No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

MIB Reference

AR100-S, AR110-S, AR120-S, AR150-S, AR160-S, AR200-S, AR1200-S, AR2200-S, and AR3200-S V200R009

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
nqaAdminParaTable

nqaAdminParaTable

nqaAdminParaTable is used to configure parameters of a test instance.

The indexes of this table are nqaAdminCtrlOwnerIndex and nqaAdminCtrlTestName.

OID

Object Name

Syntax

Max Access

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.111.2.2.1.1

nqaAdminParaTargetAddressType

InetAddressType

Read-write

This object indicates the destination address type.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.111.2.2.1.2

nqaAdminParaTargetAddress

InetAddress

Read-write

This object indicates the destination address.

Currently, the value ranges from 0 to 100 can be set.

1.3.6.1.4.1.2011.5.25.111.2.2.1.3

nqaAdminParaTargetPort

InetPortNumber

Read-write

This object indicates the destination port number.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.111.2.2.1.4

nqaAdminParaSourceAddressType

InetAddressType

Read-write

This object indicates the source address type.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.111.2.2.1.5

nqaAdminParaSourceAddress

InetAddress

Read-write

This object indicates the source address.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.111.2.2.1.6

nqaAdminParaSourcePort

InetPortNumber

Read-write

This object indicates the source port number.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.111.2.2.1.7

nqaAdminParaMaxTtl

Unsigned32{(0..255)}

Read-write

This object indicates the maximum TTL value.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.111.2.2.1.8

nqaAdminParaInitialTtl

Unsigned32{(1..255)}

Read-write

This object indicates the initial TTL value.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.111.2.2.1.12

nqaAdminParaDataSize

Unsigned32

Read-write

The value of this object identifies the size of data field in packet.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.111.2.2.1.13

nqaAdminParaDataFill

OCTET STRING

Read-write

This object indicates the characters used for filling the data field.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.111.2.2.1.14

nqaAdminParaIfIndex

InterfaceIndexOrZero

Read-write

This object indicates the interface index. The value zero implies that the object is disabled.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.111.2.2.1.15

nqaAdminParaByPassRouteTable

TruthValue

Read-write

This object indicates whether bypassing the routing table is enabled.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.111.2.2.1.17

nqaAdminParaProbeCount

Unsigned32{(1..15)}

Read-write

This object indicates the number of packets sent by the test instance or number of repeated probes. The number of repeated probes applies only to jitter test instances.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.111.2.2.1.18

nqaAdminParaTrapGeneration

BITS

{

  • probeFailure(0)
  • testFailure(1)
  • testCompletion(2)
  • overRtdThreshold(3)
  • overOwdThresholdSd(4)
  • overOwdThresholdDs(5)

}

Read-write

This object indicates whether the trap function is enabled for the test instance. Multiple options for this object can be delivered together. If configurations are repeatedly delivered, newly delivered configurations overwrite previous configurations.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.111.2.2.1.19

nqaAdminParaTrapProbeFailureFilter

Unsigned32{(1..15)}

Read-write

This object indicates the number of packets during consecutive test instance failures.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.111.2.2.1.20

nqaAdminParaTrapTestFailureFilter

Unsigned32{(1..15)}

Read-write

This object indicates the number of consecutive test instance failures.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.111.2.2.1.21

nqaAdminParaDSField

Integer32{(0..255)}

Read-write

The value of this object identifies the Differentiated Services (DS) field.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.111.2.2.1.24

nqaAdminParaOperation

NQAOperation

Read-write

This object indicates the operation of FTP or HTTP type test instance.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.111.2.2.1.25

nqaAdminParaHttpVersion

DisplayString

Read-write

This object indicates the HTTP version.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.111.2.2.1.26

nqaAdminParaHttpOperationString

DisplayString

Read-write

This object indicates the relative path name (used by HTTP).

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.111.2.2.1.27

nqaAdminParaTestFailurePercent

Unsigned32{(0..100)}

Read-write

This object indicates the percentage of the number of failed test instances to the total number of test instances.

Currently, the value ranges from 0 to 100 can be set. The default value is 100.

1.3.6.1.4.1.2011.5.25.111.2.2.1.28

nqaAdminParaFtpUserName

DisplayString

Read-write

This object indicates the user name of an FTP server.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.111.2.2.1.29

nqaAdminParaFtpPassword

DisplayString

Read-write

This object indicates the password of the user of the FTP server.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.111.2.2.1.30

nqaAdminParaFtpFilePath

DisplayString

Read-write

This object indicates the file name and file path used by FTP.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.111.2.2.1.31

nqaAdminParaFtpFileSize

Integer32{(0..10000)}

Read-write

The value of this object identifies the size that the file will be transmitted by an FTP test instance.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.111.2.2.1.32

nqaAdminParaInterval

Integer32{(0..60000)}

Read-write

The value of this object identifies the interval between two consecutive probe packets.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.111.2.2.1.33

nqaAdminParaNumPackets

Integer32

Read-write

The value of this object identifies the number of packets sent in each probe, only apples to jitter test instances.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.111.2.2.1.34

nqaAdminParaVrfName

DisplayString

Read-write

This object indicates the VRF name.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.111.2.2.1.35

nqaAdminParaLspAddressType

INTEGER

{

  • ipv4(1)
  • te(3)

}

Read-write

The value of this object identifies the LSP address type. The object applies to LSP ping and trace test instances.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.111.2.2.1.36

nqaAdminParaLspAddressMask

Integer32

Read-write

The value of this object identifies the address mask of LSP. The object apples to LSP ping and trace test instances.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.111.2.2.1.37

nqaAdminParaLspIpAddress

InetAddress

Read-write

This object indicates the IP address filled in the IP header, which must be a 127/8 address.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.111.2.2.1.43

nqaAdminParaLspExp

Unsigned32{(0..7)}

Read-write

This object indicates the 3-bit EXP field in an MPLS echo packet label.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.111.2.2.1.44

nqaAdminParaLspReplyMode

INTEGER

{

  • noReply(1)
  • udp(2)
  • udpRouterAlert(3)
  • levelControlChannel(4)
  • udpviaVPLS(5)

}

Read-write

The value of this object identifies the ReplyMode field in an MPLS echo packet.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.111.2.2.1.45

nqaAdminParaResultRowMax

Integer32

Read-write

The value of this object identifies the maximum number of test instance result records.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.111.2.2.1.46

nqaAdminParaHistoryRowMax

Integer32

Read-write

The value of this object identifies the maximum number of history records on each test instance.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.111.2.2.1.65

nqaAdminParaIcmpJitterMode

INTEGER

{

  • icmpTimestamp(1)
  • icmpEcho(2)

}

Read-write

The value of this object identifies the type of ICMP packets to be sent in ICMP jitter tests.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.111.2.2.1.78

nqaAdminParaLspTunnelType

INTEGER

{

  • main(0)
  • hotstandby(1)

}

Read-write

Specifies the type of a TE tunnel.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.111.2.2.1.79

nqaAdminParaLspNextHopAddress

InetAddress

Read-write

This object indicates the next-hop address.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.111.2.2.1.80

nqaAdminParaLspVersion

INTEGER

{

  • draft6(1)
  • rfc4379(2)
  • ptnmode(3)
  • compatiblemode(4)

}

Read-write

The value of this object identifies the LSP version of a protocol.

The default value is draft6(1).

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.111.2.2.1.90

nqaAdminParaNextHopAddressType

InetAddressType

Read-write

This object indicates the type of a next hop address.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.111.2.2.1.91

nqaAdminParaNextHopAddress

InetAddress

Read-write

This object indicates the next-hop address.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.111.2.2.1.92

nqaAdminParaForwardingSimulationInboundIfIndex InterfaceIndexOrZero

Read-write

This object indicates the inbound interface to simulate product forwarding.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.111.2.2.1.100

nqaAdminParaSnmpCommunityRead

OCTET STRING(SIZE(0..32))

Read-write

This object indicates the community name for SNMP test.

This object is implemented as defined in the corresponding MIB file.

Creation Restriction

No entry can be created in this table.

Modification Restriction

  • This table is generated after test instances are created through nqaAdminCtrlTable. Therefore, to modify this table, you must specify nqaAdminCtrlOwnerIndex and nqaAdminCtrlTestName.

  • The test instance cannot be modified when it is running. To modify the test instance, you must stop the test instance first.

  • If the value of nqaGroupStatusType in nqaGroupTable for a test instance is member(2), that is, if the test instance is a group member, you can only set the values of the following objects:

    • nqaAdminParaTargetAddressType

    • nqaAdminParaTargetAddress

    • nqaAdminParaTargetPort

    • nqaAdminParaSourceAddressType

    • nqaAdminParaSourceAddress

    • nqaAdminParaSourcePort

    • nqaAdminParaDataSize

    • nqaAdminParaIfIndex

  • If the value of nqaGroupStatusType in nqaGroupTable for a test instance is leader(1). If the test instance is a group leader, you cannot set the values of the following objects:

    • nqaAdminParaTargetAddressType

    • nqaAdminParaTargetAddress

    • nqaAdminParaTargetPort

    • nqaAdminParaSourceAddressType

    • nqaAdminParaSourceAddress

    • nqaAdminParaSourcePort

  • The nqaAdminParaEthPriority object can be separately configured. However, the nqaAdminParaEthPriorityStatus object can be configured only when it is bound to the nqaAdminParaEthPriority object.

  • The value of the nqaAdminParaEthPriority object can be cleared only when the value of the nqaAdminParaEthPriorityStatus object is disabled(2) and the value of the nqaAdminParaEthPriority object is 0.

After configuring the nqaAdminParaLspPathType object, you must configure the nqaAdminParaForwardingSimulationInboundIfIndex object for starting the test instance.

Deletion Restriction

The entries in this table cannot be deleted.

Access Restriction

The entries in this table can be read without restriction.

Translation
Download
Updated: 2019-07-19

Document ID: EDOC1000174090

Views: 500370

Downloads: 49

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next