No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Device Management

S1720, S2700, S5700, and S6720 V200R011C10

This document describes the principles and configurations of the Device Management features, and provides configuration examples of these features.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuration Examples for PoE

Configuration Examples for PoE

Networking Requirements

In Figure 8-3, the switch is deployed at the access layer on the network. The IP phones connected to the switch are deployed outdoors and APs are deployed on the external wall of the office. It is difficult to connect power supplies to these devices. The user wants the switch to provide power for these devices and save deployment costs.

AP1 provides wireless access to the office network of the bank, and so it cannot be powered off and requires the highest power supply priority. IP Phone1 processes heavy service traffic, and so it requires a high power supply priority and cannot be powered off.

Figure 8-3  Networking diagram of the PoE application

Configuration Roadmap

The switch must support PoE and have PoE power supplies installed.

The configuration roadmap is as follows:

  1. Configure the power supply priority on GigabitEthernet0/0/2 and GigabitEthernet0/0/1 so that AP1 and IP phone1 are provided with power preferentially.
  2. Configure the maximum output power on GigabitEthernet0/0/1, GigabitEthernet0/0/3, and GigabitEthernet0/0/2 to limit the power of these interfaces and prevent damage to the device.

Procedure

  1. Set the maximum output power on GigabitEthernet0/0/1, GigabitEthernet0/0/3, and GigabitEthernet0/0/2 to 15 W, 15 W, and 20 W respectively. Output power is measured in mW on the device.

    <HUAWEI> system-view
    [HUAWEI] sysname Switch
    [Switch] interface gigabitethernet 0/0/1
    [Switch-GigabitEthernet0/0/1] poe power 15000
    [Switch-GigabitEthernet0/0/1] quit
    [Switch] interface gigabitethernet 0/0/3
    [Switch-GigabitEthernet0/0/3] poe power 15000
    [Switch-GigabitEthernet0/0/3] quit
    [Switch] interface gigabitethernet 0/0/2
    [Switch-GigabitEthernet0/0/2] poe power 20000
    [Switch-GigabitEthernet0/0/2] quit

  2. Set the power supply priority on GigabitEthernet0/0/2 to critical.

    [Switch] interface gigabitethernet 0/0/2
    [Switch-GigabitEthernet0/0/2] poe priority critical
    [Switch-GigabitEthernet0/0/2] quit

  3. Set the power supply priority on GigabitEthernet0/0/1 to high.

    [Switch] interface gigabitethernet 0/0/1
    [Switch-GigabitEthernet0/0/1] poe priority high
    [Switch-GigabitEthernet0/0/1] quit

  4. Verify the configuration.

    # Check the PoE power supply status of the interface on the device.

    [Switch] display poe power-state
    PORTNAME                 POWERON/OFF  ENABLED  PRIORITY STATUS
    --------------------------------------------------------------------------------
    GigabitEthernet0/0/1     on           enable   high     Powered
    GigabitEthernet0/0/2     on           enable   Critical Powered
    GigabitEthernet0/0/3     on           enable   Low      Powered
    GigabitEthernet0/0/4     on           enable   Low      Powered
    GigabitEthernet0/0/5     off          enable   Low      Detecting
    GigabitEthernet0/0/6     off          enable   Low      Detecting
    GigabitEthernet0/0/7     off          enable   Low      Detecting
    GigabitEthernet0/0/8     off          enable   Low      Detecting
    GigabitEthernet0/0/9     off          enable   Low      Detecting
    GigabitEthernet0/0/10    off          enable   Low      Detecting
    GigabitEthernet0/0/11    off          enable   Low      Detecting
    GigabitEthernet0/0/12    off          enable   Low      Detecting
    GigabitEthernet0/0/13    off          enable   Low      Detecting
    GigabitEthernet0/0/14    off          enable   Low      Detecting
    GigabitEthernet0/0/15    off          enable   Low      Detecting
    GigabitEthernet0/0/16    off          enable   Low      Detecting
    GigabitEthernet0/0/17    off          enable   Low      Detecting
    GigabitEthernet0/0/18    off          enable   Low      Detecting
    GigabitEthernet0/0/19    off          enable   Low      Detecting
    GigabitEthernet0/0/20    off          enable   Low      Detecting
    GigabitEthernet0/0/21    off          enable   Low      Detecting
    GigabitEthernet0/0/22    off          enable   Low      Detecting
    GigabitEthernet0/0/23    off          enable   Low      Detecting
    GigabitEthernet0/0/24    off          enable   Low      Detecting

Configuration Files

#
sysname Switch
#
interface GigabitEthernet0/0/1
 poe priority high
 poe power 15000
#
interface GigabitEthernet0/0/2
 poe priority critical
 poe power 20000
#
interface GigabitEthernet0/0/3
 poe power 15000
#
return                         
Translation
Download
Updated: 2019-10-21

Document ID: EDOC1000178167

Views: 209040

Downloads: 1003

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next