No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Alarm Handling

AR100-S, AR110-S, AR120-S, AR150-S, AR160-S, AR200-S, AR1200-S, AR2200-S, and AR3200-S V200R009

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
MGMD_1.3.6.1.4.1.2011.5.25.149.3.3.8 hwMgmdGMPTotalLimit

MGMD_1.3.6.1.4.1.2011.5.25.149.3.3.8 hwMgmdGMPTotalLimit

Description

MGMD/3/GLBLIMIT:OID [oid] Membership report message is discarded because the total IGMP or MLD group membership limitation is exceeded in all instances. (GroupAddressType=[integer], SrcAddr=[binary], GrpAddr=[binary], LimitCnt=[integer])

New members failed to join the IGMP or MLD group because the total number of IGMP or MLD entries in all instances reached the limit.

Attribute

Alarm ID Alarm Severity Alarm Type

1.3.6.1.4.1.2011.5.25.149.3.3.8

Minor

qualityOfServiceAlarm(3)

Parameters

Name Meaning

oid

Indicates the MIB object ID of the alarm.

GroupAddressType

Indicates the inetAddressType of group address. The value can be:
  • 1: IPv4 address

  • 2: IPv6 address

SrcAddr

Indicates the source address of the Report message.

GrpAddr

Indicates the group address of the Report message.

LimitCnt

Indicates the limit of IGMP or MLD entries in all instances.

Impact on the System

After the total number of entries in all instances reaches the limit, new members fail to join the IGMP or MLD group, and corresponding entries cannot be established. In this case, terminal users cannot receive the desired on-demand video programs.

Possible Causes

After the limit to the total number of IGMP or MLD entries in all instances was set on the router, when the total number of IGMP or MLD entries reached the limit, new members failed to join the IGMP or MLD group and the corresponding trap was generated.

Global IGMP or MLD entries include the (*,G) entries, (S,G) entries, and entries in the SSM-mapping table in all instances.

Procedure

  1. Run the display igmp all-instance group verbose and display current-configuration commands , or the display mld group verbose and display current-configuration commands to check whether the statistical number of IGMP or MLD entries in all instances is equal to or greater than the limit value that is set by the igmp global limit command or the mld global limit command.

    • If so, go to Step 2.

    • If not, go to Step 4.

  2. Check the network status and judge whether more IGMP or MLD entries can be maintained on the router of the network.

    • If so, go to Step 3.

    • If not, go to Step 5. This situation indicates that multicast services in the network are saturated and therefore no more IGMP or MLD entries can be added. It is recommended to reduce multicast services or deploy a higher-performance device as an alternative to the current device.

  3. Run the igmp global limit number command or the mld global limit command in the system view to increase the limit value of the IGMP or MLD entries in all instances. Then, check whether the trap persists.

    • If so, go to Step 1.

    • If not, go to Step 5.

  4. Collect alarm information and configuration information, and then contact technical support personnel.
  5. End.

Related Information

None

Translation
Download
Updated: 2019-05-06

Document ID: EDOC1000174085

Views: 132305

Downloads: 20

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next