No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

OceanStor 9000 V300R006C10 Parts Replacement 06

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Replacing the Li&Mn Battery

Replacing the Li&Mn Battery

Impact on the System

  • Before replacing the Li&Mn battery, you must power off the storage node. This will adversely affect the services running on the node. Exercise caution when performing this operation.

Prerequisites

  • The replacement Li&Mn battery is ready.
  • You have recorded the cable mapping of the device, securely stopped the services, executed a shut-down command in the operating system to power off the storage node, and disconnected the node from power sockets and peripheral devices.

Tools and Materials

  • Flat-head screwdrivers
  • Phillips screwdrivers
  • ESD gloves
  • ESD wrist straps
  • ESD bags
  • Labels

Procedure

  1. Wear an ESD wrist strap or ESD gloves.
  2. Use the KVM to log in to the operating system of the node, enter user name root and its password (default: Root@storage), and run poweroff command to power off the node.

    Wait until the KVM has no output. The power-off is complete.

  3. Remove all power cables and external signal cables.
  4. Remove the storage node from the enclosure.
    1. Slide the storage node out of the cabinet, as shown in step 1 in Figure 2-136.
    2. Press the baffle plate and slide the storage node out of enclosure, as shown in step 2 in Figure 2-136.

    Figure 2-136  Removing a storage node

  5. Remove the enclosure cover.
    1. Use a flat-head screwdriver to loosen the latch that secures the ejector lever of the enclosure cover, as shown in step 1 in Figure 2-137.
    2. Open the ejector lever to push the enclosure cover backwards, as shown in step 2 in Figure 2-137.

      Figure 2-137  Removing an enclosure cover

  6. Remove the Li&Mn battery.
    1. Pull up the right end of the battery and remove it from the slot. See Figure 2-138.

      Figure 2-138  Removing the Li&Mn battery

  7. Place the removed Li&Mn battery in an ESD bag.
  8. Take the spare Li&Mn battery out of its ESD bag.
  9. Install the Li&Mn battery.
    1. Hold the battery with the side marked with text facing upwards, insert the left end of the battery into the slot, and gently press down the battery until it is properly installed in the slot. See Figure 2-139.

      Figure 2-139  Installing the Li&Mn battery

  10. Install the enclosure cover.
    1. Place the enclosure cover horizontally, align it with the fixing slots on both side panels of the enclosure, and close the ejector lever, as shown in steps 1 and 2 in Figure 2-140.
    2. Use a flat-head screwdriver to tighten the latch in order to secure the ejector lever of the enclosure cover, as shown in step 3 in Figure 2-140.

      Figure 2-140  Installing an enclosure cover

  11. Put the storage node into the cabinet.
    1. Align the securing holes in the inner rails with the positioning pins on the storage node, and secure the inner rails to the storage node, as shown in step 1 in Figure 2-141.
    2. Align the inner rails with the holding rails, and push the storage node into the holding rails, as shown in step 2 in Figure 2-141.
    3. Ensure that the storage node is horizontally installed and screwed.

    Figure 2-141  Installing a storage node

  12. Connect the storage node to the power sockets and peripheral devices according to the cable connection labels. Then power on the storage node.
  13. Inspect the system using SmartKit. Choose Home > Storage > Routine Maintenance > More > Inspection to check the system status. For details, see the OceanStor 9000 Routine Maintenance.

    • If all inspection items are successful: The inspection is successful.
    • If some inspection items fail the inspection: The inspection is failed. Rectify the faults by taking recommended actions in the inspection reports. You need to reperform inspection after rectifying. If the inspection is still failed, contact Huawei technical support.

Follow-up Procedure

After replacing the Li&Mn battery, label the replaced Li&Mn battery to facilitate subsequent operations.

Translation
Download
Updated: 2019-02-25

Document ID: EDOC1000162172

Views: 29067

Downloads: 28

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next