No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Command Reference

CloudEngine 8800, 7800, 6800, and 5800 V200R002C50

This document describes all the configuration commands of the device, including the command function, syntax, parameters, views, default level, usage guidelines, examples, and related commands.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Example for Multiple Users to Configure a Same Service in Two-Stage Mode

Example for Multiple Users to Configure a Same Service in Two-Stage Mode

Networking Requirements

As shown in Figure 2-3, user A and user B log in to the device at the same time. After user A configures a service on the device, user B performs the same configuration for the service on the device.

Figure 2-3  Networking diagram for multiple users to configure a same service in two-stage mode

When user B submits a configuration that is the same as the configuration submitted by user A, the system will notify user B that the configuration conflicts with an existing configuration.

Configuration Roadmap

The configuration roadmap is as follows:

  1. User A and user B configure the same service successively.

  2. User A submits the configuration.

  3. User B submits the configuration.

Procedure

  1. User A and user B configure the same service successively.

    • User A configures the IP address of VLANIF 10 to be 10.10.10.1.

      <HUAWEI> system-view
      [~HUAWEI] vlan 10
      [*HUAWEI-vlan10] quit
      [*HUAWEI] interface 10ge 1/0/1
      [*HUAWEI-10GE1/0/1] port link-type trunk
      [*HUAWEI-10GE1/0/1] port trunk allow-pass vlan 10
      [*HUAWEI-10GE1/0/1] quit
      [*HUAWEI] interface vlanif 10
      [*HUAWEI-Vlanif10] ip address 10.10.10.1 255.255.0.0
    • User B configures the IP address of VLANIF 10 to be 10.10.10.1.

      <HUAWEI> system-view
      [~HUAWEI] vlan 10
      [*HUAWEI-vlan10] quit
      [*HUAWEI] interface 10ge 1/0/1
      [*HUAWEI-10GE1/0/1] port link-type trunk
      [*HUAWEI-10GE1/0/1] port trunk allow-pass vlan 10
      [*HUAWEI-10GE1/0/1] quit
      [*HUAWEI] interface vlanif 10
      [*HUAWEI-Vlanif10] ip address 10.10.10.1 255.255.0.0

  2. User A submits the configuration.

    [*HUAWEI-Vlanif10] commit

  3. User B submits the configuration.

    [*HUAWEI-Vlanif10] commit
    ip address 10.10.10.1 255.255.0.0
    Error: The address already exists.
    Commit canceled, the configuration conflicted with other user, you can modify th
    e configuration and commit again.  

    The system prompts user B that the configuration of user B conflicts with that of user A.

Configuration Files

# 
interface Vlanif10
 ip address 10.10.10.1 255.255.0.0
#
interface 10GE1/0/1
 port link-type trunk
 port trunk allow-pass vlan 10
#
return 
Translation
Download
Updated: 2019-03-21

Document ID: EDOC1000166501

Views: 69243

Downloads: 374

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next