No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search


To have a better experience, please upgrade your IE browser.


CLI-based Configuration Guide - Network Management and Monitoring

AR100, AR120, AR150, AR160, AR200, AR1200, AR2200, AR3200, and AR3600 V200R009

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Example for Configuring an ICMP Jitter Test

Example for Configuring an ICMP Jitter Test

Networking Requirements

In Figure 7-23, RouterA is the NQA client. Test the jitter on the network between RouterA and RouterB.

Figure 7-23  Networking diagram for configuring the ICMP Jitter test

Configuration Roadmap

Configure RouterA as the NQA client and create an ICMP Jitter test instance on RouterA.


  1. Configure IP addresses for interfaces on RouterA.

    <Huawei> system-view
    [Huawei] sysname RouterA
    [RouterA] interface gigabitethernet 1/0/0
    [RouterA-GigabitEthernet1/0/0] ip address 24
    [RouterA-GigabitEthernet1/0/0] quit

  2. Configure IP addresses for interfaces on RouterB.

    <Huawei> system-view
    [Huawei] sysname RouterB
    [RouterB] interface gigabitethernet 1/0/0
    [RouterB-GigabitEthernet1/0/0] ip address 24
    [RouterB-GigabitEthernet1/0/0] quit

  3. Enable the NQA client and create an ICMP jitter test instance.

    [RouterA] nqa test-instance admin icmpjitter
    [RouterA-nqa-admin-icmpjitter] test-type icmpjitter
    [RouterA-nqa-admin-icmpjitter] destination-address ipv4

  4. Start the ICMP jitter test.

    [RouterA-nqa-admin-icmpjitter] start now
    [RouterA-nqa-admin-icmpjitter] quit

  5. Verify the test result.

    [RouterA-nqa-admin-icmpjitter] display nqa results test-instance admin icmpjitter
     NQA entry(admin, icmpjitter) :testflag is inactive ,testtype is icmpjitter     
      1 . Test 1 result   The test is finished                                      
       SendProbe:60                         ResponseProbe:60                        
       Completion:success                   RTD OverThresholds number:0             
       OWD OverThresholds SD number:0       OWD OverThresholds DS number:0          
       Min/Max/Avg/Sum RTT:2/31/3/204       RTT Square Sum:1704                     
       NumOfRTT:60                          Drop operation number:0                 
       Operation sequence errors number:0   RTT Stats errors number:0               
       System busy operation number:0       Operation timeout number:0              
       Min Positive SD:1                    Min Positive DS:1                       
       Max Positive SD:28                   Max Positive DS:5                       
       Positive SD Number:16                Positive DS Number:16                   
       Positive SD Sum:50                   Positive DS Sum:22                      
       Positive SD Square Sum:828           Positive DS Square Sum:46               
       Min Negative SD:1                    Min Negative DS:1                       
       Max Negative SD:20                   Max Negative DS:6                       
       Negative SD Number:15                Negative DS Number:17                   
       Negative SD Sum:50                   Negative DS Sum:25                      
       Negative SD Square Sum:520           Negative DS Square Sum:63               
       Min Delay SD:1                       Min Delay DS:0                          
       Avg Delay SD:1                       Avg Delay DS:0                          
       Max Delay SD:15                      Max Delay DS:15                         
       Delay SD Square Sum:372              Delay DS Square Sum:326                 
       Packet Loss SD:0                     Packet Loss DS:0                        
       Packet Loss Unknown:0                Average of Jitter:2                     
       Average of Jitter SD:3               Average of Jitter DS:1                  
       Jitter out value:1.2249218           Jitter in value:0.6640373               
       NumberOfOWD:60                       Packet Loss Ratio: 0%                   
       OWD SD Sum:92                        OWD DS Sum:52                           
       ICPIF value: 0                       MOS-CQ value: 0                         
       TimeStamp unit: ms                   Packet Rewrite Number: 0                
       Packet Rewrite Ratio: 0%             Packet Disorder Number: 0               
       Packet Disorder Ratio: 0%            Fragment-disorder Number: 0             
       Fragment-disorder Ratio: 0%          Jitter OverThresholds SD number:0       
       Jitter OverThresholds DS number:0    OverallOverThresholds number:0          
       Start time: 2016-05-10 15:55:44                                              
       End time: 2016-05-10 15:55:45 

Configuration Files

  • RouterA configuration file

     sysname RouterA
    interface GigabitEthernet1/0/0
     ip address
    nqa test-instance admin icmpjitter
     test-type icmpjitter
     destination-address ipv4
  • RouterB configuration file

     sysname RouterB
    interface GigabitEthernet1/0/0
     ip address
Updated: 2019-05-17

Document ID: EDOC1000174072

Views: 121579

Downloads: 372

Average rating:
This Document Applies to these Products

Related Version

Related Documents

Previous Next