No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S12700 V200R010C00 Configuration Guide - WLAN-AC

This document describes native AC (hereinafter referred to as WLAN AC) configuration procedures and provides configuration examples.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring AP Indicators

Configuring AP Indicators

Context

Different states of AP indicators reflect different meanings, thereby facilitating installation and management. Configuring meanings reflected by blinking of the Wireless indicator on APs helps installation personnel to know the current signal strength or traffic status in real time. However, blinking indicators of indoor APs deployed in hospitals and hotels may affect people's nighttime rest. Therefore, you can turn off AP indicators after APs are installed and run properly.

Procedure

  1. Run:

    system-view

    The system view is displayed.

  2. Run:

    wlan

    The WLAN view is displayed.

  3. Run:

    ap-system-profile name profile-name

    An AP system profile is created, and the AP system profile view is displayed.

    By default, the system provides the AP system profile default.

  4. Run:

    led off [ time-range time-range-name ]

    AP indicators are configured to turn off or turn off during the specified time range.

    By default, AP indicators are allowed to turn on.

  5. Run:

    quit

    Return to the WLAN view.

  6. Run:

    radio-2g-profile name profile-name or radio-5g-profile name profile-name

    A 2G or 5G radio profile is created and the radio profile view is displayed.

    By default, the system provides the 2G radio profile default and 5G radio profile default.

  7. Run:

    wifi-light { signal-strength | traffic }

    The information reflected by the blinking frequency of the Wireless indicator on an AP is configured.

    By default,
    • If the Mesh function is enabled on the AP, the blinking frequency of the Wireless LED reflects the weakest signal strength of all neighboring APs.
    • If WDS is enabled on an AP, the blinking frequency of the Wireless LED reflects the strength of signals received from a WDS AP.
      • If the AP works in leaf mode, the blinking frequency of the Wireless LED reflects the strength of signals received from a middle AP.
      • If the AP works in middle mode, the blinking frequency of the Wireless LED reflects the strength of signals received from a root AP.
      • If the AP works in root mode, the blinking frequency of the Wireless LED reflects the weakest signal strength of middle APs.
    • If the WDS and Mesh functions are disabled on an AP, the blinking frequency of the Wireless LED reflects the service traffic volume on the radio.

    On a WDS network, you need to adjust AP locations and antenna directions to obtain strong signals between WDS-capable APs. The blinking frequency of the Wireless LED shows the signal strength.

    NOTE:

    This command takes effect only when the AP has the WDS or Mesh function enabled. If the WDS and Mesh functions are disabled on the AP, the Wireless LED always shows service traffic volume.

    Only APs having Wireless LEDs support this command.

  8. Run:

    quit

    Return to the WLAN view.

  9. Bind an AP system profile and a radio profile to an AP group or AP.

    • Binding an AP system profile and a radio profile to an AP group
      1. Run the ap-group name group-name command to enter the AP group view.
      2. Run the ap-system-profile profile-name command to bind the AP system profile to the AP group.

        By default, the AP system profile default is bound to an AP group.

      3. Run the radio-2g-profile profile-name { radio { radio-id | all } } or radio-5g-profile profile-name { radio { id | all } } command to bind the radio profile to the radio.

        By default, the 2G radio profile default is bound to the 2G radio, and the 5G radio profile default is bound to the 5G radio.

    • Bind an AP system profile and a radio profile to an AP
      1. Run the ap-id ap-id, ap-mac ap-mac, or ap-name ap-name command to enter the AP view.
      2. Run the ap-system-profile profile-name command to bind the AP system profile to the AP.

        By default, no AP system profile is bound to an AP.

      3. Run the radio-2g-profile profile-name { radio { radio-id | all } } or radio-5g-profile profile-name { radio { id | all } } command to bind the radio profile to the radio.

        By default, the 2G radio profile default is bound to the 2G radio, and the 5G radio profile default is bound to the 5G radio.

  10. Run:

    quit

    Return to the WLAN view.

  11. Run:

    commit { all | ap-name ap-name | ap-id { ap-id1 [ to ap-id2 ] } &<1-10> }

    Configurations are delivered to APs.

Translation
Download
Updated: 2019-04-20

Document ID: EDOC1000142094

Views: 122177

Downloads: 120

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next