S6720SI
|
40GE ports on the front panel and interface card |
- 1 m, 3 m, and 5 m QSFP+ passive high-speed copper cables
- QSFP+ optical module (QSFP-40G-SR-BD not supported) and optical
fiber
- 10 m QSFP+ AOC cable
|
40 Gbit/s |
- A stack can be set up between S6720SI models, but a stack cannot
be set up between S6720SI and S6720S-SI.
- When 40GE ports on the front panel are used as stack ports, a switch supports a maximum of two logical
stack ports, and each logical stack port supports a maximum of two
stack member ports. Each switch can use a maximum of two service ports
as stack member ports.
- When electrical ports or 10GE optical ports on the front panel
are used as stack ports, a switch supports a maximum
of two logical stack ports, and each logical stack port supports at
least one stack member port and at most eight stack member ports.
A switch supports a maximum of 16 stack member ports.
- Two types of ports among 40GE ports, 10GE optical ports,
and electrical ports on an S6720SI can both be configured as stack
member ports, but each logical stack port contains only the same type
of stack member ports.
- 40GE ports do not support the stacking function
after they are split into 10GE ports.
- If stack member ports on the front panel are
connected using 1 m, 3 m, or 5 m QSFP+ passive high-speed copper cables,
their working speed can be increased to 48 Gbit/s using the stack port speed command. After their working speed is
increased to 48 Gbit/s, switches using these ports cannot set up a
stack with switches using ports with the working speed 40 Gbit/s.
- Only the rate of 40GE interfaces on the front panel can be increased
to 48 Gbit/s.
- Only the last 16 10GE ports on the front panel
can be used to set up a stack using dedicated stack cables.
|
10GE optical ports on the front panel and interface card |
- 1 m, 3 m, and 5 m SFP+ passive high-speed copper cables
- 10 m SFP+ active high-speed copper cables
- 3 m and 10 m AOC cables
- 10GE SFP+ optical module and optical fiber
- 0.5 m and 1.5 m SFP+ dedicated stack cable (supported in V200R011C10
and later versions)
|
10 Gbit/s |
Electrical ports on the front panel |
Category 6A or higher network cables (If Category
6 cables are used, ensure that the cables meet requirements of TSB-155.)
|
10 Gbit/s |
S6720S-SI
|
40GE ports on the front panel |
- 1 m, 3 m, and 5 m QSFP+ passive high-speed copper cables
- QSFP+ optical module (QSFP-40G-SR-BD not supported) and optical
fiber
- 10 m QSFP+ AOC cable
|
40 Gbit/s |
- A stack can be set up between S6720S-SI models, but a stack cannot
be set up between S6720S-SI and S6720SI.
- When 40GE ports on the front panel are used as stack ports, a switch supports a maximum of two logical
stack ports, and each logical stack port supports a maximum of two
stack member ports. Each switch can use a maximum of two service ports
as stack member ports.
- When 10GE optical ports on the front panel are used as stack ports, a switch supports a maximum
of two logical stack ports, and each logical stack port supports at
least one stack member port and at most eight stack member ports.
A switch supports a maximum of 16 stack member ports.
- Two types of ports on an S6720S-SI can both be configured as stack
member ports, but each logical stack port contains only the same type
of stack member ports.
- 40GE ports do not support the stacking function
after they are split into 10GE ports.
- If stack member ports on the front panel are
connected using 1 m, 3 m, or 5 m QSFP+ passive high-speed copper cables,
their working speed can be increased to 48 Gbit/s using the stack port speed command. After their working speed is
increased to 48 Gbit/s, switches using these ports cannot set up a
stack with switches using ports with the working speed 40 Gbit/s.
- Only the last 16 10GE ports on the front panel
can be used to set up a stack using dedicated stack cables.
|
10GE optical ports on the front panel |
- 1 m, 3 m, and 5 m SFP+ passive high-speed copper cables
- 10 m SFP+ active high-speed copper cables
- 3 m and 10 m AOC cables
- 10GE SFP+ optical module and optical fiber
- 0.5 m and 1.5 m SFP+ dedicated stack cable (supported in V200R011C10
and later versions)
|
10 Gbit/s |