Configuring VLAN filter
Family Firmware supports the VLAN filter function from version 7.14.15.
Configuring VLAN Filter in SF Mode
- When the following screen is displayed, press F11 to enter the Front Page screen.Figure 4-120 Pressing F11 to go to Front Page
- On the Front Page screen, select Device Manager and press Enter.Figure 4-121 Selecting Device Manager
- On the Device Manager screen, select Network Device List and press Enter.Figure 4-122 Selecting Network Device List
- Select a port and press Enter. On the displayed screen, press Enter again to confirm the selection.Figure 4-123 Selecting a portFigure 4-124 Confirming the selection
- On the Main Configuration Page screen, select Multi-Function Mode, press Enter, and select SF to enable SF.Figure 4-125 Selecting Multi-Function ModeFigure 4-126 Enabling SF
- Select Device Hardware Configuration Menu and press Enter.Figure 4-127 Selecting Device Hardware Configuration Menu
- Select QINQ Configuration and press Enter.Figure 4-128 Selecting QINQ Configuration
- On the QINQ Configuration screen, select QINQ VLAN Mode, press Enter, and select FILTERING to enable FILTERING.Figure 4-129 Selecting QINQ VLAN ModeFigure 4-130 Enabling FILTERING
- Select VLAN ID(1…4094) and press Enter, and set the VLAN ID. For example, to set the VLAN ID to 100, enter 100 and press Enter.
The value range of VLAN ID is 1 to 4094.
Figure 4-131 Selecting VLAN ID(1…4094)Figure 4-132 Setting VLAN ID - Select VLAN id pool and press Enter, and set VLAN id pool. For example, to set VLAN id pool to 100 to 200 and 500, enter 100-200 500 and press Enter.
- The total number of VLAN IDs for each chip cannot exceed 256.
- You can enter a number or a number segment for VLAN id pool, for example, 100-200 500.
- If VLAN id pool is not specified, the port does not receive packets.
Figure 4-133 Selecting VLAN id poolFigure 4-134 Setting VLAN id pool - Press Esc repeatedly until the Front Page screen is displayed.
- Restart the compute node for the configuration to take effect.
Setting VLAN Filter in NPAR Mode
- When the following screen is displayed, press F11 to enter the Front Page screen.Figure 4-135 Pressing F11 to go to Front Page
- On the Front Page screen, select Device Manager and press Enter.Figure 4-136 Selecting Device Manager
- On the Device Manager screen, select Network Device List and press Enter.Figure 4-137 Selecting Network Device List
- Select a port and press Enter. On the displayed screen, press Enter again to confirm the selection.Figure 4-138 Selecting a portFigure 4-139 Confirming the selection
- On the Main Configuration Page screen, select Multi-Function Mode, press Enter, and select NPAR to enable NPAR.Figure 4-140 Selecting Multi-Function ModeFigure 4-141 Enabling NPAR
- Select NIC Partitioning Configuration Menu and press Enter.Figure 4-142 Selecting NIC Partitioning Configuration Menu
- Select QINQ Configuration and press Enter.Figure 4-143 Selecting QINQ Configuration
- On the QINQ Configuration screen, select QINQ VLAN Mode, press Enter, and select FILTERING to enable FILTERING.Figure 4-144 Selecting QINQ VLAN ModeFigure 4-145 Enabling FILTERING
- Select 1st Partition VLAN ID(1…4094) and press Enter, and set the VLAN ID. For example, to set the VLAN ID to 100, enter 100 and press Enter.
The value range of 1st Partition VLAN ID is 1 to 4094.
Figure 4-146 Selecting 1st Partition VLAN ID(1…4094)Figure 4-147 Setting 1st Partition VLAN ID - Select VLAN id pool and press Enter, and set VLAN id pool. For example, to set VLAN id pool to 100 to 300 and 500, enter 100-300 500 and press Enter.
- The total number of VLAN IDs for each chip cannot exceed 256.
- You can enter a number or a number segment for VLAN id pool, for example, 100-300 500.
- If VLAN id pool is not specified, the port does not receive packets.
Figure 4-148 Selecting VLAN id poolFigure 4-149 Setting VLAN id pool - Repeat 9 and 10 to set 2nd Partition VLAN ID(1…4094), 3rd Partition VLAN ID(1…4094), 4th Partition VLAN ID(1…4094) and the related VLAN id pool.
- Press Esc repeatedly until the Front Page screen is displayed.
- Restart the compute node for the configuration to take effect.