No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

MIB Reference

AR100-S, AR110-S, AR120-S, AR150-S, AR160-S, AR200-S, AR1200-S, AR2200-S, and AR3200-S V200R009

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
ipv6IfTable

ipv6IfTable

This table is used to describe information about the IPv6 interface on the network device, including the index, description, identifier, and status.

The index of this table is ipv6IfIndex.

OID

Object Name

Syntax

Max Access

Description

Implemented Specifications

1.3.6.1.2.1.55.1.5.1.1

ipv6IfIndex

Ipv6IfIndex

Not-accessible

The value of the object is a unique non-zero value, which is used to identify a specified IPv6 interface.

The value ranges from 1 to 2147483647.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.2.1.55.1.5.1.2

ipv6IfDescr

DisplayString

Read-write

The field contains the text character string of port information. This string may be set by the network management system.

The value ranges from 1 to 242.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.2.1.55.1.5.1.3

ipv6IfLowerLayer

VariablePointer

Read-only

This object identifies the protocol layer over which this network interface operates.

If this network interface operates over the data-link layer, then the value of this object refers to an instance of ifIndex [6].

If this network interface operates over an IPv4 interface, the value of this object refers to an instance of ipAdEntAddr [3].

If this network interface operates over another IPv6 interface, the value of this object refers to an instance of ipv6IfIndex.

If this network interface is not currently operating over an active protocol layer, then the value of this object should be set to the OBJECT ID { 0 0 }.

Currently, only the value OBJECT ID { 0 0 } is supported.

1.3.6.1.2.1.55.1.5.1.4

ipv6IfEffectiveMtu

Unsigned32

Read-only

The value of this object identifies the largest size of the IPv6 packets that can be sent and received on the interface, in octets.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.2.1.55.1.5.1.5

ipv6IfReasmMaxSize

Unsigned32(0..65535)

Read-only

The size of the largest IPv6 datagram which this entity can re-assemble from incoming IPv6 fragmented datagrams received on this interface.

Currently, only the maximum size 65535 is supported.

1.3.6.1.2.1.55.1.5.1.6

ipv6IfIdentifier

Ipv6AddressIfIdentifier

Read-write

The Interface Identifier for this interface that is (at least) unique on the link this interface is attached to.

The Interface Identifier is combined with an address prefix to form an interface address.

By default, the Interface Identifier is autoconfigured according to the rules of the link type this interface is attached to.

The value ranges from 0 to 8.

Currently, the maximum access is read-only.

1.3.6.1.2.1.55.1.5.1.7

ipv6IfIdentifierLength

INTEGER (0..64)

Read-write

The value of this object identifies the length of the interface identifier, in bits.

Currently, the maximum access is read-only; maximum length 64 is supported only.

1.3.6.1.2.1.55.1.5.1.8

ipv6IfPhysicalAddress

PhysAddress

Read-only

The interface's physical address. For example, for an IPv6 interface attached to an 802.x link, this object normally contains a MAC address.

Note that in some cases this address may differ from the address of the interface's protocol sub-layer. The interface's media-specific MIB must define the bit and byte ordering and the format of the value of this object.

For interfaces which do not have such an address (for example, a serial line), this object should contain an octet string of zero length.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.2.1.55.1.5.1.9

ipv6IfAdminStatus

INTEGER{up(1),down(2)}

Read-write

The value of this object identifies the desired status of the interface.

When a managed system initializes, all IPv6 interfaces start with ipv6IfAdminStatus in the down(2) state.

As a result of either explicit management action or per configuration information retained by the managed system, ipv6IfAdminStatus is then changed to the up(1) state (or remains in the down(2) state).

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.2.1.55.1.5.1.10

ipv6IfOperStatus

INTEGER{up(1),down(2),noIfIdentifier(3),unknown(4),notPresent(5)}

Read-only

The value of this object identifies the current operating status of this interface.

The noIfIdentifier(3) state indicates that no valid Interface Identifier is assigned to the interface.

This state usually indicates that the link-local interface address failed Duplicate Address Detection.

If ipv6IfAdminStatus is down(2) then ipv6IfOperStatus should be down(2).

If ipv6IfAdminStatus is changed to up(1) then ipv6IfOperStatus should change to up(1) if the interface is ready to transmit and receive network traffic; it should remain in the down(2) or noIfIdentifier(3) state if and only if there is a fault that prevents it from going to the up(1) state; it should remain in the notPresent(5) state if the interface has missing (typically, lower layer) components.

Currently, only the statuses up(1) and down(2) are supported.

1.3.6.1.2.1.55.1.5.1.11

ipv6IfLastChange

TimeStamp

Read-only

The value of sysUpTime at the time the interface entered its current operational state.

If the current state was entered prior to the last re-initialization of the local network management subsystem, then this object contains a zero value.

This object is implemented as defined in the corresponding MIB files.

Creation Restriction

No entry can be created in this table.

Modification Restriction

The entries in this table cannot be modified.

Deletion Restriction

The entries in this table cannot be deleted.

Access Restriction

The interface supports the IPv6 function.

Translation
Download
Updated: 2019-07-19

Document ID: EDOC1000174090

Views: 481520

Downloads: 48

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next