No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S12700 V200R011C10 Configuration Guide - Network Management and Monitoring

This document provides the configurations of network management and monitoring features supported by the product, including SNMP, RMON and RMON2, LLDP, Performance Management, iPCA, NQA, Service Diagnosis, Mirroring, Packet Capture, Traffic Distribution, NetStream, sFlow, and TWAMP Light.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Example for Configuring ACL-based Local Traffic Mirroring

Example for Configuring ACL-based Local Traffic Mirroring

Networking Requirements

In Figure 8-17, the science and technology department and administrative department of a company use the network segments 10.1.1.0/24 and 10.1.2.0/24, respectively, to access the Internet or communicate with each other through the Switch. The monitoring device (Server) is directly connected to the Switch.

The following traffic from the science and technology department needs to be monitored by the Server:
  • Traffic to the Internet
  • Traffic to the administrative department
Figure 8-17  ACL-based local traffic mirroring networking

Configuration Roadmap

The configuration roadmap is as follows:
  1. Configure GE1/0/2 of the Switch as a local observing port to forward mirrored packets to the Server.
  2. Configure advanced ACLs to match two types of traffic of the science and technology department: Internet access traffic and traffic sent to the administrative department.
  3. Configure an ACL-based traffic policy on GE1/0/1 to mirror the matching traffic.

Procedure

  1. Configure an observing port.

    # Configure GE1/0/2 of the Switch as a local observing port.

    <HUAWEI> system-view
    [HUAWEI] sysname Switch
    [Switch] observe-port 1 interface gigabitethernet 1/0/2
    

  2. Configure advanced ACLs.

    # Create two advanced ACLs numbered 3000 and 3001 on the Switch, configure ACL 3000 to match traffic with source address 10.1.1.0/24 and destination TCP port number WWW, and configure ACL 3001 to match traffic with source address 10.1.1.0/24 and destination address 10.1.2.0/24.

    [Switch] acl number 3000
    [Switch-acl-adv-3000] rule permit tcp source 10.1.1.0 0.0.0.255 destination-port eq www
    [Switch-acl-adv-3000] quit
    [Switch] acl number 3001
    [Switch-acl-adv-3001] rule permit ip source 10.1.1.0 0.0.0.255 destination 10.1.2.0 0.0.0.255
    [Switch-acl-adv-3001] quit
    

  3. Configure an ACL-based traffic policy.

    # Configure an ACL-based traffic policy on GE1/0/1 of the Switch to mirror the matching traffic.

    [Switch] interface gigabitethernet 1/0/1
    [Switch-GigabitEthernet1/0/1] traffic-mirror inbound acl 3000 to observe-port 1
    [Switch-GigabitEthernet1/0/1] traffic-mirror inbound acl 3001 to observe-port 1
    [Switch-GigabitEthernet1/0/1] return

  4. Verify the configuration.

    # Check ACL rules and traffic behavior information.

    <Switch> display traffic-applied interface gigabitethernet 1/0/1 inbound
    -----------------------------------------------------------
    ACL applied inbound interface GigabitEthernet1/0/1
    
    ACL 3000
     rule 5 permit tcp source 10.1.1.0 0.0.0.255 destination-port eq www (match-counter 0)
    ACTIONS:
     mirror to observe-port 1
    -----------------------------------------------------------
    
    ACL 3001
     rule 5 permit ip source 10.1.1.0 0.0.0.255 destination 10.1.2.0 0.0.0.255 (match-counter 0)
    ACTIONS:
     mirror to observe-port 1
    -----------------------------------------------------------

    # Check the observing port configuration.

    <Switch> display observe-port
      ----------------------------------------------------------------------
      Index          : 1
      Untag-packet   : No
      Interface      : GigabitEthernet1/0/2
      ----------------------------------------------------------------------
    

    # Check the mirroring configuration.

    <Switch> display port-mirroring
      ----------------------------------------------------------------------
      Observe-port 1 : GigabitEthernet1/0/2
      ----------------------------------------------------------------------
      Stream-mirror:
      ----------------------------------------------------------------------
           Behavior                  Direction  Observe-port
      ----------------------------------------------------------------------
      1    SACL                      -          Observe-port 1
      ----------------------------------------------------------------------
    

Configuration Files

  • Switch configuration file

    #
    sysname Switch
    #
    observe-port 1 interface GigabitEthernet1/0/2
    #
    acl number 3000
     rule 5 permit tcp source 10.1.1.0 0.0.0.255 destination-port eq www
    acl number 3001
     rule 5 permit ip source 10.1.1.0 0.0.0.255 destination 10.1.2.0 0.0.0.255
    #
    interface GigabitEthernet1/0/1
     traffic-mirror inbound acl 3000 to observe-port 1
     traffic-mirror inbound acl 3001 to observe-port 1
    #
    return
    
Translation
Download
Updated: 2019-10-21

Document ID: EDOC1000178113

Views: 135635

Downloads: 53

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next