No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Virtualization

CloudEngine 12800 and 12800E V200R002C50

This document describes the configurations of virtualization, including stack and VS.

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring a Stack Member ID

Configuring a Stack Member ID

Context

Stack member IDs are used to identify and manage member switches in a stack. Each member switch has a unique stack member ID.

If stack member IDs conflict in a stack, the master switch assigns new stack member IDs to member switches. That is, the master switch checks stack member IDs in ascending order (from 1 to the largest stack member ID) to find an unused stack member ID and then assigns the found stack member ID to the member switch with a conflicting stack member ID.

Procedure

  1. Run the system-view command to enter the system view.
  2. Run the stack command to enter the stack management view.
  3. Run the stack member new-member-id command to configure a stack member ID for the local switch.

    By default, the stack member ID of a switch is 1. After changing the stack member ID, restart the switch for the configuration to take effect.

    When a switch already has the stacking function enabled, run the stack member member-id renumber new-member-id [ inherit-config ] command to change the stack member ID of the switch.

    If you specify inherit-config, the switch inherits the original stack configuration after it restarts, including the stack priority, stack domain ID, connection mode, and physical member port configuration.

    If you do not specify inherit-config, the current stack configuration is lost after the switch restarts, and the configuration related to the new stack member ID in the configuration file takes effect.

    For example, if a switch uses a stack member ID 1 and has the following stack priority configuration:
    #
    stack member 1 priority 150
    #
    If inherit-config is specified when the stack member ID is changed to 2, member ID 2 will inherit the stack priority configuration of member ID 1 after the switch restarts. For example:
    #
    stack member 1 priority 150      // Configuration of member ID 1 becomes the offline configuration.
    #
    stack member 2 priority 150      // Member ID 2 inherits the stack priority configuration of member ID 1.
    #
    If inherit-config is not specified, member ID 2 will not inherit the stack priority configuration of member ID 1 after the switch restarts. For example:
    #
    stack member 1 priority 150      // Configuration of member ID 1 becomes the offline configuration, and configuration of member ID 2 is empty.
    #
    If the switch already has offline configuration of member ID 2 before restarting, for example:
    #
    stack member 1 priority 150
    #
    stack member 2 priority 200      // The switch already has offline configuration of member ID 2 before restarting
    #
    When the stack member ID is changed to 2, inherit-config cannot be specified. The switch will use the configuration of member ID 2 in the configuration file after restarting. For example,
    #
    stack member 1 priority 150      // Configuration of member ID 1 becomes the offline configuration
    #
    stack member 2 priority 200      // Configuration of member ID 2 in the configuration file takes effect.
    #
    NOTE:
    • If the configuration file contains offline configuration for the new stack member ID, do not specify inherit-config in the command.

    • Common service port configurations, for example, port split configuration, will be lost after the stacking function has been enabled, the stack member ID is changed, and the switch restarts.

  4. Run the commit command to commit the configuration.
Translation
Download
Updated: 2019-03-21

Document ID: EDOC1000166610

Views: 43863

Downloads: 131

Average rating:
This Document Applies to these Products

Related Version

Related Documents

Share
Previous Next