No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S600-E V200R011C10 Configuration Guide - Network Management and Monitoring

This document provides the configurations of network management and monitoring features supported by the product, including SNMP, RMON, LLDP, NQA, Service Diagnosis, Mirroring, Packet Capture, and sFlow.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Example for Configuring a UDP Jitter Test Instance

Example for Configuring a UDP Jitter Test Instance

Networking Requirements

In Figure 4-25, a UDP jitter test needs to be performed to obtain the jitter time of transmitting a packet from SwitchA to SwitchC.

Figure 4-25  Networking diagram for configuring a jitter test instance

Configuration Roadmap

The configuration roadmap is as follows:

  1. Configure SwitchA as an NQA client and configure SwitchC as an NQA server.

  2. Configure the monitoring service type and port number on the NQA server.

  3. Create a UDP jitter test instance on the NQA client.

Procedure

  1. Configure an IP address for each interface and ensure reachable routes between switches.

    # Configure SwitchA.

    <HUAWEI> system-view
    [HUAWEI] sysname SwitchA
    [SwitchA] vlan 100
    [SwitchA-vlan100] quit
    [SwitchA] interface gigabitethernet 0/0/1
    [SwitchA-GigabitEthernet0/0/1] port link-type hybrid
    [SwitchA-GigabitEthernet0/0/1] port hybrid pvid vlan 100
    [SwitchA-GigabitEthernet0/0/1] port hybrid untagged vlan 100
    [SwitchA-GigabitEthernet0/0/1] quit
    [SwitchA] interface vlanif 100
    [SwitchA-Vlanif100] ip address 10.1.1.1 24
    [SwitchA-Vlanif100] quit
    [SwitchA] ip route-static 10.2.1.0 255.255.255.0 10.1.1.2

    # Configure SwitchB.

    <HUAWEI> system-view
    [HUAWEI] sysname SwitchB
    [SwitchB] vlan 100
    [SwitchB-vlan100] quit
    [SwitchB] vlan 110
    [SwitchB-vlan110] quit
    [SwitchB] interface gigabitethernet 0/0/1
    [SwitchB-GigabitEthernet0/0/1] port link-type hybrid
    [SwitchB-GigabitEthernet0/0/1] port hybrid pvid vlan 100
    [SwitchB-GigabitEthernet0/0/1] port hybrid untagged vlan 100
    [SwitchB-GigabitEthernet0/0/1] quit
    [SwitchB] interface vlanif 100
    [SwitchB-Vlanif100] ip address 10.1.1.2 24
    [SwitchB-Vlanif100] quit
    [SwitchB] interface gigabitethernet 0/0/2
    [SwitchB-GigabitEthernet0/0/2] port link-type hybrid
    [SwitchB-GigabitEthernet0/0/2] port hybrid pvid vlan 110
    [SwitchB-GigabitEthernet0/0/2] port hybrid untagged vlan 110
    [SwitchB-GigabitEthernet0/0/2] quit
    [SwitchB] interface vlanif 110
    [SwitchB-Vlanif110] ip address 10.2.1.1 24
    [SwitchB-Vlanif110] quit
    

    # Configure SwitchC.

    <HUAWEI> system-view
    [HUAWEI] sysname SwitchC
    [SwitchC] vlan 110
    [SwitchC-vlan110] quit
    [SwitchC] interface gigabitethernet 0/0/1
    [SwitchC-GigabitEthernet0/0/1] port link-type hybrid
    [SwitchC-GigabitEthernet0/0/1] port hybrid pvid vlan 110
    [SwitchC-GigabitEthernet0/0/1] port hybrid untagged vlan 110
    [SwitchC-GigabitEthernet0/0/1] quit
    [SwitchC] interface vlanif 110
    [SwitchC-Vlanif110] ip address 10.2.1.2 24
    [SwitchC-Vlanif110] quit
    [SwitchC] ip route-static 10.1.1.0 255.255.255.0 10.2.1.1

  2. Configure an NQA server on SwitchC.

    # Configure the monitoring IP address and UDP port number on the NQA server.

    [SwitchC] nqa-server udpecho 10.2.1.2 9000

  3. Configure SwitchA.

    # Enable the NQA client and create a UDP jitter test instance.

    [SwitchA] nqa test-instance admin jitter
    [SwitchA-nqa-admin-jitter] test-type jitter
    [SwitchA-nqa-admin-jitter] destination-address ipv4 10.2.1.2
    [SwitchA-nqa-admin-jitter] destination-port 9000 

  4. Start the test instance.

    [SwitchA-nqa-admin-jitter] start now

  5. Check the configuration.

    [SwitchA-nqa-admin-jitter] display nqa results test-instance admin jitter
     NQA entry(admin, jitter) :testflag is inactive ,testtype is jitter
      1 . Test 1 result   The test is finished                                      
       SendProbe:60                         ResponseProbe:60                        
       Completion:success                   RTD OverThresholds number:0             
       Min/Max/Avg/Sum RTT:1/80/6/331       RTT Square Sum:9341                     
       NumOfRTT:60                          Drop operation number:0                 
       Operation sequence errors number:0   RTT Stats errors number:0               
       System busy operation number:0       Operation timeout number:0              
       Min Positive SD:10                   Min Positive DS:10                      
       Max Positive SD:40                   Max Positive DS:40                      
       Positive SD Number:10                Positive DS Number:6                    
       Positive SD Sum:130                  Positive DS Sum:100                     
       Positive SD Square Sum:2500          Positive DS Square Sum:2400             
       Min Negative SD:10                   Min Negative DS:10                      
       Max Negative SD:40                   Max Negative DS:30                      
       Negative SD Number:9                 Negative DS Number:7                    
       Negative SD Sum:130                  Negative DS Sum:100                     
       Negative SD Square Sum:2700          Negative DS Square Sum:1800             
       Min Delay SD:0                       Min Delay DS:0                          
       Avg Delay SD:2                       Avg Delay DS:2                          
       Max Delay SD:40                      Max Delay DS:39                         
       Packet Loss SD:0                     Packet Loss DS:0                        
       Packet Loss Unknown:0                Average of Jitter:14                    
       Average of Jitter SD:13              Average of Jitter DS:15                 
       Jitter out value:2.5940387           Jitter in value:2.1560009               
       NumberOfOWD:60                       OWD SD Sum:145                          
       OWD DS Sum:126                       TimeStamp unit: ms                      
       Packet Rewrite Number: 0             Packet Rewrite Ratio: 0%                
       Packet Disorder Number: 0            Packet Disorder Ratio: 0%               
       Fragment-disorder Number: 0          Fragment-disorder Ratio: 0% 
       Start time: 2014-09-01 10:47:57+08:00                                                                                            
       End time: 2014-09-01 10:48:01+08:00  

Configuration Files

  • SwitchA configuration file

    #
    sysname SwitchA
    #
    vlan batch 100
    #
    interface Vlanif100
     ip address 10.1.1.1 255.255.255.0
    #
    interface GigabitEthernet0/0/1
     port link-type hybrid
     port hybrid pvid vlan 100
     port hybrid untagged vlan 100
    #
    ip route-static 10.2.1.0 255.255.255.0 10.1.1.2
    #
    nqa test-instance admin jitter
     test-type jitter
     destination-address ipv4 10.2.1.2
     destination-port 9000
    #
    return
  • SwitchB configuration file

    #
    sysname SwitchB
    #
    vlan batch 100 110
    #
    interface Vlanif100
     ip address 10.1.1.2 255.255.255.0
    #
    interface Vlanif110
     ip address 10.2.1.1 255.255.255.0
    #
    interface GigabitEthernet0/0/1
     port link-type hybrid
     port hybrid pvid vlan 100
     port hybrid untagged vlan 100
    #
    interface GigabitEthernet0/0/2
     port link-type hybrid
     port hybrid pvid vlan 110
     port hybrid untagged vlan 110
    #
    return
  • SwitchC configuration file

    #
    sysname SwitchC
    #
    vlan batch 110
    #
    interface Vlanif110
     ip address 10.2.1.2 255.255.255.0
    #
    interface GigabitEthernet0/0/1
     port link-type hybrid
     port hybrid pvid vlan 110
     port hybrid untagged vlan 110
    #
    nqa-server udpecho 10.2.1.2 9000
    #
    ip route-static 10.1.1.0 255.255.255.0 10.2.1.1
    #
    return
Translation
Download
Updated: 2019-09-23

Document ID: EDOC1000178020

Views: 73996

Downloads: 8

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next