-stop, the frame length is 512 bytes, the frame start flag is aa, and the frame stop flag is 7e.

  6. Run:

    quit

    Return to the WLAN view.

  7. Apply configurations to an IoT card interface.

    • Bind a serial profile in the IoT card interface view of an AP group.
      1. Run the ap-group name group-name command to enter the AP group view.
      2. Run the card card-number command to enter the IoT card interface view.
      3. Run the serial-profile profile-name command to bind a serial profile.

        By default, serial profile preset-enjoyor-toeap is bound to the IoT card interface view of an AP group.

    • Bind a serial profile in the IoT card interface view of an AP.
      1. Run the ap-id ap-id, ap-mac ap-mac, or ap-name ap-name command to enter the AP view.
      2. Run the card card-number command to enter the IoT card interface view.
      3. Run the serial-profile profile-name command to bind a serial profile.

        By default, no serial profile is bound to the IoT card interface view of an AP.

  8. Run:

    quit

    Return to the WLAN view.

  9. Run:

    commit { all | ap-name ap-name | ap-id { ap-id1 [ to ap-id2 ] } &<1-10> }

    Configurations are delivered to APs.

Translation
Download
Updated: 2019-04-20

Document ID: EDOC1000142094

Views: 120507

Downloads: 119

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next