No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - IP Service

S1720, S2700, S5700, and S6720 V200R011C10

This document describes the configurations of IP Service, including IP address, ARP, DHCP, DHCP policy VLAN, DNS, mDNS gateway, mDNS relay, UDP Helper, IP performance optimization, IPv6, DHCPv6, IPv6 DNS, IPv6 over IPv4 tunnel, and IPv4 over IPv6 tunnel.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring Proxy ARP

Configuring Proxy ARP

Configuration Procedure

Perform the following configuration tasks in any sequence.

Configuring Routed Proxy ARP

Context

When an enterprise network is divided into subnets, two subnets may belong to the same network segment but different physical networks. These two subnets are connected by a switch but cannot communicate with each other. To allow data packets destined for other subnets to be sent to the gateway and subsequently forwarded to the destination, you can modify the routing information about the hosts on the network. However, to implement this solution, you must configure routes for all hosts on the subnets, which is time consuming. Deploying routed proxy ARP on the gateway effectively solves this problem.

Routed proxy ARP allows communication between hosts whose IP addresses belong to the same network segment but different physical networks. In addition, the default gateway does not need to be configured on the hosts, facilitating management and maintenance.

Figure 4-15 shows an example of routed proxy ARP networking. In the figure:
  • The Switch connects to two subnets through IF1 and IF2.
  • The IP addresses of IF1 and IF2 belong to different network segments.
  • The IP address of Host_1 in subnet 1 belongs to the same network segment as the IF1 IP address.
  • The IP address of Host_2 in subnet 2 belongs to the same network segment as the IF2 IP address
  • The IP address of Host_1 in subnet 1 belongs to the same network segment as that of Host_2.
  • The default gateway is not configured on Host_1 and Host_2.

To enable the hosts in subnets 1 and 2 to communicate with each other, configure routed proxy ARP on the Switch.

Figure 4-15  Networking diagram of routed proxy ARP

Procedure

  1. Run system-view

    The system view is displayed.

  2. Run interface interface-type interface-number

    The interface view is displayed.

  3. (Optional) On an Ethernet interface, run undo portswitch

    The interface is switched to Layer 3 mode.

    By default, an Ethernet interface works in Layer 2 mode.
    NOTE:

    Only the S5720HI, S5720EI, S6720EI, and S6720S-EI support switching between Layer 2 and Layer 3 modes.

  4. Run ip address ip-address { mask | mask-length }

    An IP address is configured for the interface.

    The interface IP address must reside on the same network segment as the IP addresses of the hosts connected to the interface.

  5. Run arp-proxy enable

    Routed proxy ARP is enabled on the interface.

    By default, routed proxy ARP is disabled on an interface.

    After routed proxy ARP is enabled on the device, the aging time of ARP entries on hosts must be reduced. This ensures that invalid ARP entries are aged as soon as possible, reducing the number of packets that are sent to, and cannot be forwarded by the Switch.

Verifying the Configuration

Run the display this command in the interface view to verify whether routed proxy ARP is enabled on the interface.

Configuring Intra-VLAN Proxy ARP

Context

Users in the same VLAN cannot communicate with each other when port isolation is configured in the VLAN. Configure intra-VLAN proxy ARP on the interfaces associated with the VLAN to enable Layer 3 communication among users.

Figure 4-16 shows an example of a network running intra-VLAN proxy ARP. Host_1 and Host_2 belong to the same VLAN, but port isolation is configured between IF1 and IF2 that connect the Switch to Host_1 and Host_2. Configure intra-VLAN proxy ARP on the Switch so that Host_1 and Host_2 can communicate with each other.

Figure 4-16  Networking diagram of intra-VLAN proxy ARP

In Figure 4-16, Host_1 and Host_2 belong to the same VLAN, but port isolation is configured between IF1 and IF2. Configure intra-VLAN proxy ARP on the Switch so that Host_1 and Host_2 can communicate with each other.

Procedure

  1. Run system-view

    The system view is displayed.

  2. Run interface interface-type interface-number

    The interface view is displayed.

  3. Run arp-proxy inner-sub-vlan-proxy enable

    Intra-VLAN proxy ARP is enabled.

    By default, intra-VLAN proxy ARP is disabled.

Verifying the Configuration

Run the display this command in the interface view to verify whether intra-VLAN proxy ARP is enabled.

Configuring Inter-VLAN Proxy ARP

Context

To implement Layer 3 communication among users on the same network segment but in different VLANs, enable inter-VLAN proxy ARP on the interface associated with the VLANs.

Figure 4-17 shows a network using inter-VLAN proxy ARP.

Figure 4-17  Networking diagram of inter-VLAN proxy ARP

In Figure 4-17, Host_1 and Host_2 belong to the same network segment but different VLANs. Inter-VLAN proxy ARP is enabled on the Switch so that Host_1 and Host_2 can communicate with each other.

You can also configure VLANIF interfaces to implement Layer 3 communication among users in different VLANs. For details, see Configuring Inter-VLAN Communication in "VLAN Configuration" in the S1720, S2700, S5700, and S6720 V200R011C10 Configuration Guide - Ethernet Switching.

NOTE:

Only the S5720SI, S5720S-SI, S5720EI, S5720HI, S5730SI, S5730S-EI, S6720SI, S6720S-SI, S6720EI, and S6720S-EI support the inter-VLAN proxy ARP.

Procedure

  1. Run system-view

    The system view is displayed.

  2. Run interface interface-type interface-number

    The interface view is displayed.

  3. Run arp-proxy inter-sub-vlan-proxy enable

    Inter-VLAN proxy ARP is enabled.

    By default, inter-VLAN proxy ARP is disabled.

Verifying the Configuration

Run the display this command in the interface view to verify whether inter-VLAN proxy ARP is enabled.

Translation
Download
Updated: 2019-03-28

Document ID: EDOC1000178170

Views: 174340

Downloads: 781

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next