Configuring QinQ

MZ520 NIC V100R001 User Guide 09

This document describes the MZ520 in terms of its functions, appearance, features, configuration methods, and application examples.

Rate and give feedback:

Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).

Configuring QinQ

Family Firmware supports the QinQ function from version 7.14.15.

Configuring QinQ in SF Mode

When the following screen is displayed, press F11 to enter the Front Page screen.
Figure 4-161 Pressing F11 to go to Front Page
On the Front Page screen, select Device Manager and press Enter.
Figure 4-162 Selecting Device Manager
On the Device Manager screen, select Network Device List and press Enter.
Figure 4-163 Selecting Network Device List
Select a port and press Enter. On the displayed screen, press Enter again to confirm the selection.
Figure 4-164 Selecting a port

Figure 4-165 Confirming the selection
On the Main Configuration Page screen, select Multi-Function Mode, press Enter, and select SF to enable SF.
Figure 4-166 Selecting Multi-Function Mode

Figure 4-167 Enabling SF
Select Device Hardware Configuration Menu and press Enter.
Figure 4-168 Selecting Device Hardware Configuration Menu
Select QINQ Configuration and press Enter.
Figure 4-169 Selecting QINQ Configuration
On the QINQ Configuration screen, select QINQ VLAN Mode, press Enter, and select QINQ to enable QINQ.
Figure 4-170 Selecting QINQ VLAN Mode

Figure 4-171 Enabling QINQ
Select VLAN ID(1…4094) and press Enter, and set VLAN ID(1…4094). For example, to set the VLAN ID to 100, enter 100 and press Enter.

The value range of VLAN ID is 1 to 4094.

Figure 4-172 Selecting VLAN ID(1…4094)

Figure 4-173 Setting VLAN ID
Press Esc repeatedly until the Front Page screen is displayed.
Restart the compute node for the configuration to take effect.

Configuring QinQ in NPAR Mode

When the following screen is displayed, press F11 to enter the Front Page screen.
Figure 4-174 Pressing F11 to go to Front Page
On the Front Page screen, select Device Manager and press Enter.
Figure 4-175 Selecting Device Manager
On the Device Manager screen, select Network Device List and press Enter.
Figure 4-176 Selecting Network Device List
Select a port and press Enter. On the displayed screen, press Enter again to confirm the selection.
Figure 4-177 Selecting a port

Figure 4-178 Confirming the selection
On the Main Configuration Page screen, select Multi-Function Mode, press Enter, and select NPAR to enable NPAR.
Figure 4-179 Selecting Multi-Function Mode

Figure 4-180 Enabling NPAR
Select NIC Partitioning Configuration Menu and press Enter.
Figure 4-181 Selecting NIC Partitioning Configuration Menu
Select QINQ Configuration and press Enter.
Figure 4-182 Selecting QINQ Configuration
On the QINQ Configuration screen, select QINQ VLAN Mode, press Enter, and select QINQ to enable QINQ.
Figure 4-183 Selecting QINQ VLAN Mode

Figure 4-184 Enabling QINQ
Select 1st Partition VLAN ID(1…4094) and press Enter, and set the VLAN ID. For example, to set the VLAN ID to 100, enter 100 and press Enter.

The value range of 1st Partition VLAN ID is 1 to 4094.

Figure 4-185 Selecting 1st Partition VLAN ID(1…4094)

Figure 4-186 Setting 1st Partition VLAN ID
Repeat 9 to set 2nd Partition VLAN ID(1…4094), 3rd Partition VLAN ID(1…4094), and 4th Partition VLAN ID(1…4094).

The values of 1st Partition VLAN ID, 2nd Partition VLAN ID(1…4094), 3rd Partition VLAN ID(1…4094), and 4th Partition VLAN ID(1…4094) must be different. If any two VLAN IDs are the same, the QinQ configuration cannot be saved successfully.
Press Esc repeatedly until the Front Page screen is displayed.
Restart the compute node for the configuration to take effect.