No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Alarm Handling

AR100-S, AR110-S, AR120-S, AR150-S, AR160-S, AR200-S, AR1200-S, AR2200-S, and AR3200-S V200R009

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
ISIS_1.3.6.1.4.1.2011.5.25.24.2.4.17 hwIsisPeerFlapSuppStatusChange

ISIS_1.3.6.1.4.1.2011.5.25.24.2.4.17 hwIsisPeerFlapSuppStatusChange

Description

ISIS/2/NBR_SUPP_STATE_CHG:OID [oid] The status of peer flapping suppress is changed.(sysInstance=[integer], sysInstanceofInterface=[integer], circuitIndexofInterface=[integer], ifIndex=[integer], isisCircIfIndex=[integer], ifName=[string], SuppressStatus=[integer], Reason=[integer])

The status of IS-IS neighbor relationship flapping suppression changed.

Attribute

Alarm ID Alarm Severity Alarm Type
1.3.6.1.4.1.2011.5.25.24.2.4.17 Major communicationsAlarm(2)

Parameters

Name Meaning

OID

Indicates the MIB object ID of the alarm.

sysInstance

Indicates the IS-IS instance ID.

sysInstanceofInterface

Indicates the IS-IS interface index.

circuitIndexofInterface

Indicates the interface name.

ifIndex

Indicates the process ID.

isisCircIfIndex

Indicates the area ID.

ifName

Indicates the interface name.

SuppressStatus

Indicates the suppression status:

  • 0: IS-IS neighbor relationship flapping suppression is not started yet.
  • 1: IS-IS neighbor relationship flapping suppression works in Hold-down mode.
  • 2: IS-IS neighbor relationship flapping suppression works in Hold-max-cost mode.

reason

Suppression causes are as follows:
  • 1: The suppression exits because the hold-max-cost timer expires.

  • 2: The suppression exits because the hold-down timer expires.

  • 3: A configuration change occurs.

  • 4: A manual operation is performed to exit from flapping suppression.

  • 5: The neighbor relationship frequently flaps.

  • 6: Suppression is aborted forcibly using the reset isis process-id suppress-flapping peer [ interface interface-type interface-number ] [ notify-peer ] command on the remote device.

Impact on the System

Services may be interrupted if IS-IS neighbor relationship flapping suppression persists on the interface.

Possible Causes

IS-IS neighbor relationship flapping suppression started, or the interface exited from the suppression.

Procedure

  1. Run the display isis last-peer-change [ process-id | vpn-instance vpn-instance-name ] command to check whether frequent interface flapping occurs.

    • If frequent interface flapping occurs, this trap message is informational only and no action is required.
    • If no frequent interface flapping occurs, go to Step 2.

  2. Run the reset isis process-id suppress-flapping peer [ interface interface-type interface-number ] [ notify-peer ] command to force the interface to exit from IS-IS neighbor relationship flapping suppression.
  3. End.
Translation
Download
Updated: 2019-05-06

Document ID: EDOC1000174085

Views: 118387

Downloads: 19

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next