No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

FusionStorage V100R006C10 File Storage Service Software Installation Guide 06

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring an IP Address for the Mgmt Port of a Storage Node

Configuring an IP Address for the Mgmt Port of a Storage Node

Prerequisites

You have installed ipmitool 1.8.14 or later, which is required when you configure IPv6 addresses using commands.

Procedure

  • To configure an IPv4 address, perform the following steps:
    1. Based on the live network environment, log in to a storage node by referring to the corresponding content for logging in to the corresponding node in the appendix of this document.
    2. Run ipmitool lan set 1 ipaddr xx.xx.xx.xx to set the IP address.
    3. Run ipmitool lan set 1 netmask xx.xx.xx.xx to set the subnet netmask.
    4. Run ipmitool lan set 1 defgw ipaddr xx.xx.xx.xx to set a default gateway.
    5. Run ipmitool lan print 1 to view the network settings.

      If you cannot access the Mgmt network, run the ipmitool bmc reset cold command to restart the Mgmt network service.

  • To configure an IPv6 address, perform the following steps:
    1. Based on the live network environment, log in to a storage node by referring to the corresponding content for logging in to the corresponding node in the appendix of this document.
    2. Run the ipmitool raw 0x0c 0x01 0x01 0x33 0x02 command to allow coexistence of IPv4 and IPv6 addresses.

      If only an IPv4 address is required, run the ipmitool raw 0x0c 0x01 0x01 0x33 0x00 command. If only an IPv6 address is required, run the ipmitool raw 0x0c 0x01 0x01 0x33 0x01 command.

    3. Run the ipmitool raw 0x0c 0x01 0x01 0x33 0x01 command to enable manual IPv6 address configuration.
    4. Run the ipmitool raw 0x0c 0x01 0x01 0xcc 0xdb 0x07 0x00 0x11 0x63 0x09 0xfe 0xff 0x82 0x18 0x02 0x00 0x00 0x00 0x00 0x00 0x00 0xc0 0xfe command to configure an IPv6 address.

      Among which, 0x11 0x63 0x09 0xfe 0xff 0x82 0x18 0x02 0x00 0x00 0x00 0x00 0x00 0x00 0xc0 0xfe consists of 16 groups of 8 bits, indicating IPv6 address fec0::218:82ff:fe09:6311/64.

    5. Run the ipmitool raw 0x0c 0x01 0x01 0xcd 0xdb 0x07 0x00 0x40 command to set the prefix of the IPv6 address.

      Among which, 0x40 is a hexadecimal value, corresponding to binary 64.

    6. Run the ipmitool raw 0x0c 0x01 0x01 0xce 0xdb 0x07 0x00 0x01 0x00 0x09 0xfe 0xff 0x82 0x18 0x02 0x00 0x00 0x00 0x00 0x00 0x00 0xc0 0xfe command to set the gateway.

      Among which, 0x01 0x00 0x09 0xfe 0xff 0x82 0x18 0x02 0x00 0x00 0x00 0x00 0x00 0x00 0xc0 0xfe indicates the gateway IP address fec0::218:82ff:fe09:1.

    7. Run the following commands to query the configurations of an IPv6 address:

      1. Run the ipmitool raw 0x0c 0x02 0x01 0xcc 0x00 0x00 to query the IPv6 address. The IP address starts from the fifth byte in the command return.
        Euler:~# ipmitool raw 0x0c 0x02 0x01 0xcc 0x00 0x00 l1 db 07 00 11 63 09 fe ff 82 18 02 00 00 00 00 00 00 c0 fe 
      2. Run the ipmitool raw 0x0c 0x02 0x01 0xcd 0x00 0x00 to query the prefix of the IPv6 address. The fifth byte in the command return indicates the prefix.
        Euler:~# ipmitool raw 0x0c 0x02 0x01 0xcd 0x00 0x00 l1 db 07 00 40
      3. Run the ipmitool raw 0x0c 0x02 0x01 0xce 0x00 0x00 to query the gateway of the IPv6 address. The gateway IP address starts from the fifth byte in the command return.
        Euler:~# ipmitool raw 0x0c 0x02 0x01 0xce 0x00 0x00 l1 db 07 00 01 00 09 fe ff 82 18 02 00 00 00 00 00 00 c0 fe
      NOTE:

      If you want to delete the IPv6 configurations, run the ipmitool raw 0x0c 0x01 0x01 0x33 0x00 command to set the system to be enabled with IPv4 only. Configurations related to IPv6 will be deleted.

  • To configure an IP address in BIOS mode, perform the following steps:
    1. Based on the live network environment, log in to a storage node by referring to the corresponding content for logging in to the corresponding node in the appendix of this document.
    2. Run the reboot command.
    3. During the restart process, if information similar to that in Figure 8-3 is displayed, press Delete. The BIOS screen is displayed.

      NOTE:

      The BIOS startup page appears soon after the figure as shown in Figure 8-4. Pay attention to the BIOS startup page because it appears for a short time.

      If you miss the BIOS startup page, click the Power Management icon (the third one from left to right) in the tool bar, and choose Forced System Reset. The Select an Option dialog box is displayed. Click Yes to restart the node.

      Figure 8-2  System restart prompt
      Figure 8-3  BIOS startup page

    4. Enter the BIOS password (default password: Huawei12#$) and press Enter. A message prompting you to modify your password is displayed. Press Enter.

      NOTE:
      • If you type an incorrect password three times, the system locks your account. In this case, you can click the Power Management icon, and choose Forced System Reset to restart the system.

      • For security purposes, you are advised to change the default password at your first login.

      • Do not use F9 to restore the BIOS default settings and not enable the NUMA function in the BIOS.

    5. Choose Advanced > IPMI iBMC Configuration > iBMC Configuration, as shown in Figure 8-4.

      Figure 8-4  Configuring an IP address for the Mgmt port

    6. Press F10 and select yes to save configurations and exit the BIOS setting page.
Translation
Download
Updated: 2019-03-28

Document ID: EDOC1000175257

Views: 8905

Downloads: 3

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next