No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S600-E V200R011C10 Configuration Guide - Network Management and Monitoring

This document provides the configurations of network management and monitoring features supported by the product, including SNMP, RMON, LLDP, NQA, Service Diagnosis, Mirroring, Packet Capture, and sFlow.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Example for Configuring a UDP Test Instance

Example for Configuring a UDP Test Instance

Networking Requirements

In Figure 4-24, an NQA UDP test needs to be performed to obtain the RTT of a UDP packet transmitted between SwitchA and SwitchC.

Figure 4-24  Networking diagram for configuring a UDP test instance

Configuration Roadmap

The configuration roadmap is as follows:

  1. Configure SwitchA as an NQA client and configure SwitchC as an NQA server.

  2. Configure the port number monitored by the NQA server and create an NQA UDP test instance on the NQA client.

Procedure

  1. Configure an IP address for each interface and ensure reachable routes between switches.

    # Configure SwitchA.

    <HUAWEI> system-view
    [HUAWEI] sysname SwitchA
    [SwitchA] vlan 100
    [SwitchA-vlan100] quit
    [SwitchA] interface gigabitethernet 0/0/1
    [SwitchA-GigabitEthernet0/0/1] port link-type hybrid
    [SwitchA-GigabitEthernet0/0/1] port hybrid pvid vlan 100
    [SwitchA-GigabitEthernet0/0/1] port hybrid untagged vlan 100
    [SwitchA-GigabitEthernet0/0/1] quit
    [SwitchA] interface vlanif 100
    [SwitchA-Vlanif100] ip address 10.1.1.1 24
    [SwitchA-Vlanif100] quit
    [SwitchA] ip route-static 10.2.1.0 255.255.255.0 10.1.1.2

    # Configure SwitchB.

    <HUAWEI> system-view
    [HUAWEI] sysname SwitchB
    [SwitchB] vlan 100
    [SwitchB-vlan100] quit
    [SwitchB] vlan 110
    [SwitchB-vlan110] quit
    [SwitchB] interface gigabitethernet 0/0/1
    [SwitchB-GigabitEthernet0/0/1] port link-type hybrid
    [SwitchB-GigabitEthernet0/0/1] port hybrid pvid vlan 100
    [SwitchB-GigabitEthernet0/0/1] port hybrid untagged vlan 100
    [SwitchB-GigabitEthernet0/0/1] quit
    [SwitchB] interface vlanif 100
    [SwitchB-Vlanif100] ip address 10.1.1.2 24
    [SwitchB-Vlanif100] quit
    [SwitchB] interface gigabitethernet 0/0/2
    [SwitchB-GigabitEthernet0/0/2] port link-type hybrid
    [SwitchB-GigabitEthernet0/0/2] port hybrid pvid vlan 110
    [SwitchB-GigabitEthernet0/0/2] port hybrid untagged vlan 110
    [SwitchB-GigabitEthernet0/0/2] quit
    [SwitchB] interface vlanif 110
    [SwitchB-Vlanif110] ip address 10.2.1.1 24
    [SwitchB-Vlanif110] quit
    

    # Configure SwitchC.

    <HUAWEI> system-view
    [HUAWEI] sysname SwitchC
    [SwitchC] vlan 110
    [SwitchC-vlan110] quit
    [SwitchC] interface gigabitethernet 0/0/1
    [SwitchC-GigabitEthernet0/0/1] port link-type hybrid
    [SwitchC-GigabitEthernet0/0/1] port hybrid pvid vlan 110
    [SwitchC-GigabitEthernet0/0/1] port hybrid untagged vlan 110
    [SwitchC-GigabitEthernet0/0/1] quit
    [SwitchC] interface vlanif 110
    [SwitchC-Vlanif110] ip address 10.2.1.2 24
    [SwitchC-Vlanif110] quit
    [SwitchC] ip route-static 10.1.1.0 255.255.255.0 10.2.1.1

  2. Configure an NQA server on SwitchC.

    # Configure the monitoring IP address and UDP port number on the NQA server.

    [SwitchC] nqa-server udpecho 10.2.1.2 6000

  3. Configure the NQA client on SwitchA.

    # Enable the NQA client and create a UDP test instance.

    [SwitchA] nqa test-instance admin udp
    [SwitchA-nqa-admin-udp] test-type udp
    [SwitchA-nqa-admin-udp] destination-address ipv4 10.2.1.2
    [SwitchA-nqa-admin-udp] destination-port 6000

  4. Start the test instance.

    [SwitchA-nqa-admin-udp] start now

  5. Verify the configuration.

    [SwitchA-nqa-admin-udp] display nqa results test-instance admin udp 
    
     NQA entry(admin, udp) :testflag is inactive ,testtype is udp
      1 . Test 1 result   The test is finished                                      
       Send operation times: 3              Receive response times: 3               
       Completion:success                   RTD OverThresholds number: 0            
       Attempts number:1                    Drop operation number:0                 
       Disconnect operation number:0        Operation timeout number:0              
       System busy operation number:0       Connection fail number:0                
       Operation sequence errors number:0   RTT Status errors number:0              
       Destination ip address:10.2.1.2                                              
       Min/Max/Average Completion Time: 32/109/67                                       
       Sum/Square-Sum  Completion Time: 203/16749                                        
       Last Good Probe Time: 2012-07-25 16:23:49.1                                  
       Lost packet ratio: 0 %                      

Configuration Files

  • SwitchA configuration file

    #
    sysname SwitchA
    #
    vlan batch 100
    #
    interface Vlanif100
     ip address 10.1.1.1 255.255.255.0
    #
    interface GigabitEthernet0/0/1
     port link-type hybrid
     port hybrid pvid vlan 100
     port hybrid untagged vlan 100
    #
    ip route-static 10.2.1.0 255.255.255.0 10.1.1.2
    #
    nqa test-instance admin udp
     test-type udp
     destination-address ipv4 10.2.1.2
     destination-port 6000
    #
    return
  • SwitchB configuration file

    #
    sysname SwitchB
    #
    vlan batch 100 110
    #
    interface Vlanif100
     ip address 10.1.1.2 255.255.255.0
    #
    interface Vlanif110
     ip address 10.2.1.1 255.255.255.0
    #
    interface GigabitEthernet0/0/1
     port link-type hybrid
     port hybrid pvid vlan 100
     port hybrid untagged vlan 100
    #
    interface GigabitEthernet0/0/2
     port link-type hybrid
     port hybrid pvid vlan 110
     port hybrid untagged vlan 110
    #
    return
  • SwitchC configuration file

    #
    sysname SwitchC
    #
    vlan batch 110
    #
    interface Vlanif110
     ip address 10.2.1.2 255.255.255.0
    #
    interface GigabitEthernet0/0/1
     port link-type hybrid
     port hybrid pvid vlan 110
     port hybrid untagged vlan 110
    #
    nqa-server udpecho 10.2.1.2 6000
    #
    ip route-static 10.1.1.0 255.255.255.0 10.2.1.1
    #
    return
Translation
Download
Updated: 2019-03-30

Document ID: EDOC1000178020

Views: 62821

Downloads: 7

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next