No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

MIB Reference

S7700 and S9700 V200R011C10

This document provides the function overview, relationships between tables, description of single objects, description of MIB tables, and description of alarm objects.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
HUAWEI-IF-EXT-MIB

HUAWEI-IF-EXT-MIB

Functions Overview

Huawei defines the HUAWEI-IF-EXT-MIB.

This MIB describes the following:

  • Extension attribute of the Layer 2 interface

  • IP configuration of the interface

  • IP address unnumbered

  • Attributes of the trunk interface and trunk member interface

  • Logical interface management

  • Higher and lower alarm thresholds for performance statistics

In this MIB, you can query and set the following:

  • Extension attributes of the interface

  • IP configuration of the interface, such as the IP address and the subnet mask

  • Attributes of the trunk interface and trunk member interface, such as the trunk interface type, interface mode, and selection of trunk member interfaces

The OID of the root object is:

iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).huawei(2011).huaweiMgmt(5).hwDatacomm(25).hwIFExtMib(41)

Relationship Between the Tables

Figure 57-1 shows the relationship among the tables.
Figure 57-1  Relationship among the tables of the HUAWEI-IF-EXT-MIB

Figure 57-1 describes the referential relation between ifTable and other tables in HUAWEI-IF-EXT-MIB, which can be shown as below:

Description of Single Objects

hwIFExtPhyStatus

OID

Object Name

Syntax

Max Access

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.1.1.2

hwIFExtPhyStatus

INTEGER{up(1),down(2)}

Accessible-for-notify

The value of this object identifies the physical status of the member interface.

  • 1: up
  • 2: down

This object is implemented as defined in the corresponding MIB files.

hwIFExtMemberOf

OID

Object Name

Syntax

Max Access

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.1.1.3

hwIFExtMemberOf

DisplayString

Accessible-for-notify

This object indicates the main interface that corresponds to the member interface.

This object is implemented as defined in the corresponding MIB files.

hwIFExtPhyNumber

OID

Object Name

Syntax

Max Access

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.1.1.5

hwIFExtPhyNumber

Integer32

read-only

This object indicates the number of physical interfaces.

This object is implemented as defined in the corresponding MIB file.

hwTrunkIfMax

OID

Object Name

Syntax

Max Access

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.1.3.1

hwTrunkIfMax

Integer

Read-only

The value of this object identifies the maximum number of supported trunk interfaces.

A maximum of 128 trunk interfaces can be created.

If the device is equipped with boards specified in the assign trunk command, you can run the assign trunk command to set the value, and run the display trunk configuration command to view the configuration.

hwTrunkNextIndex

OID

Object Name

Syntax

Max Access

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.1.3.2

hwTrunkNextIndex

Integer

Read-only

The value of this object identifies the index of the trunk interface that is to be created. You are recommended to use this value as the index when creating the trunk interface. You can also use other values within the range. After all the trunk interfaces are created, the value is -1.

This object is implemented as defined in the corresponding MIB files.

hwTrunkSystemPriority

OID

Object Name

Syntax

Max Access

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.1.3.4

hwTrunkSystemPriority

Integer(0..65535)

Read-write

The value of this object identifies the system priority defined in the Link Aggregation Control Protocol (LACP).

This object is implemented as defined in the corresponding MIB files.

hwTrunkETrunkSystemPriority

OID

Object Name

Syntax

Max Access

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.1.3.6

hwTrunkETrunkSystemPriority

Integer (0..65535)

Read-write

The value of this object identifies the LACP priority of an E-Trunk. The value ranges from 0 to 65535.

By default, the value is 32768.

This object is implemented as defined in the corresponding MIB files.

hwTrunkETrunkSystemID

OID

Object Name

Syntax

Max Access

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.1.3.7

hwTrunkETrunkSystemID

PhysAddress

Read-write

This object indicates the LACP system ID of an E-Trunk. The value ranges from 0-0-1 to FFFF-FFFF-FFFE.

This object is implemented as defined in the corresponding MIB files.

hwTrunkCount

OID

Object Name

Syntax

Max Access

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.1.3.8

hwTrunkCount

Integer32 (0..65535)

read-only

The value of this object identifies the number of trunk interfaces that have been configured on the device.

This object is implemented as defined in the corresponding MIB file.

hwIFFlowStatGlobalInterval

OID

Object Name

Syntax

Max Access

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.1.5.1

hwIFFlowStatGlobalInterval

Integer

Read-write

The value of this object identifies the interval for collecting the statistics of the interface traffic globally. The value ranges from 10 to 600, in seconds. In addition, the value must be a multiple of 10.

The default value is 300.

This object is implemented as defined in the corresponding MIB files.

hwLinkDownReason

OID

Object Name

Syntax

Max Access

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.1.20.1

hwLinkDownReason

INTEGER {

physicalLinkDown(1),

lacpNegotiationFailed(2),

receiveConfReqPacket(3),

receiveConfAckPacket(4),

receiveNakPacket(5),

receiveTermPacket(6),

receiveTermAckPacket(7),

receiveCodeRejPacket(8),

receiveProtoRejPacket(9),

chapAuthenticationFailed(10),

papAuthenticationFailed(11),

keepaliveOutOfTime(12),

pvcDown(13),

efmSessionFailed(14),

tunnelDownOrInexist(15),

admindown(16),

protocoldown(17),

adminup(18),

protocolup(19),

mainifdown(20),

}

Accessible-for-notify

This object indicates the reason for the link Down event.

This object is implemented as defined in the corresponding MIB files.

hwMainIfName

OID

Object Name

Syntax

Max Access

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.1.20.2

hwMainIfName

DisplayString

Accessible-for-notify

This object indicates the name of a phsyical main interface.

This object is implemented as defined in the corresponding MIB files.

hwCfmOverPhysicalName

OID

Object Name

Syntax

Max Access

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.1.20.3

hwCfmOverPhysicalName

DisplayString

Accessible-for-notify

This object indicates configuration restoration information after an interface board is installed.

This object is implemented as defined in the corresponding MIB files.

Description of MIB Tables

hwIFExtTable

hwIFExtIndex uniquely identifies this table. The index is set when the table is created, and cannot be modified.

This table describes the extension attributes of the interface, such as the frame type, and the flag that indicates the interface switching between the Layer 2 mode and the Layer 3 mode.

The index of this table is hwIFExtIndex.

OID

Object Name

Syntax

Max Access

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.1.1.1.1.1

hwIFExtIndex

InterfaceIndex

Not-accessible

The value of this object identifies the interface index.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.41.1.1.1.1.2

hwIFExtLayer

INTEGER

{

Layer2(1),

Layer3(2)

}

Read-write

The value of this object identifies the flag that indicates the interface switching between the Layer 2 mode and the Layer 3 mode. According to the specific switch command, you can see the following:

  • When Layer2(1) is 1, the interface switches from Layer 3 to Layer 2.
  • When Layer3(2) is 2, the port switches from Layer 2 to Layer 3.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.41.1.1.1.1.3

hwIFExtFrameType

INTEGER

{

ethernet-II(1),

ethernet-Snap(2),

ethernet-8022(3),

ethernet-8023(4),

Other(5)

}

Read-only

The value of this object identifies the frame type that is accepted by the VLAN virtual interface.

Currently, only the first type ethernet-II(1) is supported.

1.3.6.1.4.1.2011.5.25.41.1.1.1.1.4

hwIFExtFlowStatInterval

Integer32 (10..600)

Read-write

The value of this object identifies the interval for collecting statistics of the interface traffic. The value ranges from 10 to 600, in seconds. In addition, the value must be a multiple of 10.

By default, the value is 300.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.41.1.1.1.1.8

hwIFExtFlowStatus

INTEGER{flowUp(1),flowDown(2)}

Read-only

The value of this object identifies the status of the interface traffic.

  • 1: indicates that the traffic is Up.

  • 2: indicates that the traffic is Down.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.41.1.1.1.1.9

hwIFExtMtu

Integer32

Read-write

This object indicates the Max Transmit Unit (MTU) of the interface.

The default value is 1500 bytes.

The MTU value range and the default MTU value of an interface vary with the interface type.

1.3.6.1.4.1.2011.5.25.41.1.1.1.1.10

hwIFExtMacAddr

PhysAddress

Read-write

The value of this object identifies the MAC address of the interface.

Currently, the maximum access is read-only.

1.3.6.1.4.1.2011.5.25.41.1.1.1.1.13

hwIFExtSuppressStatus

INTEGER

{

unsuppress(0),

suppress(1)

}

read-only

This object indicates whether control-flap is configured for the interface that frequently alternates between Up and Down. The value can be:
  • 0, unsuppress: control-flap is not configured.
  • 1, suppress: control-flap is configured.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.41.1.1.1.1.15

hwIFExtInputPktRate

Gauge32

Read-only

This object indicates the rate of the incoming packets on an interface. The rate value is 64 bits. hwIFExtInputPktRate indicates the lower 32 bits, while hwIFExtInputHighPktRate indicates the higher 32 bits.

Currently, this object supports only Ethernet interfaces and does not support their sub-interfaces.

1.3.6.1.4.1.2011.5.25.41.1.1.1.1.16

hwIFExtInputHighPktRate

Gauge32

Read-only

This object indicates the rate of the incoming packets on an interface. The rate value is 64 bits. hwIFExtInputPktRate indicates the lower 32 bits, while hwIFExtInputHighPktRate indicates the higher 32 bits.

Currently, this object supports only Ethernet interfaces and does not support their sub-interfaces.

1.3.6.1.4.1.2011.5.25.41.1.1.1.1.17

hwIFExtOutputPktRate

Gauge32

Read-only

This object indicates the rate of the outgoing packets on an interface. The rate value is 64 bits. hwIFExtOutputPktRate indicates the lower 32 bits, while hwIFExtOutputHighPktRate indicates the higher 32 bits.

Currently, this object supports only Ethernet interfaces and does not support their sub-interfaces.

1.3.6.1.4.1.2011.5.25.41.1.1.1.1.18

hwIFExtOutputHighPktRate

Gauge32

Read-only

This object indicates the rate of the outgoing packets on an interface. The rate value is 64 bits. hwIFExtOutputPktRate indicates the lower 32 bits, while hwIFExtOutputHighPktRate indicates the higher 32 bits.

Currently, this object supports only Ethernet interfaces and does not support their sub-interfaces.

1.3.6.1.4.1.2011.5.25.41.1.1.1.1.19

hwIFExtInputOctetRate

Gauge32

Read-only

This object indicates the octet rate of the incoming traffic on an interface. The rate value is 64 bits. hwIFExtInputOctetRate indicates the lower 32 bits, while hwIFExtInputHighOctetRate indicates the higher 32 bits.

Currently, this object supports only Ethernet interfaces and does not support their sub-interfaces.

1.3.6.1.4.1.2011.5.25.41.1.1.1.1.20

hwIFExtInputHighOctetRate

Gauge32

Read-only

This object indicates the octet rate of the incoming traffic on an interface. The rate value is 64 bits. hwIFExtInputOctetRate indicates the lower 32 bits, while hwIFExtInputHighOctetRate indicates the higher 32 bits.

Currently, this object supports only Ethernet interfaces and does not support their sub-interfaces.

1.3.6.1.4.1.2011.5.25.41.1.1.1.1.21

hwIFExtOutputOctetRate

Gauge32

Read-only

This object indicates the octet rate of the outgoing traffic on an interface. The rate value is 64 bits. hwIFExtOutputOctetRate indicates the lower 32 bits, while hwIFExtOutputHighOctetRate indicates the higher 32 bits.

Currently, this object supports only Ethernet interfaces and does not support their sub-interfaces.

1.3.6.1.4.1.2011.5.25.41.1.1.1.1.22

hwIFExtOutputHighOctetRate

Gauge32

Read-only

This object indicates the octet rate of the outgoing traffic on an interface. The rate value is 64 bits. hwIFExtOutputOctetRate indicates the lower 32 bits, while hwIFExtOutputHighOctetRate indicates the higher 32 bits.

Currently, this object supports only Ethernet interfaces and does not support their sub-interfaces.

1.3.6.1.4.1.2011.5.25.41.1.1.1.1.23

hwIFExtSwitchPortIndex

Integer32

Read-only

This object indicates the L2 port index.

NOTE:
The interface is not a Layer 2 interface when the value is -1.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.41.1.1.1.1.24

hwIFExtSuppressStatusIPv6

INTEGER

{

unsuppress(0),

suppress(1)

}

read-only

This object indicates whether IPv6 control-flap is configured for the interface that frequently alternates between Up and Down. The value can be:
  • 0, unsuppress: control-flap is not configured.
  • 1, suppress: control-flap is configured.

This object is implemented as defined in the corresponding MIB file.

Creation Restriction

No entry can be created in this table.

Modification Restriction

Except for HwIFExtLayer, hwIFExtFlowStatInterval, hwIFExtMtu, and hwIFExtMacAddr, other entries in this table cannot be modified.

Deletion Restriction

The entries in this table cannot be deleted.

Access Restriction

hwIFExtMacAddr returns 0-0-0 for the interfaces that do not support MAC address.

hwIfIpTable

hwIfIpTable describes the IP address of an interface. You can create one primary IP address and multiple secondary IP addresses on the interface. You can create, delete, and view the IP address configuration in this table.

The index of this table is hwIpAdEntAddr.

OID

Object Name

Syntax

Max Access

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.1.2.1.1.1

hwIpAdEntAddr

IpAddress

Read-only

This object indicates the IP address of the interface.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.2.1.1.2

hwIpAdEntIfIndex

Integer

Read-create

The value of this object identifies the index of the interface that is configured with an IP address.

The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.2.1.1.3

hwIpAdEntNetMask

IpAddress

Read-create

This object indicates the subnet mask of the IP address.

The value of the mask is in the type of an IP address with all the network bits set to 1 and all the host bits set to 0.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.2.1.1.4

hwIpAdEntBcastAddr

Integer

Read-only

This object indicates whether interfaces receive the packet with the broadcast IP address. At present, all interfaces configured with IP addresses return the value 1.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.2.1.1.5

hwIpAdEntReasmMaxSize

Integer (0..65535)

Read-only

The value of this object identifies the maximum number of packets received by this IP interface.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.2.1.1.6

hwIpAdEntAddressType

HwIpAddressType

Read-create

The value of this object identifies whether the IP address is a primary IP address.

One interface has only one primary IP address, but can have many sub IP addresses. So when you add a primary IP address to an interface that has already a primary IP address, the new primary address will replace old primary address, and the old primary address is deleted.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.2.1.1.7

hwIfIpMethod

INTEGER

{

assignedIp(1), dhcpIp(2), bootpIp(3), other(4), linklayer(5), random(6)

}

Read-write

The value of this object identifies the mode of obtaining an IP address.

  • assignedIp(1) indicates that the address was manually configured to a specified address, for example, by user configuration.
  • dhcpIp(2) indicates an address that was assigned to this system by a DHCP server.
  • bootpIp(3) indicates an address that was assigned to this system by the bootp protocol.
  • other(4) indicates an address created by another method.
  • linklayer(5) indicates an address created by IPv6 stateless auto-configuration.
  • random(6) indicates an address chosen by the system at random, for example, an IPv4 address within 10.1.0.0/16, or an RFC 3041 privacy address.

Currently, the maximum access is read-only.

1.3.6.1.4.1.2011.5.25.41.1.2.1.1.8

hwIpAdEntAddrStatus

RowStatus

Read-create

The value of this object identifies the status of the row.

Currently, the values are as follows:

  • active(1)

  • notInService(2)

  • notReady(3)

  • createAndGo(4)

  • createAndWait(5)

  • destroy(6)

This object is implemented as defined in the corresponding MIB files.

Creation Restriction

The entries in this table can be created. You can create the primary IP address, and then the secondary IP address on the interface. The newly-created IP address and mask cannot be the same as the existing ones.

Modification Restriction

After the IP address is created, the attribute of the IP address cannot be modified, because all the attributes of the IP address, except the row status, are closely associated with the IP address.

Currently, entries in hwIpAdEntIfIndex, hwIpAdEntNetMask, hwIpAdEntAddressType, and hwIfIpMethod can be created, but cannot be modified.

Deletion Restriction

The entries in this table can be deleted.

Access Restriction

The entries in this table can be read without restriction.

hwIfIpUnnumberedTable

This table contains information about IP address unnumbered.

The index of this table is hwUnnumberedIfIndex.

OID

Object Name

Syntax

Max Access

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.1.2.2.1.1

hwUnnumberedIfIndex

InterfaceIndex

Not-accessible

The value of this object identifies the index of the unnumbered interface.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.2.2.1.11

hwLendIfIndex

InterfaceIndex

Read-create

The value of this object identifies the index of the interface that lends the IP address.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.2.2.1.12

hwLendIpAddr

IpAddress

Read-only

This object indicates the IP address lent by an interface.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.2.2.1.13

hwLendIpAddrNetMask

IpAddress

Read-only

This object indicates the IP address mask of the interface that lends the IP address.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.2.2.1.51

hwUnnumberedRowStatus

RowStatus

Read-create

This object indicates the row status.

Currently, the return value active(1) is supported only.

Creation Restriction

You can create entries in this table.

The interface that lends the IP address cannot be configured as the unnumbered interface.

An unnumbered interface acquires the IP address 0.0.0.0 after borrowing the IP address from an interface with no IP address.

The unnumbered interface cannot lend the IP address to another interface.

Modification Restriction

The entries in this table have no modification restriction. The index of the interface that lends the IP address can be modified.

Deletion Restriction

The entries in this table can be deleted.

Access Restriction

The entries in this table can be read without restriction.

hwIfIpAddrTable

hwIfIpAddrTable describes the IP address information of an interface.

The index of this table is hwIfIpAddrEntIfIndex and hwIfIpAddrEntAddr.

OID

Object Name

Syntax

Max Access

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.1.2.3.1.1

hwIfIpAddrEntIfIndex

InterfaceIndex

accessible-for-notify

This object indicates the index of an interface. The interface with this index is the same as the interface specified by the ifIndex in the IF-MIB.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.2.3.1.2

hwIfIpAddrEntAddr

IpAddress

accessible-for-notify

This object indicates the IP address of an interface.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.2.3.1.3

hwIfIpAddrEntType

INTEGER {

unicast(1),

anycast(2),

broadcast(3)

}

Read-only

This object indicates the address type.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.2.3.1.4

hwIfIpAddrEntPrefix

IpAddress

Read-only

This object indicates the subnet mask of an IP address.

The subnet mask is all the IP addresses with the network bit as 1 and the host bit as 0.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.2.3.1.5

hwIfIpAddrEntOrigin

INTEGER {

assignedIp(1),

dhcpIp(2),

bootpIp(3),

other(4),

linklayer(5),

random(6)

}

Read-only

This object indicates how the IP address of an interface is obtained.
  • assignedIp (1) indicates that the IP address is manually configured.
  • dhcpIp(2) indicates that the IP address is assigned by the DHCP server.
  • bootpIp(3) indicates that the IP address is obtained using BOOTP.
  • other(4) indicates that the IP address is obtained using other methods.
  • linklayer(5) indicates that the IPv6 address is obtained by stateful address autoconfiguration.
  • random(6) indicates that the IP address is randomly selected by the system. For example, the system selects an IPv4 address on the network segment 10.1.0.0/16 or selects a private address defined in RFC 3041.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.2.3.1.6

hwIfIpAddrEntStatus

INTEGER {

preferred(1),

deprecated(2),

invalid(3),

inaccessible(4),

unknown(5),

tentative(6),

duplicate(7),

optimistic(8)

}

Read-only

This object indicates whether the IP address can be used for communication. The value is preferred (1) for IPv4 addresses.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.2.3.1.7

hwIfIpAddrEntCreated

TimeStamp

Read-only

This object indicates the time when a node is created.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.2.3.1.8

hwIfIpAddrEntLastChanged

TimeStamp

Read-only

This object indicates the time when a node is modified.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.2.3.1.9

hwIfIpAddrEntBcastAddr

Integer32

Read-only

This object indicates a broadcast IP address.

Packets with a broadcast IP address are transmitted on all local interfaces.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.2.3.1.10

hwIfIpAddrEntReasmMaxSize

Integer32 (SIZE (0..65535))

Read-only

This object indicates the longest packet received by the interface.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.2.3.1.11

hwIfIpAddrEntAddrType

INTEGER{primary(1), sub(2)}

Read-only

This object indicates whether the IP address is a primary or secondary one.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.2.3.1.12

hwIfIpAddrEntVpn

DisplayString (SIZE (0..31))

Read-only

This object indicates the VPN name of the IP address. A public network address does not have this value.

This object is implemented as defined in the corresponding MIB files.

Creation Restriction

The entries in this table cannot be created.

Modification Restriction

The entries in this table cannot be modified.

Deletion Restriction

The entries in this table cannot be deleted.

Access Restriction

The entries in this table can be read without restriction.

hwIfQueryTable

This table describes the information about the interface index acquired based on the interface name.Currently, the entries in this table can only be queried.

The index of this table is hwIfName.

OID

Object Name

Syntax

Max Access

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.1.12.1.1.1

hwIfName

OCTET STRING (SIZE (1..47))

accessible-for-notify

This object indicates the interface name.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.12.1.1.2

hwIfIndex

InterfaceIndex

Read-only

This object indicates the interface index.

This object is implemented as defined in the corresponding MIB files.

Creation Restriction

No entry can be created in this table.

Modification Restriction

The entries in this table cannot be modified.

Deletion Restriction

The entries in this table cannot be deleted.

Access Restriction

This table can only support the get operation, and cannot support the getNext operation.

hwLogicIfTable

In this table, you can create, delete, and display the logical interface and sub-interface.

The index of this table is hwLogicIfIndex.

OID

Object Name

Syntax

Max Access

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.1.13.1.1.1

hwLogicIfIndex

InterfaceIndexOrZero

Not-accessible

This object indicates the interface index. The interface index must be 0 in the process of creating this interface. Then the system automatically distributes the interface index.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.13.1.1.11

hwLogicIfMainIndex

InterfaceIndexOrZero

Read-only

This object indicates the interface index of a main interface that contains a sub-interface. The value is 0 for other interfaces.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.13.1.1.12

hwLogicIfType

INTEGER

Read-create

The value of this object identifies the interface type.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.13.1.1.13

hwLogicIfName

DisplayString (SIZE(1..64))

Read-create

This object indicates the interface name. It is a string expressing the full name of the interface, without space or tab.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.13.1.1.14

hwLogicIfParaOne

INTEGER

{

p2p(1),

p2mp(2),

none(255)

}

Read-create

The value of this object identifies the extended parameters of a logical interface. The default value is p2mp(2).

The object returns "none" for other interfaces after the get operation.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.13.1.1.51

hwLogicIfRowStatus

RowStatus

Read-create

This object indicates the row status.

This object is implemented as defined in the corresponding MIB files.

Creation Restriction

The interface index must be 0 in the process of creating this object. Then the system automatically distributes the interface index. This object is created based on the interface index.

Modification Restriction

The entries in this table cannot be modified.

Deletion Restriction

The entries in this table can be deleted based on the interface index.

Access Restriction

In this table, you can read the information about the interfaces.

hwTrunkIfTable

hwTrunkIfID uniquely identifies this table. hwTrunkIfID is set when the table is created. This table describes the information about the trunk interface.

The index of this table is hwTrunkIndex.

OID

Object Name

Syntax

Max Access

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.1.3.3.1.1

hwTrunkIndex

Integer

Not-accessible

The value of this object identifies the index of the trunk interface.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.3.3.1.2

hwTrunkIfID

Integer

Read-create

The value of this object identifies the number of the trunk interface.

It may identify Trunk and is an index of the interface.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.3.3.1.3

hwTrunkIfType

INTEGER

{

eth-trunk(1),

}

Read-create

The value of this object identifies the type of the trunk interface.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.3.3.1.4

hwTrunkIfIndex

InterfaceIndex

Read-only

The value of this object identifies the index of the trunk interface.

It is consistent with ifIndex of ifTable in IF-MIB.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.3.3.1.5

hwTrunkIfModel

INTEGER

{

packetAll(1),

sourceDesMac(2),

packetUdp(3),

packetTcp(4),

sourceDesIp(5),

sourceMacIpv6(6),

sourceIpIpv6(7),

sourceIp(8),

desIp(9),

sourceMac(10),

desMac(11),

sourcePort(12),

desPort(13),

sourceDesPort(14),

fwdType(15),

qos(16),

labelNum(17),

label(18),

enhanced(19),

l4(20),

invalid(-1)

}

Read-create

The value of this object identifies the load balancing mode.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.3.3.1.6

hwTrunkIfBandWidthAffectLinkNum

Integer

Read-create

The value of this object identifies the upper threshold of the trunk interface.

By default, the upper threshold for the number of active interfaces in an Eth-Trunk is 8.

If the device is equipped with boards specified in the assign trunk command, you can run the assign trunk command to set the value, and run the display trunk configuration command to view the configuration.

You can only set this value on Layer 2 interface.

This object is not supported by Layer 3 Eth-Trunk interfaces or Eth-Trunk interfaces in active/standby mode, and the return value of this object is -1.

Currently, the maximum access is read-write.

1.3.6.1.4.1.2011.5.25.41.1.3.3.1.7

hwTrunkIfMinLinkNum

INTEGER

Read-create

The value of this object identifies the lower threshold of the trunk interface.

The currently supported value ranges from 1 to 8. By default, the lower threshold of the created trunk interface is 1.

If the device is equipped with boards specified in the assign trunk command, you can run the assign trunk command to set the value, and run the display trunk configuration command to view the configuration.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.3.3.1.8

hwTrunkIfRowStatus

RowStatus

{

active(1),

notInService(2),

notReady(3),

createAndGo(4),

createAndWait(5),

destroy(6)

}

Read-create

The value of this object identifies the status of the row.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.3.3.1.9

hwTrunkIfWorkingMode

INTEGER

{

masterBackup(1),

normalMode(2),

lacpMode(3),

lacpCompatibleMode(4),

portStandbyMode(5),

invalid(-1)

}

Read-create

The value of this object identifies the current working mode of trunk.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.3.3.1.10

hwTrunkIfWorkingState

INTEGER

{

generalMode(1),

initialization(2),

masterWorking(3),

backupWorking(4),

invalid(-1)

}

Read-only

The value of this object identifies the current working state of Trunk interface.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.3.3.1.12

hwTrunkIfPreemptEnable

INTEGER

{

enabled(1),

disabled(2),

invalid(-1)

}

Read-create

This object indicates whether LACP priority preemption is enabled in static mode.

By default, the function is disabled.

This object is a specific attribute of Eth-Trunk interfaces in static LACP mode, and the fixed return value is -1.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.3.3.1.13

hwTrunkIfPreemptDelay

Integer (0..180 | -1)

NOTE:
The specific minimum specification depends on products. The value ranges from 10 to 180 on the switch.

Read-create

The value of this object identifies the hold period for LACP priority preemption. This object takes effect only when the object hwTrunkIfPreemptEnable is enabled. The value ranges from 10 to 180, in second. By default, the value is 30.

This object is a specific attribute of Eth-Trunk interfaces in static LACP mode, and the fixed return value is -1.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.3.3.1.14

hwTrunkIfTimeoutReceive

INTEGER

{

fast(1),

slow(2),

invalid(-1)

}

Read-create

The value of this object identifies the timeout period for receiving LACP packets on an interface in static LACP mode:

  • fast: indicates that the timeout period for receiving packets is 3s.

  • slow: indicates that the timeout period for receiving packets is 90s.

  • invalid(-1): This object is a specific attribute of Eth-Trunk interfaces in static LACP mode, and the fixed return value is -1.

By default, the value is 90s.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.3.3.1.19

hwTrunkIfStatReset

INTEGER

{

reset(1),

ready(2),

invalid(-1)

}

Read-create

This value of this object identifies the function to reset the statistic information of LacpRevPdu, LacpSentPdu, MarkerRevPdu, and MarkerSentPdu for all the ports in the current trunk.

This object is a specific attribute of Eth-Trunk interfaces in static LACP mode, and the fixed return value is -1.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.3.3.1.20

hwTrunkBandwidth

Integer(0..10000 | -1)

Read-create

This value of this object identifies current bandwidth of trunk.

The value of this object is a specific attribute of Layer 3 Eth-Trunk interfaces, and the fixed return value is -1.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.3.3.1.22

hwTrunkIfLagSelectedPortStd

INTEGER

{

speed(1),

priority(2),

invalid(-1)

}

Read-create

This object indicates the basis of selecting active interfaces in the Eth-Trunk working in static LACP mode. The value can be:
  • Interface rate

  • Interface priority

  • invalid(-1): This object is a specific attribute of Eth-Trunk interfaces in static LACP mode, and the fixed return value is -1.
By default, the interface priority is adopted.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.3.3.1.23

hwTrunkIfLagMaxActiveLinkNum

Integer(1..32 | -1)

Read-create

The value of this object identifies the upper threshold of the selected interface in the Eth-Trunk working in static LACP mode.

This object is a specific attribute of Eth-Trunk interfaces in static LACP mode, and the fixed return value is -1.

The value ranges from 1 to 8.The default value is 8.

If the device is equipped with boards specified in the assign trunk command, you can run the assign trunk command to set the value, and run the display trunk configuration command to view the configuration.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.3.3.1.24

hwTrunkETrunkPriority

Integer (0..65535 | -1)

Read-write

The LACP priority of the E-Trunk.

If the LACP priority is configured, the E-Trunk sends LACP packets through member Eth-Trunk interfaces according to the configured LACP priority. If the LACP priority is not configured, the LACP priority of the E-Trunk is 32768 by default.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.3.3.1.25

hwTrunkETrunkSysID

PhysAddress

read-write

The LACP system ID of the E-Trunk.

If the LACP system ID is configured, the E-Trunk sends LACP packets through member Eth-Trunk interfaces according to the configured LACP system ID. If the LACP system ID is not configured, the LACP system ID of the E-Trunk is default.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.3.3.1.26

hwTrunkETrunkPriorityReset

INTEGER

{

yes(1),

no(2),

invalid(-1)

}

read-write

The object deletes the hwTrunkETrunkPriority configuration, and identifies whether the default value ( 32768 ) is used for the current hwTrunkETrunkPriority

By default, the status of this object is no.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.3.3.1.27

hwTrunkETrunkSysIDReset

INTEGER

{

yes(1),

no(2),

invalid(-1)

}

read-write

The object deletes the hwTrunkETrunkSysID configuration, and identifies whether he original system ID is used for the current hwTrunkETrunkSysID

By default, the status of this object is no.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.3.3.1.28

hwTrunkLocalPrefMode

INTEGER

{

enable(1),

disable(2)

}

Read-write

This object indicates whether the inter-board Eth-Trunk is enabled to preferentially forward local traffic.
  • enable: indicates that the inter-board Eth-Trunk is enabled to preferentially forward local traffic.

  • disable: indicates that the inter-board Eth-Trunk is disabled from preferentially forwarding local traffic.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.3.3.1.35

hwTrunkIfLagTimeOut

Integer32 (3..90 | 0)

read-write

The value of this object modifies the timeout period for an Eth-Trunk interface in fast mode to receive LACP packets.

By default, the timeout period for an Eth-Trunk interface in fast mode to receive LACP packets is 3s.

If the fast mode is not adopted, the value of this object is 0.

This object is implemented as defined in the corresponding MIB file.

1.3.6.1.4.1.2011.5.25.41.1.3.3.1.36

hwTrunkMemCount

Integer32

read-only

The value of this object identifies the number of member interfaces of a trunk interface.

This object is implemented as defined in the corresponding MIB file.

Creation Restriction

You can create entries in this table.

Modification Restriction

hwTrunkIfType in this table cannot be modified. Currently, hwTrunkIfMinLinkNum supports only the Eth-Trunk, and does not support the IP-Trunk.

enhanced(19) for hwTrunkIfModel in this table cannot be modified.

Deletion Restriction

The entries in this table can be deleted.

Access Restriction

The entries in this table can be read without restriction.

hwTrunkMapTable

hwTrunkMapTable describes the mapping between Eth-Trunk interface IDs and interface indexes.

The indexes of this table are hwTrunkMapType and hwTrunkMapID.

OID

Object Name

Syntax

Max Access

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.1.21.1.1.1

hwTrunkMapType

INTEGER

{

ethTrunk(1),

ipTrunk(2)

}

accessible-for-notify

The value of this object identifies the type of the trunk interface.
  • Eth-Trunk
  • IP-Trunk
NOTE:
IP-Trunk is not supported on the switch.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.21.1.1.2

hwTrunkMapID

Integer32

accessible-for-notify

The value of this object identifies the ID of the trunk interface.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.21.1.1.3

hwTrunkMapIndex

Integer32

read-only

The value of this object identifies the index of the trunk interface.

This object is implemented as defined in the corresponding MIB files.

Creation Restriction

The entries in this table cannot be created.

Modification Restriction

The entries in this table cannot be modified.

Deletion Restriction

The entries in this table cannot be deleted.

Access Restriction

The entries in this table can be read without restriction.

hwTrunkMemTable

hwTrunkMemifIndex uniquely identifies this table. It is set when the table is created. This table describes the information about the trunk member.

The indexes of this table are hwTrunkIndex and hwTrunkMemifIndex.

OID

Object Name

Syntax

Max Access

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.1.4.1.1.1

hwTrunkMemifIndex

Integer

accessible-for-notify

The value of this object identifies the index of the trunk member interface.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.4.1.1.2

hwTrunkValidEntry

INTEGER

{

valid(1),

invalid(2)

}

Read-only

The value of this object identifies whether member interfaces are added to the trunk interface.

If at least one member interface is added to the trunk interface, the value is valid(1).

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.4.1.1.3

hwTrunkSelectStatus

INTEGER

{

trunkSelected(1),

trunkDeselected(2)

trunkIndep(3)

invalid(-1)

}

Read-create

The value of this object identifies whether a trunk interface is in the forwarding state.

By default, the value is trunk_Deselected(2).

This object is a specific attribute of Eth-Trunk interfaces in static LACP mode, and the return value for other types of Eth-Trunk interfaces is alway -1.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.4.1.1.4

hwTrunkLacpStatus

EnabledStatus

Read-only

The value of this object identifies LACP status:
  • enabled: The Eth-Trunk works in static LACP mode.
  • disabled: The Eth-Trunk works in non-static LACP mode.

This object is invalid and the fixed value is 2.

1.3.6.1.4.1.2011.5.25.41.1.4.1.1.6

hwTrunkOperstatus

INTEGER

{

up(1),

down(2)

}

Read-only

The value of this object identifies the status of the Trunk member interface.

By default, its value is down(2).

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.4.1.1.8

hwTrunkPortWeight

Unsigned32

Read-create

This object indicates the member interface weight.

Currently, the value ranges from 1 to 16. By default, the value is 1.

Currently, the maximum access is read-only.

1.3.6.1.4.1.2011.5.25.41.1.4.1.1.10

hwTrunkRowStatus

RowStatus

{

active(1),

notInService(2),

notReady(3),

createAndGo(4),

createAndWait(5),

destroy(6)

}

Read-create

The value of this object identifies the status of the row.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.4.1.1.12

hwTrunkPortPriority

Integer (0..65535 | -1)

Read-create

The value of this object identifies the priority value assigned to the trunk interface.

NOTE:

This object takes effect only on Eth-Trunk interfaces in static LACP mode.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.4.1.1.13

hwTrunkPortStatReset

INTEGER

{

reset(1),

ready(2),

invalid(-1)

}

Read-create

The value of this object identifies the status of a member interface of an Eth-Trunk interface in static LACP mode.

This object is a specific attribute of member interfaces of an Eth-Trunk interface in static LACP mode. The return value of the member interfaces in other roles is -1.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.4.1.1.14

hwTrunkPortLacpMode

INTEGER

{

invalid(1),

active(2),

passive(3)

}

Read-create

The value of this object identifies the mode in which an Eth-Trunk interface in static LACP mode sends packets.

This object is implemented as defined in the corresponding MIB file.

Creation Restriction

You can create entries in this table.

Modification Restriction

At present, the entry hwTrunkSelectStatus in this table cannot be modified.

Deletion Restriction

The entries in this table can be deleted.

Access Restriction

The entries in this table can be read without restriction.

hwIfMonitorThresholdTable

This table is used to query and configure alarm messages.

The index of this table is hwIfMonitorIndex.

OID

Object Name

Syntax

Maximum Access

Description

Access

1.3.6.1.4.1.2011.5.25.41.1.7.1.1.1

hwIfMonitorIndex

InterfaceIndex

Not-accessible

This object indicates the interface index.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.7.1.1.2

hwIfMonitorCrcErrorStatistics

Counter64

Read-only

This object indicates the number of packets with CRC errors.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.7.1.1.3

hwIfMonitorCrcErrorThreshold

Integer32

Read-write

This object indicates the alarm threshold of CRC error packets. The value is an integer that ranges from 1 to 65535.

The default value is 3.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.7.1.1.4

hwIfMonitorCrcErrorInterval

Integer32

Read-write

This object indicates the interval at which the CRC error packet alarms are reported. The value is expressed in seconds.

The default value is 10.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.7.1.1.8

hwIfMonitorInputRate

Integer32

Read-only

This object indicates the inbound bandwidth usage.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.7.1.1.9

hwIfMonitorInputRateThreshold

Integer32

Read-write

This object indicates the alarm threshold of the inbound bandwidth usage. The value ranges from 1 to 100.

The default value is 80.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.7.1.1.10

hwIfMonitorOutputRate

Integer32

Read-only

This object indicates the outbound bandwidth usage.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.7.1.1.11

hwIfMonitorOutputRateThreshold

Integer32

Read-write

This object indicates the alarm threshold of the outbound bandwidth usage. The value ranges from 1 to 100.

The default value is 80.

This object is implemented as defined in the corresponding MIB files.

Creation Restriction

No entry can be created in this table.

Modification Restriction

If the specified interface is the outbound interface for Layer 2 forwarding, the interface must be a switched interface (Layer 2 interface).

Deletion Restriction

No entry in this table can be deleted.

Access Restriction

The entries in this table can be read without restriction.

hwIfEtherStatTable

This table collects interface statistics.

The index of this table is hwIfEtherStatIfIndex.

OID

Object Name

Syntax

Maximum Access

Description

Access

1.3.6.1.4.1.2011.5.25.41.1.6.1.1.1

hwIfEtherStatIfIndex

InterfaceIndex

Not-accessible

This object indicates the interface index.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.6.1.1.11

hwIfEtherStatInJumboPkts

Counter64

Read-only

This object indicates the number of received jumbo frames.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.6.1.1.12

hwIfEtherStatInCRCPkts

Counter64

Read-only

Number of packets shorter than 1518 bytes and with incorrect FCS values.

For LE1D2S04SEC0, LE1D2X32SEC0, and LE1D2H02QEC0 cards, and X series cards, the value of this field contains the number of received packets with length larger than the jumbo frame size configured on the interface and incorrect FCS values.

For X series cards, the value of this field contains the number of received packets with length ranging from 1518 bytes to the jumbo frame size configured on the interface and incorrect FCS values.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.6.1.1.13

hwIfEtherStatInLongPkts

Counter64

Read-only

This object indicates the number of received jumbo frames with correct FCS values.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.6.1.1.14

hwIfEtherStatInJabberPkts

Counter64

Read-only

This object indicates the number of received jumbo frames with incorrect FCS values.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.6.1.1.15

hwIfEtherStatInFragmentPkts

Counter64

Read-only

This object indicates the number of undersized frames with incorrect FCS values.

For EE series cards, the value of this object is always 0.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.6.1.1.16

hwIfEtherStatInUnderSizePkts

Counter64

Read-only

This object indicates the number of undersized frames with correct FCS values.

For EE series cards, the value of this field includes the number of received fragmented packets shorter than 64 bytes and with incorrect CRC values.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.6.1.1.18

hwIfEtherStatInPausePkts

Counter64

Read-only

This object indicates the number of received control packets.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.6.1.1.19

hwIfEtherStatOutJumboPkts

Counter64

Read-only

This object indicates the number of sent jumbo frames.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.6.1.1.20

hwIfEtherStatOutOverflowPkts

Counter64

Read-only

This object indicates the number of packets with FIFO overflow errors.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.6.1.1.21

hwIfEtherStatOutUnderRunPkts

Counter64

Read-only

This object indicates the number of packets entering empty FIFO queues.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.6.1.1.22

hwIfEtherStatOutPausePkts

Counter64

Read-only

This object indicates the number of sent control packets.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.6.1.1.24

hwIfEtherStatInDropEventPkts

Counter64

Read-only

This object indicates the number of received packets that are discarded due to GBP full or back pressure.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.6.1.1.25

hwIfEtherStatInAlignmentPkts

Counter64

Read-only

This object indicates the number of received frames with alignment errors.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.6.1.1.26

hwIfEtherStatInSymbolPkts

Counter64

Read-only

This object indicates the number of unknown received packets.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.6.1.1.27

hwIfEtherStatInIgnoredPkts

Counter64

Read-only

This object indicates the number of received MAC control frames, the OpCode of which is not PAUSE.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.6.1.1.28

hwIfEtherStatInFramePkts

Counter64

Read-only

This object indicates the number of packets with the incorrect 802.3 length.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.6.1.1.29

hwIfEtherStatOutCollisionPkts

Counter64

Read-only

This object indicates the number of sent packets with collisions on the 10M/100M interface in half-duplex mode.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.6.1.1.30

hwIfEtherStatOutDeferredPkts

Counter64

Read-only

This object indicates the number of delayed outgoing packets without collision on the 10M/100M interface.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.6.1.1.31

hwIfEtherStatOutLateCollisionPkts

Counter64

Read-only

This object indicates the number of delayed outgoing packets with collisions on the 10M/100M interface.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.6.1.1.32

hwIfEtherStatOutExcessiveCollisionPkts

Counter64

Read-only

This object indicates the number of packets with 16 collisions that fail to be sent on the 10M/100M interface.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.4.1.2011.5.25.41.1.6.1.1.33

hwIfEtherStatOutBufferPurgationPkts

Counter64

Read-only

This object indicates the number of aged packets that are stored in the buffer for a long period of time.

The value of this object is always 0.

This object is implemented as defined in the corresponding MIB files.

Creation Restriction

No entry can be created in this table.

Modification Restriction

No entry in this table can be modified.

Deletion Restriction

No entry in this table can be deleted.

Access Restriction

The entries in this table can be read without restriction.

Description of Alarm Objects

hwIfFlowDown

OID

Object

Bound Variable

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.3.5

hwIfFlowDown

  • 1: sysUpTime
  • 2: hwIFExtFlowStatus

The alarm is generated when the status of the interface traffic changes to Down.

This object is implemented as defined in the corresponding MIB files.

hwIfFlowUp

OID

Object

Bound Variable

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.3.6

hwIfFlowUp

  • 1: sysUpTime
  • 2: hwIFExtFlowStatus

The alarm is generated when the status of the interface traffic reverts to Up.

This object is implemented as defined in the corresponding MIB files.

hwLacpTotalLinkLoss

OID

Object Name

Bound Variable

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.3.3

hwLacpTotalLinkLoss

1:hwTrunkIfID2:ifName

The alarm is generated when the bandwidth of a link is totally lost.

This object is implemented as defined in the corresponding MIB files.

hwLacpTotalLinkLossResume

OID

Object

Bound Variable

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.3.14

hwLacpTotalLinkLossResume

  • 1:hwTrunkIfID

  • 2:ifName

It is a trap indicating the restoration of the total link bandwidth and is a matching trap of hwLacpTotalLinkLoss.

This object is implemented as defined in the corresponding MIB files.

hwLacpPartialLinkLoss

OID

Object Name

Bound Variable

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.3.4

hwLacpPartialLinkLoss

  • 1:hwTrunkIfID
  • 2:ifName

The alarm is generated when the bandwidth of a link is partially lost.

This object is implemented as defined in the corresponding MIB files.

hwLacpPartialLinkLossResume

OID

Object

Bound Variable

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.3.15

hwLacpPartialLinkLossResume

  • 1:hwTrunkIfID

  • 2:ifName

It is a trap indicating the restoration of the partial link bandwidth and is a matching trap of hwLacpPartialLinkLoss.

This object is implemented as defined in the corresponding MIB files.

hwLacpPartnerExpiredLoss

OID

Object Name

Bound Variable

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.3.34

hwLacpPartnerExpiredLoss

  • hwTrunkIfID
  • ifName
  • ifName

This object indicates that the local end receives a timeout packet from the remote end.

This object is implemented as defined in the corresponding MIB file.

hwExtLinkDown

OID

Object Name

Bound Variable

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.3.9

hwExtLinkDown

  • 1: ifIndex
  • 2: ifAdminStatus
  • 3: ifOperStatus
  • 4: ifDescr
  • 5: hwIFExtPhyStatus
  • 6: hwIFExtMemberOf

The alarm is generated when the link protocol status of the trunk member interfaces turns Down.

This object is implemented as defined in the corresponding MIB files.

hwExtLinkUp

OID

Object Name

Bound Variable

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.3.10

hwExtLinkUp

  • 1: ifIndex
  • 2: ifAdminStatus
  • 3: ifOperStatus
  • 4: ifDescr
  • 5: hwIFExtPhyStatus
  • 6: hwIFExtMemberOf

The alarm is generated when the link protocol status of the trunk member interfaces turns Up.

This object is implemented as defined in the corresponding MIB files.

hwLacpNegotiateFailed

OID

Object Name

Bound Variable

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.3.2

hwLacpNegotiateFailed

  • 1:hwTrunkIfID
  • 2:ifName
  • 3:ifName

The alarm is generated when a member link does not send and receive packets.

This object is implemented as defined in the corresponding MIB files.

hwLacpNegotiateResume

OID

Object

Bound Variable

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.3.13

hwLacpNegotiateResume

  • 1:hwTrunkIfID

  • 2:ifName

  • 3:ifName

It is the trap indicating the successful member link negotiation and is a matching trap of hwLacpNegotiateFailed.

This object is implemented as defined in the corresponding MIB files.

hwExtAllMemberDownNotify

OID

Object Name

Bound Variable

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.3.28

hwExtAllMemberDownNotify

ifName

Indicates that last member interface of the Trunk interface becomes down.

This object is implemented as defined in the corresponding MIB files.

hwExtAllMemberDownResume

OID

Object Name

Bound Variable

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.3.29

hwExtAllMemberDownResume

ifName

Indicates that one member interface of the Trunk interface becomes up.

This object is implemented as defined in the corresponding MIB files.

hwEntityExtCfmOverSlot

OID

Object Name

Bound Variable

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.3.26

hwEntityExtCfmOverSlot

hwCfmOverPhysicalName

The configuration of the interface board was restored.

This object is implemented as defined in the corresponding MIB files.

hwExtInterfaceDelete

OID

Object Name

Bound Variable

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.3.33

hwExtInterfaceDelete

  • 1: ifIndex
  • 2: ifDescr

This notification indicates the time when the interface was deleted.

This object is implemented as defined in the corresponding MIB files.

hwIfIpAddressChange

OID

Object Name

Bound Variable

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.6.1

hwIfIpAddressChange

  • ipAdEntNetMask
  • ipAdEntNetMask
  • ifName

The IP address of an interface is changed.

This object is implemented as defined in the corresponding MIB file.

hwIfMonitorCrcErrorRising

OID

Object Name

Bound Variable

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.4.1

hwIfMonitorCrcErrorRising

  • 1:hwIfMonitorCrcErrorStatistics
  • 2:hwIfMonitorCrcErrorThreshold
  • 3:hwIfMonitorCrcErrorInterval
  • 4:hwIfMonitorName

The alarm is generated when the CRC error occurs.

This object is implemented as defined in the corresponding MIB files.

hwIfMonitorCrcErrorResume

OID

Object Name

Bound Variable

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.4.2

hwIfMonitorCrcErrorResume

  • 1:hwIfMonitorCrcErrorStatistics
  • 2:hwIfMonitorCrcErrorThreshold
  • 3:hwIfMonitorCrcErrorInterval

The alarm is generated when the CRC error is cleared.

This object is implemented as defined in the corresponding MIB files.

hwIfControlFlapSuppress

OID

Object Name

Bound Variable

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.3.31

hwIfControlFlapSuppress

  • 1: ifName
  • 2: hwIFExtSuppressStatus

This notification indicates the time when the interface's status changes from unsuppress to suppress.

This object is implemented as defined in the corresponding MIB files.

hwIfControlFlapResume

OID

Object Name

Bound Variable

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.3.32

hwIfControlFlapResume

  • 1: ifName
  • 2: hwIFExtSuppressStatus

This notification indicates the time when the interface's status changes from suppress to unsuppress.

This object is implemented as defined in the corresponding MIB files.

hwIfControlFlapSuppressIPv6

OID

Object Name

Bound Variable

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.3.42

hwIfControlFlapSuppressIPv6

  • 1: ifName
  • 2: hwIFExtSuppressStatus

This notification indicates the time when the IPv6 interface's status changes from unsuppress to suppress.

This object is implemented as defined in the corresponding MIB files.

hwIfControlFlapResumeIPv6

OID

Object Name

Bound Variable

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.3.43

hwIfControlFlapResumeIPv6

  • 1: ifName
  • 2: hwIFExtSuppressStatus

This notification indicates the time when the IPv6 interface's status changes from suppress to unsuppress.

This object is implemented as defined in the corresponding MIB files.

hwIfMonitorInputRateRising

OID

Object Name

Bound Variable

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.4.5

hwIfMonitorInputRateRising

  • 1:hwIfMonitorName
  • 2:hwIfMonitorInputRate
  • 3:hwIfMonitorInputRateThreshold

The alarm is generated when the error occurs on the inbound traffic rate.

This object is implemented as defined in the corresponding MIB files.

hwIfMonitorInputRateResume

OID

Object Name

Bound Variable

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.4.6

hwIfMonitorInputRateResume

  • 1:hwIfMonitorName
  • 2:hwIfMonitorInputRate
  • 3:hwIfMonitorInputRateThreshold

The alarm is generated when the error in the inbound traffic rate is cleared.

This object is implemented as defined in the corresponding MIB files.

hwIfMonitorOutputRateRising

OID

Object Name

Bound Variable

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.4.7

hwIfMonitorOutputRateRising

  • 1:hwIfMonitorName
  • 2:hwIfMonitorOutputRate
  • 3:hwIfMonitorOutputRateThreshold

The alarm is generated when the error occurs on the outbound traffic rate.

This object is implemented as defined in the corresponding MIB files.

hwIfMonitorOutputRateResume

OID

Object Name

Bound Variable

Description

Implemented Specifications

1.3.6.1.4.1.2011.5.25.41.4.8

hwIfMonitorOutputRateResume

  • 1:hwIfMonitorName
  • 2:hwIfMonitorOutputRate
  • 3:hwIfMonitorOutputRateThreshold

The alarm is generated when the error in the outbound traffic rate is cleared.

This object is implemented as defined in the corresponding MIB files.

Unsupported Objects

The functions corresponding to the following objects are not supported on the device. Do not use these MIB objects to maintain the device.

Table 57-1  List of unsupported objects

Object ID

Object Name

Table

1.3.6.1.4.1.2011.5.25.41.1.6.1.1.5

hwIfEtherStatInPkts64Octets

hwIfEtherStatTable

1.3.6.1.4.1.2011.5.25.41.1.6.1.1.6

hwIfEtherStatInPkts65to127Octets

hwIfEtherStatTable

1.3.6.1.4.1.2011.5.25.41.1.6.1.1.7

hwIfEtherStatInPkts128to255Octets

hwIfEtherStatTable

1.3.6.1.4.1.2011.5.25.41.1.6.1.1.8

hwIfEtherStatInPkts256to511Octets

hwIfEtherStatTable

1.3.6.1.4.1.2011.5.25.41.1.6.1.1.9

hwIfEtherStatInPkts512to1023Octets

hwIfEtherStatTable

1.3.6.1.4.1.2011.5.25.41.1.6.1.1.10

hwIfEtherStatInPkts1024to1518Octets

hwIfEtherStatTable

1.3.6.1.4.1.2011.5.25.41.1.6.1.1.17

hwIfEtherStatInOverRunPkts

hwIfEtherStatTable

1.3.6.1.4.1.2011.5.25.41.1.6.1.1.23

hwIfEtherStatResetFlag

hwIfEtherStatTable

1.3.6.1.4.1.2011.5.25.41.4.3

hwIfMonitorSdhErrorRising

An alarm object

1.3.6.1.4.1.2011.5.25.41.4.4

hwIfMonitorSdhErrorResume

An alarm object

1.3.6.1.4.1.2011.5.25.41.4.10

hwIfMonitorPauseFrameRising

An alarm object

1.3.6.1.4.1.2011.5.25.41.4.11

hwIfMonitorPauseFrameResume

An alarm object

1.3.6.1.4.1.2011.5.25.41.4.14

hwIfMonitorSdhB1ErrorRising

An alarm object

1.3.6.1.4.1.2011.5.25.41.4.15

hwIfMonitorSdhB1ErrorResume

An alarm object

1.3.6.1.4.1.2011.5.25.41.4.16

hwIfMonitorSdhB2ErrorRising

An alarm object

1.3.6.1.4.1.2011.5.25.41.4.17

hwIfMonitorSdhB2ErrorResume

An alarm object

1.3.6.1.4.1.2011.5.25.41.4.18

hwIfMonitorSymbolErrorRising

An alarm object

1.3.6.1.4.1.2011.5.25.41.4.19

hwIfMonitorSymbolErrorResume

An alarm object

1.3.6.1.4.1.2011.5.25.41.4.40

hwIfMonitorBadBytesErrorRising

An alarm object

1.3.6.1.4.1.2011.5.25.41.4.41

hwIfMonitorBadBytesErrorResume

An alarm object

Translation
Download
Updated: 2019-10-17

Document ID: EDOC1000178290

Views: 880020

Downloads: 58

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next