No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Command Reference

CloudEngine 8800, 7800, 6800, and 5800 V200R002C50

This document describes all the configuration commands of the device, including the command function, syntax, parameters, views, default level, usage guidelines, examples, and related commands.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
ospfv3 network-type

ospfv3 network-type

Function

The ospfv3 network-type command sets the network type of the OSPFv3 interface.

The undo ospfv3 network-type command restores the default network type of the OSPFv3 interface.

By default, the network type of an interface is determined by the physical interface. The network type of Ethernet interface is broadcast.

Format

ospfv3 network-type { broadcast | nbma | p2mp [ non-broadcast ] | p2p } [ instance instance-id ]

undo ospfv3 network-type [ broadcast | nbma | p2mp [ non-broadcast ] | p2p ] [ instance instance-id ]

Parameters

Parameter Description Value
broadcast Indicates that the network type of the interface is changed to broadcast. -
nbma Indicates that the network type of the interface is changed to NBMA. -
p2mp Indicates that the network type of the interface is changed to point-to-multipoint. -
non-broadcast Indicates that the network type of the interface is changed to non-broadcast point-to-multipoint. -
p2p Indicates that the network type of the interface is changed to point-to-point. -
instance instance-id Specifies the instance ID of the interface. The value is an integer ranging from 0 to 255. The default value is 0.

Views

Interface view

Default Level

2: Configuration level

Usage Guidelines

Usage Scenario

The command cannot be run on null interfaces.

The network types of two OSPFv3 interfaces on the both ends of a link must be identical. Otherwise, the two interfaces cannot set up a neighbor relationship.

Prerequisites

OSPFv3 has been enabled using the ospfv3 area command in the interface view.

Example

# Set network type of Vlanif10 to NBMA.

<HUAWEI> system-view
[~HUAWEI] ospfv3
[*HUAWEI-ospfv3-1] router-id 10.1.1.1
[*HUAWEI-ospfv3-1] quit
[*HUAWEI] interface vlanif 10
[*HUAWEI-Vlanif10] ipv6 enable
[*HUAWEI-Vlanif10] ospfv3 1 area 1
[*HUAWEI-Vlanif10] ospfv3 network-type nbma

# Set network type of 10GE1/0/1 to NBMA.

<HUAWEI> system-view
[~HUAWEI] ospfv3
[*HUAWEI-ospfv3-1] router-id 10.1.1.1
[*HUAWEI-ospfv3-1] quit
[*HUAWEI] interface 10ge 1/0/1
[*HUAWEI-10GE1/0/1] undo portswitch
[*HUAWEI-10GE1/0/1] ipv6 enable
[*HUAWEI-10GE1/0/1] ospfv3 1 area 1
[*HUAWEI-10GE1/0/1] ospfv3 network-type nbma
Translation
Download
Updated: 2019-03-21

Document ID: EDOC1000166501

Views: 43217

Downloads: 328

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next