No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search


To have a better experience, please upgrade your IE browser.


Configuration Guide - Basic Configuration

S7700 and S9700 V200R011C10

This document describes methods to use command line interface and to log in to the device, file operations, and system startup configurations.

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
(Optional) Configuring Attributes for the Console User Interface

(Optional) Configuring Attributes for the Console User Interface


The data transmission and screen display attributes of the console user interface are as follows:
  • Data transmission attributes: transmission rate, flow control mode, parity bit, stop bit, and data bit. These attributes determine the data transmission mode used in the console port login process.
  • Screen display attributes: timeout period of a connection, number of rows and columns displayed on a terminal screen, and buffer size for historical commands. These attributes determine terminal screen display for console port login.


  1. Run system-view

    The system view is displayed.

  2. Run user-interface console 0

    The console user interface view is displayed.

  3. Configure data transmission attributes.

    The data transmission attributes configured on the terminal software must be the same as those on the device.

    1. Run speed speed-value

      The transmission rate is set.

      The default transmission rate is 9600 bit/s.

    2. Run flow-control { hardware | none | software }

      The flow control mode is set.

      The default flow control mode is set to none, indicating that the flow control function is not performed.

    3. Run databits { 5 | 6 | 7 | 8 }

      The data bit is set.

      The default data bit is 8. Data bit configuration depends on the code type used for information interchange. If standard ASCII codes are used, set the data bit to 7. If extended ASCII codes are used, set the data bit to 8.

    4. Run parity { even | mark | none | odd | space }

      The parity bit is set.

      The default parity bit is set to none, indicating that the parity check is not performed on the console port. Setting a parity bit improves data security. If packets on the console port fail to pass the parity check, the device discards the packets.

    5. Run stopbits { 1 | 1.5 | 2 }

      The stop bit is set.

      The default stop bit is 1. The stop bit indicates the end of a packet. More stop bits indicate lower transmission efficiency.

  4. Configure screen display attributes.
    1. Run idle-timeout minutes [ seconds ]

      A timeout period is set for a user connection.

      If a connection remains idle for the specified timeout period, the system automatically ends the connection after the timeout period expires.

      The default timeout period is 10 minutes.

      If you set the timeout period of a terminal connection to 0 or too long, the terminal remains logged in to a device, which is a potential security risk. It is recommended that you run the lock command to lock the connection.

    2. Run screen-length screen-length [ temporary ]

      The number of rows displayed on a terminal screen is set.

      temporary specifies the number of rows temporarily displayed on a terminal screen. If you specify this parameter, the configured value does not take effect on the next login.

      The default number of rows displayed on a terminal screen is 24.

    3. Run screen-width screen-width

      The number of columns displayed on a terminal screen is set.

      The default number of columns displayed on a terminal screen is 80. Each character is a column.

      This command is valid only for information displayed by the display interface description command.

    4. Run history-command max-size size-value

      A buffer size is set for historical commands.

      The default buffer size is 10, that is, a maximum of 10 historical commands can be buffered.

Updated: 2020-02-04

Document ID: EDOC1000178308

Views: 100800

Downloads: 152

Average rating:
This Document Applies to these Products

Related Version

Related Documents

Previous Next