No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S12700 V200R010C00 Configuration Guide - WLAN-AC

This document describes native AC (hereinafter referred to as WLAN AC) configuration procedures and provides configuration examples.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Licensing Requirements and Limitations for WLAN Tag Location

Licensing Requirements and Limitations for WLAN Tag Location

Involved Network Elements

AP
  • APs mentioned in this document are Huawei AP products. You are advised to use Huawei APs to connect to the AC.
  • You can run the display ap-type all command to check the default AP types supported by the device.
  • When central APs and RUs are used, ensure that their versions are the same. For example, if the central AP version is V200R007C10, the RU version must be V200R007C10.
Table 17-1  Mapping between switch versions and AP versions

Product Software Version

AP Software Version

V200R011C10

V200R008C10

V200R008C00

V200R007C20

V200R007C10

V200R006C20

V200R006C10

V200R010C00

V200R007C10

V200R006C20

V200R006C10

V200R009C00

V200R006C20

V200R006C10

V200R007C20

V200R006C10

V200R008C00

V200R005C30

V200R005C20

V200R005C10

V200R007C00

V200R005C20

V200R005C10

V200R006

V200R005C00

V200R005

V200R005C00

Location server
  • Computes the RFID tag location using a location algorithm (for example, three-point positioning) after receiving the location information and provides the computed data to user systems, including the system management software and image software.

Licensing Requirements

When an X series card is used as a WLAN AC, the number of online APs supported by the X series card is controlled by licenses. The X series card supports a maximum of 16 online APs. To increase the number of online APs supported by the card, apply for and purchase a license from the agent.
  • AP resource license-16AP for WLAN access controller
  • AP resource license-64AP for WLAN access controller
  • AP resource license-128AP for WLAN access controller
  • AP resource license-512AP for WLAN access controller

For details about how to apply for a license, see S Series Switch License Use Guide.

Version Requirements

Table 17-2  Products and minimum version supporting WLAN location
Product Minimum Version Required
S12708/S12712 V200R005

S12704

V200R008

S12710

V200R010

Feature Limitations

WLAN Location of AeroScout Tags and AeroScout MUs
  • The AP9330DN does not support Tag location.
  • The AP3010DN-AGN, AP6310SN-GN, and AP9330DN do not support AeroScout MU location.
  • When configuring the AC as the destination to which the AP reports location information:
    • Configure the port number used by the AC to communicate with the AeroScout location server.
    • Ensure that the port number configured on the AeroScout location server is the same as that used by AC to communicate with the AeroScout location server.
  • When configuring the AeroScout location server as the destination to which the AP reports location information, ensure that the port number used by the AP to report location information is the same as that configured on the AeroScout location server.
  • The port number used by the AP to report location information cannot be the same as that used by the AC to communicate with the location server.
  • If the location server runs the Linux system and has URPF enabled, the server must be able to successfully ping the source IP address that the AC uses to send packets.
WLAN Location of Ekahau Tags
  • The AP9330DN does not support Tag location.
  • When configuring the AC as the destination to which the AP reports location information:
    • Configure the port number used by the AC to communicate with the Ekahau location server and the IP address of the Ekahau location server on the AC.
    • Ensure that the port number configured on the Ekahau location server is the same as that used by AC to communicate with the Ekahau location server.
  • When configuring the Ekahau location server as the destination to which the AP reports location information, ensure that the port number used by the AP to report location information is the same as that configured on the Ekahau location server.
  • The port number used by the AP to report location information cannot be the same as that used by the AC to communicate with the location server.
  • If the location server runs the Linux system and has URPF enabled, the server must be able to successfully ping the source IP address that the AC uses to send packets.
Translation
Download
Updated: 2019-08-21

Document ID: EDOC1000142094

Views: 137125

Downloads: 123

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next