No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

MIB Reference

S12700 V200R010C00

This document provides the function overview, relationships between tables, description of single objects, description of MIB tables, and description of alarm objects.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
hwMplsTunnelTable

hwMplsTunnelTable

hwMplsTunnelTable is used to display the name of the tunnel, types of the reserved bandwidth and configuration attributes related to FRR.Including: the name of the primary tunnel, types of reserved bandwidth, session attributes, setup priority of the bypass tunnel, holding priority of the bypass tunnel, value of reserved bandwidth of the bypass tunnel, FRR switching times, table index bound to the bypass tunnel.

The indexes of the table are hwMplsTunnelInde, hwMplsTunnelInstance, hwMplsTunnelIngressLSRId, and hwMplsTunnelEgressLSRId.

OID

Object Name

Syntax

Max Access

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.121.1.1.1.1

hwMplsTunnelIndex

MplsTunnelIndex

Not-accessible

Uniquely identifies a set of tunnel instances between a pair of ingress and egress LSRs.

When the MPLS signaling protocol is rsvp(2), this value equals to the value signaled in the Tunnel ID of the SESSION object. When the MPLS signaling protocol is crldp(3), this value equals to the value signaled in the LSP ID. Reference to MPLS-TE-STD-MIB.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.2

hwMplsTunnelInstance

MplsTunnelInstanceIndex

Not-accessible

Uniquely identifies a particular instance of a tunnel between a pair of ingress and egress LSRs. It is used to identify multiple instances of tunnels for backup and parallel tunnels.

When the MPLS signaling protocol is rsvp(2), this value equals to the LSP ID of the Sender Template object. When the signaling protocol is crldp(3), there is no equivalent signaling object. Reference to MPLS-TE-STD-MIB.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.3

hwMplsTunnelIngressLSRId

MplsExtendedTunnelId

Not-accessible

Indicates the ingress LSR ID of this tunnel. When the MPLS signaling protocol is rsvp(2), this value equals to the Tunnel Sender Address in the Sender Template object and may equal to the Extended Tunnel ID in the SESSION object. When the MPLS signaling protocol is crldp(3), this value equals to the Ingress LSR Router ID in the LSPID TLV object. Reference to MPLS-TE-STD-MIB.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.4

hwMplsTunnelEgressLSRId

MplsExtendedTunnelId

Not-accessible

Indicates the egress LSR ID of this tunnel. Reference to MPLS-TE-STD-MIB.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.5

hwMplsTunnelClassType

INTEGER{bc0(1),bc1(2),invalidValue(3)}

read-only

Indicates the bandwidth type used by this tunnel. Options:

  • 1: BC0

  • 2: BC1

  • 3: invalid value

This object is obsolete. Its value can only be 3.

1.3.6.1.4.1.2011.5.25.121.1.1.1.6

hwMplsTunnelBandwidth

Integer32

read-only

Indicates the bandwidth used by this tunnel.

This object is obsolete. Its value can only be the default invalid value.

1.3.6.1.4.1.2011.5.25.121.1.1.1.7

hwMplsTunnelAdminStatus

INTEGER{up(1),down(2),testing(3)}

Read-only

Indicates the management status of this tunnel. Reference to MPLS-TE-STD-MIB.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.8

hwMplsTunnelOperStatus

INTEGER{up(1),down(2),testing(3),unknown(4),dormant(5),notPresent(6),lowerLayerDown(7)}

Read-only

Indicates the actual operating status of this tunnel, which is but not limited to the status of this tunnel of a certain period. Reference to MPLS-TE-STD-MIB.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.9

hwMplsTunnelSessionAttr

BITS{localProtectionDesired(0),nodeProtectionDesired(1),bandwidthProtectionDesired(2)}

Read-only

Indicates protection types desired by the primary tunnel, such as node protection, link protection or bandwidth protection.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.10

hwMplsTunnelFrrSetupPrio

Unsigned32

Read-only

Indicates the setup PRI of auto-bypass tunnel. The value ranges from 0 to 7. By default, the setup PRI of auto-bypass tunnel is not set.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.11

hwMplsTunnelFrrHoldingPrio

Unsigned32

Read-only

Indicates the holding PRI of auto-bypass tunnel. The value ranges from 0 to 7. By default, the setup holding PRI of auto-bypass tunnel is not set.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.12

hwMplsTunnelFrrBandwidth

Unsigned32

Read-only

Indicates the protecting bandwidth of aut-obypass tunnel. Its value is defined by the configuration on the primary tunnel.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.13

hwMplsTunnelFrrSwitchover

Counter32

Read-only

Indicates FRR switching times.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.14

hwMplsTunnelFrrBypassTableIndex

Unsigned32

Read-only

Indicates the index of the bypass tunnel table, that is, the LSP ID of the bypass tunnel. The bypass table shows interfaces protected by specified bypass tunnel.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.15

hwMplsTunnelFrrARHopTableIndex

Unsigned32

Read-only

Indicates the table index of the protection type adopted by each hop of the primary tunnel.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.16

hwMplsTunnelName

SnmpAdminString

Read-only

Indicates the tunnel name. The name can refer to the tunnel on the console port of the LSR. If mplsTunnelIsIf is set to True, the IfName of the interface corresponding to this tunnel should have a value equal to hwMplsTunnelName. Reference to the description of IfName in RFC 2863.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.17

hwMplsTunnelIfIndex

Unsigned32

Read-only

Indicates the interface index of the tunnel. It uniquely identifies the tunnel name.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.18

hwMplsTunnelPreBandwidth

Unsigned32

Read-only

The value of this object identifies the original tunnel bandwidth (in kbit/s) after a tunnel is changed.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.121.1.1.1.19

hwMplsTunnelNextBandwidth

Unsigned32

Read-only

The value of this object identifies the changed tunnel bandwidth (in kbit/s) after a tunnel is changed.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.121.1.1.1.20

hwMplsTunnelCt0Bandwidth

Unsigned32

Read-only

The bandwidth of Class-Type 0 (CT0) in this tunnel, in Kbit/sec.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.21

hwMplsTunnelCt1Bandwidth

Unsigned32

Read-only

The bandwidth of Class-Type 1 (CT1) in this tunnel, in Kbit/sec.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.22

hwMplsTunnelCt2Bandwidth

Unsigned32

Read-only

The bandwidth of Class-Type 2 (CT2) in this tunnel, in Kbit/sec.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.23

hwMplsTunnelCt3Bandwidth

Unsigned32

Read-only

The bandwidth of Class-Type 3 (CT3) in this tunnel, in Kbit/sec.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.24

hwMplsTunnelCt4Bandwidth

Unsigned32

Read-only

The bandwidth of Class-Type 4 (CT4) in this tunnel, in Kbit/sec.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.25

hwMplsTunnelCt5Bandwidth

Unsigned32

Read-only

The bandwidth of Class-Type 5 (CT5) in this tunnel, in Kbit/sec.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.26

hwMplsTunnelCt6Bandwidth

Unsigned32

Read-only

The bandwidth of Class-Type 6 (CT6) in this tunnel, in Kbit/sec.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.27

hwMplsTunnelCt7Bandwidth

Unsigned32

Read-only

The bandwidth of Class-Type 7 (CT7) in this tunnel, in Kbit/sec.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.28

hwMplsTunnelLspType

INTEGER { invalid(0), primary(1), primary-modifing(2), hot-standby(3), hot-standby-modifing(4), ordinary(5), ordinary-modifing(6), best-effort(7), best-effort-modifing(8) }

Read-only

1. This object is meaningful only at the ingress of the tunnel.

2. It indicates LSP types:

  • 0: indicates that the LSP type is invalid, the possible cause is that the LSP is not created at an ingress.

  • 1: indicates the primary LSP.

  • 2: indicates the LSP that will replace the primary LSP.

  • 3: indicates the hot-standby LSP.

  • 4: indicates the LSP that will replace the hot-standby LSP.

  • 5: indicates the ordinary LSP.

  • 6: indicates the LSP that will replace the ordinary LSP.

  • 7: indicates the Best-Effort LSP.

  • 8: indicates the LSP that will replace the Best-Effort LSP.

3. Modifying LSPs are created when users modify the make-before-break attribute of the corresponding LSP types. After being created, modifying LSPs replace the corresponding LSPs to transmit traffic.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.29

hwMplsTunnelInterfaceName

SnmpAdminString

Read-only

Indicates the tunnel interface name. The object is only valid at the ingress.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.30

hwMplsTunnelSignalProto

INTEGER { rsvpTE(1), static(2), staticCR(3) }

read-only

Indicates the signal protocol of this tunnel.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.121.1.1.1.31

hwMplsTunnelType

INTEGER { invalid(1), primaryTunnel(2), bypassTunnel(3) }

read-only

This object is meaningful only at the ingress of the tunnel. It indicates tunnel types:

  • 1: indicates that the tunnel type is invalid, the possible cause is that it is not ingress node of this tunnel.

  • 2: indicates that this is a primary tunnel.

  • 3: indicates that this is a bypass tunnel.

This object is implemented as defined in the corresponding MIB files.

Creation Restriction

None.

Modification Restriction

None.

Deletion Restriction

None.

Access Restriction

None.

Translation
Download
Updated: 2019-04-20

Document ID: EDOC1000142096

Views: 116403

Downloads: 75

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next