No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S600-E V200R011C10 Configuration Guide - Network Management and Monitoring

This document provides the configurations of network management and monitoring features supported by the product, including SNMP, RMON, LLDP, NQA, Service Diagnosis, Mirroring, Packet Capture, and sFlow.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Example for Configuring the MAC Ping Test

Example for Configuring the MAC Ping Test

Networking Requirements

In Figure 4-27:

  • CFM is enabled on Switch A and Switch B.

  • MAs and MDs are configured on Switch A and Switch B.

The NQA MAC ping test is used to test the connectivity between Switch A and Switch B.

Figure 4-27  Networking diagram for configuring the MAC ping test

Configuration Roadmap

The configuration roadmap is as follows:

  1. Configure Switch A as the NQA client.

  2. Configure Switch B as the NQA server.

  3. Create a MAC ping test on Switch A.

Procedure

  1. Configure the MA and MD between Switch A and Switch B.

    # Configure Switch A.

    <HUAWEI> system-view
    [HUAWEI] sysname SwitchA
    [SwitchA] vlan batch 11
    [SwitchA] interface gigabitethernet 0/0/1
    [SwitchA-GigabitEthernet0/0/1] port link-type hybrid
    [SwitchA-GigabitEthernet0/0/1] port hybrid pvid vlan 11
    [SwitchA-GigabitEthernet0/0/1] port hybrid untagged vlan 11
    [SwitchA-GigabitEthernet0/0/1] quit
    [SwitchA] cfm enable
    [SwitchA] cfm md test
    [SwitchA-md-test] ma test
    [SwitchA-md-test-ma-test] map vlan 11
    [SwitchA-md-test-ma-test] mep mep-id 11 interface gigabitethernet0/0/1 outward
    [SwitchA-md-test-ma-test] mep ccm-send mep-id 11 enable
    [SwitchA-md-test-ma-test] remote-mep mep-id 12
    [SwitchA-md-test-ma-test] remote-mep ccm-receive mep-id 12 enable
    [SwitchA-md-test-ma-test] quit
    [SwitchA-md-test] quit

    # Configure Switch B.

    <HUAWEI> system-view
    [HUAWEI] sysname SwitchB
    [SwitchB] vlan batch 11
    [SwitchB] interface gigabitethernet 0/0/1
    [SwitchB-GigabitEthernet0/0/1] port link-type hybrid
    [SwitchB-GigabitEthernet0/0/1] port hybrid pvid vlan 11
    [SwitchB-GigabitEthernet0/0/1] port hybrid untagged vlan 11
    [SwitchB-GigabitEthernet0/0/1] quit
    [SwitchB] cfm enable
    [SwitchB] cfm md test
    [SwitchB-md-test] ma test
    [SwitchB-md-test-ma-test] map vlan 11
    [SwitchB-md-test-ma-test] mep mep-id 12 interface gigabitethernet0/0/1 outward
    [SwitchB-md-test-ma-test] mep ccm-send mep-id 12 enable
    [SwitchB-md-test-ma-test] remote-mep mep-id 11
    [SwitchB-md-test-ma-test] remote-mep ccm-receive mep-id 11 enable
    [SwitchB-md-test-ma-test] quit
    [SwitchB-md-test] quit

  2. # Enable the NQA client and create a MAC ping test for a common tunnel on Switch A.

    [SwitchA]nqa test-instance admin macping
    [SwitchA-nqa-admin-macping] test-type macping
    [SwitchA-nqa-admin-macping] md test ma test
    [SwitchA-nqa-admin-macping] destination-address remote-mep mep-id 12

  3. Perform the test.

    [SwitchA-nqa-admin-macping] start now

  4. Verify the test result.

    [SwitchA-nqa-admin-macping] display nqa results test-instance admin macping
    
     NQA entry(admin, macping) :testflag is inactive ,testtype is macping
      1 . Test 1 result   The test is finished
       SendProbe:3                          ResponseProbe:3
       Completion:success                   RTD OverThresholds number:0
       Min/Max/Avg/Sum RTT:3/3/3/9          RTT Square Sum:27
       NumOfRTT:3                           Drop operation number:0
       Operation sequence errors number:0   RTT Stats errors number:0
       System busy operation number:0       Operation timeout number:0
       Min Positive SD:0                    Min Positive DS:0
       Max Positive SD:0                    Max Positive DS:0
       Positive SD Number:0                 Positive DS Number:0
       Positive SD Sum:0                    Positive DS Sum:0
       Positive SD Square Sum:0             Positive DS Square Sum:0
       Min Negative SD:0                    Min Negative DS:0
       Max Negative SD:0                    Max Negative DS:0
       Negative SD Number:0                 Negative DS Number:0
       Negative SD Sum:0                    Negative DS Sum:0
       Negative SD Square Sum:0             Negative DS Square Sum:0
       Min Delay SD:0                       Min Delay DS:0
       Avg Delay SD:0                       Avg Delay DS:0
       Max Delay SD:0                       Max Delay DS:0
       Packet Loss SD:0                     Packet Loss DS:0
       Packet Loss Unknown:0                Average of Jitter:0
       Average of Jitter SD:0               Average of Jitter DS:0
       Jitter out value:0.0000000           Jitter in value:0.0000000
       NumberOfOWD:0                        OWD SD Sum:0  
       OWD DS Sum:0                         TimeStamp unit: ms   
       Packet Rewrite Number: 0             Packet Rewrite Ratio: 0% 
       Packet Disorder Number: 0            Packet Disorder Ratio: 0%  
       Fragment-disorder Number: 0          Fragment-disorder Ratio: 0%  
       Start time: --
       End time: --  

Configuration Files

  • SwitchA configuration file

    #
    sysname SwitchA
    #
    vlan batch 11
    #
    cfm enable
    #
    interface GigabitEthernet0/0/1
     port link-type hybrid
     port hybrid pvid vlan 11
     port hybrid untagged vlan 11
    #
    cfm md test
     ma test
      map vlan 11
      mep mep-id 11 interface GigabitEthernet0/0/1 outward
      mep ccm-send mep-id 11 enable
      remote-mep mep-id 12
      remote-mep ccm-receive mep-id 12 enable
    #
    nqa test-instance admin macping
     test-type macping
     destination-address remote-mep mep-id 12
     md test ma test
    #
    return
  • SwitchB configuration file

    #
    sysname SwitchB
    #
    vlan batch 11
    #
    cfm enable
    #
    interface GigabitEthernet0/0/1
     port link-type hybrid
     port hybrid pvid vlan 11
     port hybrid untagged vlan 11
    #
    cfm md test
     ma test
      map vlan 11
      mep mep-id 12 interface GigabitEthernet0/0/1 outward
      mep ccm-send mep-id 12 enable
      remote-mep mep-id 11
      remote-mep ccm-receive mep-id 11 enable
    #
    return
Translation
Download
Updated: 2019-03-30

Document ID: EDOC1000178020

Views: 57313

Downloads: 7

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next