No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Command Reference

CloudEngine 8800, 7800, 6800, and 5800 V200R002C50

This document describes all the configuration commands of the device, including the command function, syntax, parameters, views, default level, usage guidelines, examples, and related commands.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
ospfv3 timer retransmit

ospfv3 timer retransmit

Function

The ospfv3 timer retransmit command specifies the interval for retransmitting the LSA on the interface instance.

The undo ospfv3 timer retransmit command restores the default value.

By default, the interval for retransmitting LSAs is 5 seconds.

Format

ospfv3 timer retransmit interval [ instance instance-id ]

undo ospfv3 timer retransmit [ interval ] [instance instance-id ]

Parameters

Parameter Description Value
interval Indicates the interval for retransmitting LSAs. The value is an integer ranging from 1 to 3600, in seconds.
instance instance-id Specifies the interface instance ID. The value is an integer ranging from 0 to 255. The default value is 0.

Views

Interface view

Default Level

2: Configuration level

Usage Guidelines

After sending an LSA to its neighbor, a switch needs to wait for the Ack packet from the neighbor. If the switch does not receive the Ack packet in the retransmission interval, the switch retransmits the LSA.

The interval for retransmitting LSA between the neighboring switches should not be set too short. Otherwise, it leads to unnecessary retransmission.

Before running this command on an interface, run the ospfv3 area command on the interface to enable OSPFv3.

Example

# Set the interval for retransmitting the LSA between VLANIF 10 and its neighboring switch to 12 seconds.

<HUAWEI> system-view
[~HUAWEI] ospfv3
[*HUAWEI-ospfv3-1] router-id 10.1.1.1
[*HUAWEI-ospfv3-1] quit
[*HUAWEI] interface vlanif 10
[*HUAWEI-Vlanif10] ipv6 enable
[*HUAWEI-Vlanif10] ospfv3 1 area 1
[*HUAWEI-Vlanif10] ospfv3 timer retransmit 12

# Set the interval for retransmitting the LSA between 10GE1/0/1 and its neighboring switch to 12 seconds.

<HUAWEI> system-view
[~HUAWEI] ospfv3
[*HUAWEI-ospfv3-1] router-id 10.1.1.1
[*HUAWEI-ospfv3-1] quit
[*HUAWEI] interface 10ge 1/0/1
[*HUAWEI-10GE1/0/1] undo portswitch
[*HUAWEI-10GE1/0/1] ipv6 enable
[*HUAWEI-10GE1/0/1] ospfv3 1 area 1
[*HUAWEI-10GE1/0/1] ospfv3 timer retransmit 12
Translation
Download
Updated: 2019-03-21

Document ID: EDOC1000166501

Views: 70474

Downloads: 376

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next