No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

AR100-S, AR110-S, AR120-S, AR150-S, AR160-S, AR200-S, AR1200-S, AR2200-S, and AR3200-S V200R009 CLI-based Configuration Guide - Ethernet Switching

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Adding Member Interfaces to an Eth-Trunk

Adding Member Interfaces to an Eth-Trunk

Context

You can add member interfaces to an Eth-Trunk in the Eth-Trunk interface view or member interface view.

NOTE:

The 4GE-2S, 4ES2G-S, 4ES2GP-S, and 9ES2 cards do not support the member interfaces of multiple Eth-Trunks deployed on different cards.

Procedure

  • Add member interfaces to an Eth-Trunk in the Eth-Trunk interface view.
    1. Run system-view

      The system view is displayed.

    2. Run interface eth-trunk trunk-id

      The Eth-Trunk interface view is displayed.

    3. Run trunkport interface-type { interface-number1 [ to interface-number2 ] } &<1-8>

      A member interface is added to the Eth-Trunk.

      NOTE:

      When you add member interfaces to an Eth-Trunk in a batch, if one interface cannot be added to the Eth-Trunk, interfaces with smaller IDs are added to the Eth-Trunk successfully but those with larger IDs will fail to be added.

  • Add member interfaces to an Eth-Trunk in the member interface view.
    1. Run system-view

      The system view is displayed.

    2. Run interface interface-type interface-number

      The member interface view is displayed.

    3. Run eth-trunk trunk-id

      The member interface is added to an Eth-Trunk.

    When adding an interface to an Eth-Trunk, pay attention to the following points:

    • An Eth-Trunk contains a maximum of 8 member interfaces.

    • A member interface cannot be configured with some services or static MAC addresses.
    • When adding an interface to an Eth-Trunk, ensure that the interface uses the default link type.
    • An Eth-Trunk cannot be added to another Eth-Trunk.
    • An Ethernet interface can be added to only one Eth-Trunk. To add the Ethernet interface to another Eth-Trunk, delete it from the Eth-Trunk first.
    • Member interfaces of an Eth-Trunk must use the same type.
    • If an interface of the local device is added to an Eth-Trunk, an interface of the remote device directly connected to the interface of the local device must also be added to an Eth-Trunk so that the two ends can communicate.
    • After interfaces are added to an Eth-Trunk, the Eth-Trunk learns MAC addresses and ARP entries but member interfaces do not.
    • Devices at both ends of an Eth-Trunk must use the same number of physical interfaces, interface rate, duplex mode, flow control mode and jumbo.

Follow-up Procedure

You can configure Eth-Trunk member interfaces to send trap messages after the Eth-Trunk member interface status changes. After the device receives a trap message, check whether the device fails or recovers.

If you need to know the status change of the member interface of a specified Eth-Trunk, run the trunk-member trap in private-mib enable command to enable Eth-Trunk member interfaces to use the proprietary MIB to send trap messages. The trap messages sent by using the proprietary MIB carry Eth-Trunk IDs, whereas the trap messages sent by using the public MIB do not carry Eth-Trunk IDs.

NOTE:

After the trunk-member trap in private-mib enable command is configured, Eth-Trunk member interfaces only use the proprietary MIB to send trap messages. To view these trap messages, use the Huawei proprietary MIB.

Translation
Download
Updated: 2019-05-17

Document ID: EDOC1000174108

Views: 56758

Downloads: 42

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next