No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

CloudEngine 8800, 7800, 6800, and 5800 V200R002C50 Configuration Guide - Virtualization

This document describes the configurations of virtualization, including stack and SVF.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Example for Configuring Inter-Device Eth-Trunks

Example for Configuring Inter-Device Eth-Trunks

Networking Requirements

As shown in Figure 1-37, SwitchA and SwitchB set up a stack. The stack connects to the upstream and downstream devices (SwitchC, SwitchD, and SwitchE) through inter-device Eth-Trunks.
Figure 1-37 Inter-device Eth-Trunk networking

Configuration Roadmap

The configuration roadmap is as follows:
  1. Add the links that connect the stack to the upstream and downstream devices to inter-device Eth-Trunks. This configuration improves link bandwidth and reliability, while eliminating loops on the network.

Procedure

  1. Configure inter-device Eth-Trunks.

    # On the stack, create Eth-Trunk10, Eth-Trunk20, and Eth-Trunk30, and add the interfaces connected to the upstream and downstream devices to the Eth-Trunks.

    <HUAWEI> system-view
    [~HUAWEI] interface eth-trunk 10
    [*HUAWEI-Eth-Trunk10] trunkport 10ge 1/0/5
    [*HUAWEI-Eth-Trunk10] trunkport 10ge 2/0/5
    [*HUAWEI-Eth-Trunk10] quit
    [*HUAWEI] interface eth-trunk 20
    [*HUAWEI-Eth-Trunk20] trunkport 10ge 1/0/6
    [*HUAWEI-Eth-Trunk20] trunkport 10ge 2/0/6
    [*HUAWEI-Eth-Trunk20] quit
    [*HUAWEI] interface eth-trunk 30
    [*HUAWEI-Eth-Trunk30] trunkport 10ge 1/0/7
    [*HUAWEI-Eth-Trunk30] trunkport 10ge 2/0/7
    [*HUAWEI-Eth-Trunk30] commit
    [~HUAWEI-Eth-Trunk30] return
    

    # On SwitchC, create Eth-Trunk10 and add interfaces connected to the stack to Eth-Trunk10. The configurations on SwitchD and SwitchE are similar to the configuration on SwitchC, and are not mentioned here.

    <HUAWEI> system-view
    [~HUAWEI] sysname SwitchC
    [*HUAWEI] commit
    [~SwitchC] interface eth-trunk 10
    [*SwitchC-Eth-Trunk10] trunkport 10ge 1/0/1
    [*SwitchC-Eth-Trunk10] trunkport 10ge 1/0/2
    [*SwitchC-Eth-Trunk10] commit
    [~SwitchC-Eth-Trunk10] return
    

  2. Verify the configuration.

    After the configuration is complete, run the display eth-trunk membership trunk-id command in any view to view information about member interfaces of the Eth-Trunks. Information about member interfaces of Eth-Trunk10 on the stack is used as an example.

    <HUAWEI> display eth-trunk membership 10
    Trunk ID: 10
    Used Status: Valid
    Type: Ethernet
    Working Mode: Normal
    Number Of Ports in Trunk: 2
    Number Of Up Ports in Trunk: 2
    Operating Status: up
    
    Interface 10GE1/0/5, valid, operate up, weight=1
    Interface 10GE2/0/5, valid, operate up, weight=1
    

Configuration Files

  • Stack configuration file

    #
    interface Eth-Trunk10
    #  
    interface Eth-Trunk20
    #  
    interface Eth-Trunk30
    #  
    interface 10GE1/0/5 
     eth-trunk 10
    # 
    interface 10GE1/0/6 
     eth-trunk 20
    # 
    interface 10GE1/0/7 
     eth-trunk 30
    # 
    interface 10GE2/0/5 
     eth-trunk 10
    #
    interface 10GE2/0/6 
     eth-trunk 20
    #
    interface 10GE2/0/7 
     eth-trunk 30
    # 
    return
    
  • SwitchC configuration file

    #
    sysname SwitchC
    # 
    interface Eth-Trunk10
    #  
    interface 10GE1/0/1 
     eth-trunk 10
    # 
    interface 10GE1/0/2 
     eth-trunk 10
    #
    return
    
  • SwitchD configuration file

    #
    sysname SwitchD
    # 
    interface Eth-Trunk20
    #  
    interface 10GE1/0/1 
     eth-trunk 20
    # 
    interface 10GE1/0/2 
     eth-trunk 20
    #
    return
    
  • SwitchE configuration file

    #
    sysname SwitchE
    # 
    interface Eth-Trunk30
    #  
    interface 10GE1/0/1 
     eth-trunk 30
    # 
    interface 10GE1/0/2 
     eth-trunk 30
    #
    return
    
Translation
Download
Updated: 2019-04-20

Document ID: EDOC1000166645

Views: 38926

Downloads: 300

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next