Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document.
Note: Even the most advanced machine translation cannot match the quality of professional translators.
Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Verifying the Configuration of a Dynamic MPLS TE Tunnel
Procedure
- Run the display mpls te link-administration bandwidth-allocation [ interface interface-type interface-number ] command to check information about the allocated link bandwidth.
- Run the display ospf [ process-id ] mpls-te [ area area-id ] [ self-originated ] command to check information about OSPF TE.
- Run one of the following commands to check IS-IS TE information:
- display isis traffic-eng advertisements
- display isis traffic-eng link
- display isis traffic-eng network
- display isis traffic-eng statistics
- display isis traffic-eng sub-tlvs
- Run the display explicit-path [ [ name ] path-name ] [ tunnel-interface | lsp-attribute | verbose ] command to check configured explicit paths.
- Run the display mpls te cspf destination ip-address [ affinity properties [ mask mask-value ] | bandwidth { ct0 ct0-bandwidth | ct1 ct1-bandwidth } * | explicit-path path-name | hop-limit hop-limit-number | metric-type { igp | te } | priority setup-priority | srlg-strict exclude-path-name | tie-breaking { random | most-fill | least-fill } ] * [ hot-standby [ explicit-path path-name | overlap-path | affinity properties [ mask mask-value ] | hop-limit hop-limit-number | srlg { preferred | strict } ] * ] command to check information about a path that is calculated using CSPF based on specified conditions.
- Run the display mpls te cspf tedb { all | area { area-id | area-id-ip } | interface ip-address | network-lsa | node [ router-id ] | srlg srlg-number | overload-node } command to check information about TEDBs that can meet specified conditions and be used by CSPF to calculate paths.
- Run the display mpls rsvp-te command to check RSVP information.
- Run the display mpls rsvp-te established [ interface interface-type interface-number peer-ip-address ] command to check information about the established RSVP-TE CR-LSPs.
- Run the display mpls rsvp-te peer [ interface interface-type interface-number ] command to check RSVP neighbor parameters.
- Run the display mpls rsvp-te reservation [ interface interface-type interface-number peer-ip-address ] command to check information about RSVP resource reservation.
- Run the display mpls rsvp-te request [ interface interface-type interface-number peer-ip-address ] command to check information about the RSVP-TE request messages on interfaces.
- Run the display mpls rsvp-te sender [ interface interface-type interface-number peer-ip-address ] command to check information about RSVP senders.
- Run the display mpls rsvp-te statistics { global | interface [ interface-type interface-number ] } command to check RSVP-TE statistics.
- Run the display mpls te link-administration admission-control [ interface interface-type interface-number | stale-interface interface-index ] command to check the tunnels set up on the local node.
- Run the display mpls te tunnel [ destination ip-address ] [ lsp-id ingress-lsr-id session-id local-lsp-id ] [ lsr-role { all | egress | ingress | remote | transit } ] [ name tunnel-name ] [ { incoming-interface | interface | outgoing-interface } interface-type interface-number ] [ verbose ] command to check tunnel information.
- Run the display mpls te tunnel statistics or display mpls lsp statistics command to check tunnel statistics.
- Run the display lsp-attribute [ name lsp-attribute-name ] [ tunnel-interface | verbose ] command to check the configurations of the CR-LSP attribute template and the tunnels using it.
- Run the display mpls te tunnel-interface lsp-constraint [ tunnel interface-number ] command to view information about the CR-LSP attribute template on the TE tunnel interface.
- Run the display mpls te tunnel-interface [ tunnel interface-number | auto-bypass-tunnel [ tunnel-name ] ] command to check information about the MPLS TE tunnel.
- Run the display mpls te tunnel c-hop [ tunnel-name ] [ lsp-id ingress-lsr-id session-id lsp-id ] command to check path computation results of tunnels.
- Run the display mpls te session-entry [ ingress-lsr-id tunnel-id egress-lsr-id ] command to check detailed information about the LSP session entry.
