Configuring QinQ

MZ522 NIC V100R001 User Guide 07

This document describes the MZ522 in terms of its functions, appearance, features, configuration methods, and application examples.

Rate and give feedback:

Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).

Configuring QinQ

Family Firmware supports the QinQ function from version 7.14.15.

Configuring QinQ in SF Mode

When the following screen is displayed, press F11 to enter the Front Page screen.
Figure 4-150 Pressing F11 to go to Front Page
On the Front Page screen, select Device Manager and press Enter.
Figure 4-151 Selecting Device Manager
On the Device Manager screen, select Network Device List and press Enter.
Figure 4-152 Selecting Network Device List
Select a port and press Enter. On the displayed screen, press Enter again to confirm the selection.
Figure 4-153 Selecting a port

Figure 4-154 Confirming the selection
On the Main Configuration Page screen, select Multi-Function Mode, press Enter, and select SF to enable SF.
Figure 4-155 Selecting Multi-Function Mode

Figure 4-156 Enabling SF
Select Device Hardware Configuration Menu and press Enter.
Figure 4-157 Selecting Device Hardware Configuration Menu
Select QINQ Configuration and press Enter.
Figure 4-158 Selecting QINQ Configuration
On the QINQ Configuration screen, select QINQ VLAN Mode, press Enter, and select QINQ to enable QINQ.
Figure 4-159 Selecting QINQ VLAN Mode

Figure 4-160 Enabling QINQ
Select VLAN ID(1…4094) and press Enter, and set VLAN ID(1…4094). For example, to set the VLAN ID to 100, enter 100 and press Enter.

The value range of VLAN ID is 1 to 4094.

Figure 4-161 Selecting VLAN ID(1…4094)

Figure 4-162 Setting VLAN ID
Press Esc repeatedly until the Front Page screen is displayed.
Restart the compute node for the configuration to take effect.

Configuring QinQ in NPAR Mode

When the following screen is displayed, press F11 to enter the Front Page screen.
Figure 4-163 Pressing F11 to go to Front Page
On the Front Page screen, select Device Manager and press Enter.
Figure 4-164 Selecting Device Manager
On the Device Manager screen, select Network Device List and press Enter.
Figure 4-165 Selecting Network Device List
Select a port and press Enter. On the displayed screen, press Enter again to confirm the selection.
Figure 4-166 Selecting a port

Figure 4-167 Confirming the selection
On the Main Configuration Page screen, select Multi-Function Mode, press Enter, and select NPAR to enable NPAR.
Figure 4-168 Selecting Multi-Function Mode

Figure 4-169 Enabling NPAR
Select NIC Partitioning Configuration Menu and press Enter.
Figure 4-170 Selecting NIC Partitioning Configuration Menu
Select QINQ Configuration and press Enter.
Figure 4-171 Selecting QINQ Configuration
On the QINQ Configuration screen, select QINQ VLAN Mode, press Enter, and select QINQ to enable QINQ.
Figure 4-172 Selecting QINQ VLAN Mode

Figure 4-173 Enabling QINQ
Select 1st Partition VLAN ID(1…4094) and press Enter, and set the VLAN ID. For example, to set the VLAN ID to 100, enter 100 and press Enter.

The value range of 1st Partition VLAN ID is 1 to 4094.

Figure 4-174 Selecting 1st Partition VLAN ID(1…4094)

Figure 4-175 Setting 1st Partition VLAN ID
Repeat 9 to set 2nd Partition VLAN ID(1…4094), 3rd Partition VLAN ID(1…4094), and 4th Partition VLAN ID(1…4094).

The values of 1st Partition VLAN ID, 2nd Partition VLAN ID(1…4094), 3rd Partition VLAN ID(1…4094), and 4th Partition VLAN ID(1…4094) must be different. If any two VLAN IDs are the same, the QinQ configuration cannot be saved successfully.
Press Esc repeatedly until the Front Page screen is displayed.
Restart the compute node for the configuration to take effect.